Fanimation Breckenfield FP7951 Series Owner's Manual

™

The Breckenfield

Ceiling Fan

Model No. FP7951**

OWNER’S MANUAL

READ AND SAVE THESE INSTRUCTIONS

Net Weight 14kg (30.86 lbs)

Important Safety Instructions

WARNING: To avoid fire, shock and serious personal injury, follow these instructions.

1. Read your owner’s manual and safety information before installing your new fan. Review the accompanying assembly diagrams.

2. Before servicing or cleaning unit, switch power off at service panel and lock service panel disconnecting means to prevent power
from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a warning device, such
as a tag, to the service panel.

3. Be careful of the fan and blades when cleaning, painting, or working near the fan. Always turn off the power to the ceiling fan before
servicing.

4. Do not insert anything into the fan blades while the fan is operating.

5. Do not operate reversing switch until fan blades have come to a complete stop.

Additional Safety Instructions

1. To avoid possible shock, be sure electricity is turned off at the fuse box before wiring, and do not operate fan without blades.

2. All wiring and installation procedures must satisfy National Electrical Codes (ANSI/ NFPA 70-1999) and Local Codes. The ceiling fan
must be grounded as a precaution against possible electrical shock. Electrical installation should be made or approved by a licensed
electrician.

3. The fan base must be securely mounted and capable of reliably supporting at least 50 lbs. Consult a qualified electrician if in doubt.

4. The fan must be mounted with the fan blades at least 7 feet from the floor to prevent accidental contact with the fan blades.

5. Follow the recommended instructions for the proper method of wiring your ceiling fan. If you do not have adequate electrical
knowledge or experience, have your fan installed by licensed electrician.

WARNING: Suitable for use with solid-state speed control.
WARNING: This product is designed to use only those parts supplied with this product and/or accessories designated specifically for

use with this product. Using parts and/or accessories not designated for use with this product could result in personal injury or property
damage.

WARNING:

balancing the blades, or cleaning the fan. Do not insert foreign objects in between rotating fan blades.

WARNING: Use only with light kits marked suitable for use in damp locations.
WARNING: To reduce the risk of electric shock, this fan must be installed with an isolating, general use wall control/switch.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation. If the intentional radiator can be classified as a Class B digital device or a PC
peripheral, then shall include the following or equivalent:
Note: This equipment has been tested and found to comply with the limits for Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

To reduce the risk of personal injury, do not bend the blade bracket (flange or blade holder) when installing the brackets,

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and the receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

Note: For a Class A digital device, statements of 15. 105(a) must be included when appropriate for the device in question.

LIMITED LIFETIME WARRANTY

Extends to the original purchaser of a Fanimation Fan

1. LIMITED LIFETIME MOTOR WARRANTY - If any part of your fan motor fails, due to a defect in materials or workmanship during
the lifetime of the original purchaser, Fanimation will provide the replacement part free of charge, when the defective fan is returned
to our national service center. Proof of purchase is required. Customer shall be responsible for all costs incurred in the removal or
reinstallation and shipping of the product for repairs or replacement.

2. ONE YEAR MOTOR LABOR WARRANTY - If your fan motor fails at any time within one year from the original purchase, due to
defects in materials or workmanship, labor to repair the motor will be provided free of charge at our national service center. Purchaser
will be responsible for labor charges after this one-year period. Customer shall be responsible for all costs incurred in the removal or
reinstallation and shipping of the product for repairs or replacement.

3. If any other part of your fan fails at any time within one year after original purchase, due to a defect in materials or workmanship, we
will repair, or replace, at our option, the defective part free of charge for parts and labor performed at our national service center.

4. Because of varying climate conditions, this warranty does not cover changes in the finish, including rusting, pitting, corroding,
tarnishing, or peeling.

5. This warranty is void and does not apply to damage from improper installation, neglect, accident, misuse, exposure to extremes of
heat or humidity, or as a result of any modification to the original product.

6. All costs of removal and reinstallation of the fan are the sole responsibility of the owner of the fan and not the store that sold the fan
or Fanimation.

7. Fanimation reserves the right to modify or discontinue any product at any time and may substitute any part under this warranty.

8. Under no circumstances may a fan be returned without prior authorization from Fanimation. The receipt of purchase must ac­company authorized returns and must be sent freight prepaid to Fanimation. The fan to be returned must be properly packed to avoid
damage in transit; Fanimation will not be responsible for any damage resulting from improper packaging.

9. It is understood that any repair or replacement is the exclusive remedy available from Fanimation. There is no other expressed or
implied warranty. Fanimation hereby disclaims any and all implied warranties, including, but not limited to those of merchantability and
fitness for a particular purpose to the extent permitted by law. Some states do not allow limitations on implied warranties. Fanimation
will not be liable for incidental, consequential, or special damages arising out of or in conjunction with product use or performance,
except as may otherwise be accorded by law. This warranty gives you special legal rights and you may also have other rights that vary
from state to state.

10. A certain amount of wobble is normal and should not be considered a problem or a defect.

Table of Contents

Unpacking Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Energy Effi cient Use of Ceiling Fans. . . . . . . . . . . . . . . . . . . . . . . . . . 5

Electrical and Structural Requirements . . . . . . . . . . . . . . . . . . . . . . . 5

How to Assemble Your Ceiling Fan . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

How to Hang Your Ceiling Fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

How to Wire Your Ceiling Fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

How to assemble the Blades and Light kit . . . . . . . . . . . . . . . . . . . . . 11

How to Operate Your Ceiling Fan

Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Blade Cleaning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Trouble Shooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

01 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .gnisuoH yponaC eht gnillatsnI

Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Exploded-View Illustration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

This Manual is Designed to Make it as Easy as Possible for You

to Assemble, Install, Operate, and Maintain Your Ceiling Fan

Tools Needed for Assembly Materials

• One Phillips head screwdriver

• One stepladder

• One ¼˝ blade screwdriver

• One wire stripper

• Three wire connectors

(supplied)

Wiring outlet box and box connectors must be of type
required by local code. The minimum wire would be a 3­conductor (2-wire with ground) of the following size:

Wire Size A.W.G.Installed Wire Length

▲

WARNING

Before assembling your ceiling fan, refer to section on
proper method of wiring your fan (page 4). If you feel you
do not have enough wiring knowledge or experience,
have your fan installed by a licensed electrician.

Up to 50 ft.
50 - 100 ft.

NOTE: Place the parts from the loose parts bags in a small
container to keep them from being lost. If any parts are missing,
contact your local retailer.

14
12

Unpacking Instructions

For your convenience, check-off each step. As each step is completed, place a check mark. This will ensure that all
steps have been completed and will be helpful in fi nding your place should you be interrupted.

▲

WARNING

Do not install or use fan if any part is damaged or
missing. This product is designed to use only those
parts supplied with this product and/or any accessories
designated specifically for use with this product by
Fanimation. Substitution of parts or accessories not
designated for use with this product by Fanimation could
result in personal injury or property damage. Contact
your retail store for missing or damaged parts.

1. Check to see that you have received the following

parts:

NOTE: If you are uncertain of part description, refer to
exploded view illustration. (Figure 1, page 16)

Fan Motor Assembly•
Hanger Bracket Assembly•
Downrod/Hanger Ball Assembly •

Ceiling Canopy•
Canopy Screw Cover Assembly•
Motor Coupling Cover Assembly•

Light Plate Assembly•
Housing Ring Assembly•
Socket Plate Assembly•
Blade Holder Set•

Blade Set•
Glass Assembly •
Minican Light Bulb •

Remote Hand Held•
Receiver Unit•

• Hardware bag:
– Eleven ¼˝-20 x 14 mm

(blade holder to fan motor hub)
screws with lockwashers
– Sixteen
to blade holder) washer-head
screws
– Fiber Washers

– Phillips Screwdriver 4˝

– Wire Nuts
– Balance Kit

3

/16 -24 x 7.5 mm (blade

Canopy Screw Cover
Assembly

Hanger Bracket
Assembly

Ceiling Canopy

Downrod/
Hanger Ball Assembly

Motor Coupling Cover
Assembly

Fan Motor
Assembly

Light Plate Assembly

Housing Ring Assembly

Socket Plate Assembly

Glass Assembly

4

Blade Holder Set

TR24

Hand-Held Remote

Hardware Bag

Minican
Light Bulb

Receiver
Unit

Blade Set

Energy Efficient Use of Ceiling Fans

Ceiling fan performance and energy savings rely
heavily on the proper installation and use of the ceiling
fan. Here are a few tips to ensure efficient product
performance.

Choosing the Appropriate Mounting Location

Ceiling fans should be installed, or mounted, in the middle
of the room and at least7feet above the floor and 18
inches from the walls. If ceiling height allows, install the fan
8 - 9 feet above the floor for optimal airflow. Consult your
Fanimation Retailer for optional mounting accessories.

Turn Off When Not in the Room

Ceiling fans cool people, not rooms. If the room is
unoccupied, turn off the ceiling fan to save energy.

Electrical and Structural Requirements

Your new ceiling fan will requireagrounded electrical
supply line of 120 volts AC, 60 Hz, 15 amp circuit.
The outlet box must be securely anchored and
capable of withstanding a load of at least 50 lbs.
Figure 1 depicts different structural configurations
that may be used for mounting the outlet box.

Using the Ceiling Fan Year Round
Summer Season: Use the ceiling fan in the counter-

clockwise direction. The airflow produced by the ceiling
fan creates a wind-chill effect, making you “feel” cooler.
Select a fan speed that provides a comfortable breeze,
lower speeds consume less energy.
Winter Season: Reverse themotor and operate the ceiling
fan at low speed in the clockwise direction. This produces
a gentle updraft, which forces warm air near the ceiling
down into the occupied space.Remember to adjust your
thermostat when using your ceiling fan - additional energy
and dollar savings could be realized with this simple step!

Ceiling

▲

WARNING

To reduce the risk of fire, electrical shock, or personal
injury, mount fan to outlet box marked acceptable for
fan support of 15.9 kg (35lbs) or less. Use screws

supplied with outlet box. Most outlet boxes commonly
used for support of light fixtures are not acceptable for
fan support and may need to be replaced. Consult a
qualified electrician if in doubt.

▲

WARNING

Turning off wall switch is not sufficient. To avoid
possible electrical shock, be sure electricity is turned
off at the main fuse box before wiring. All wiring must
be in accordance with National and Local codes and the
ceiling fan must be properly grounded as a precaution
against possible electrical shock.

Ceiling

Joists

2˝ x 4˝

Outlet
Box

Figure 1

▲

WARNING

To avoid fire or shock, follow all wiring instructions
carefully. Any electrical work not described in these
instructions should be done or approved by a licensed
electrician.

5

How to Assemble Your Ceiling Fan

Downrod

Clevis Pin

Hairpin Clip

Downrod Support

Screwdriver

Set Screws and
Locking Nuts (2)

Figure 4

1. Remove the hanger ball portion from the downrod

/hanger ball assembly by loosening the set screw
in the hanger ball until the ball falls freely down the
downrod. Remove the pin from the downrod, then
remove the hanger ball. Retain the pin and
hanger ball for reinstallation in Step 8 (Figure 1).

2. Remove the hairpin clip and clevis pin from the

bottom of downrod. Retain the pin and clip for
reinstallation in Step 4 (Figure 2).

3. Loosen the two set screws in the downrod support.

Route black, blue and white lead wires through the
downrod (Figure 3).

Pin

Downrod

Set Screw

Hanger Ball

Figure 1

Hairpin
Clip

Clevis Pin

Figure 2

Black, Blue and
White Leads

Downrod

4. Position downrod support and align the clevis pin

holes in both parts. Install the clevis pin and secure
with the hairpin clip.Tighten the two set screws

and locking nuts in the downrod support (Figure 4).

5. Remove one of the three screws in the support

bracket at the bottom of the motor assembly.
Slight ly loosen the remaining two screws.
Assemble the light plate assembly to the support

bracket using the two keyslots in the socket plate.
Replace the third screw and securely tighten all three

screws (Figure 5).

Figure 3

Fan Motor

Assembly
Support
Bracket

Screw (3)

Light Plate
Assembly

Figure 5

6

How to Assemble Your Ceiling Fan (continued)

Assemble the housing ring assembly through

6.

the motor assembly. Slightly loosen the three
screws. Assemble the housing ring assembly
to the light plate assembly using the three key
slots. Twisting in clockwise direction and securely
tighten all three screws. (Figure 6).

7. Route wires through motor coupling cover, canopy
screw cover and canopy (Figure 7).

Fan Motor
Assembly

Housing Ring
Assembly

Figure 5Figure 6

Black, Blue &
White Leads

Canopy

Canopy Screw
Cover

8. Reinstall the hanger ball on the downrod as
follows.Route the three 80-inch wires through the
hanger ball. Position the pin through the two holes
in the downrod and align the hanger ball so the pin
is captured in the groove in the top of the hanger
ball. Pull the hanger ball up tight against the pin.
Securely tighten the set screw in the hanger ball.
A loose set screw could create fan wobble (Figure 8).

9. Cut off excess lead wire approximately 6 to 9
inches above top of the top of the downrod. Strip

insulation off 1/2-inch from the end of each lead

wire (Figure 9).

Set Screw

Motor Coupling
Cover

Figure 7

Black, Blue &
White Leads

Hanger Ball

Canopy

Downrod

Figure 8

NOTE:

where necessary, before installation.

All set screws must be checked, and retightened

Downrod

Figure 9

7

How to Hang Your Ceiling Fan

▲

WARNING

To avoid possible electrical shock, be sure electricity is
turned off at the main fuse box before hanging.

NOTE: If you are not sure if the outlet box is grounded,
contact a licensed electrician for advice, as it must be
grounded for safe operation.

▲

WARNING

The fan must be hung with at least 7´ of clearance from
floor to blades (Figure 1)

▲

WARNING

The outlet box must be securely anchored and capable
of withstanding a load of at least 50 lbs. Hanger bracket
must seat
recessed, remove wallboard until bracket contacts box.
If bracket and/or outlet box are not securely attached,
the fan could wobble or fall.

firmly against outlet box.

If the outlet box is

Ceiling

No

less than

7 ft

Floor

Figure 1

Outlet Box

1. Securely attach the hanger bracket to the outlet box
using the outlet box screws and washers supplied with the
outlet box (Figure 2).

NOTE: Outlet box screws pass through slotted holes of
the hanger bracket (Figure 2).

2. Pull the electric wires in the outlet box down through
the opening in the hanger bracket and bend wires up and
out of the way so that the hanger ball will easily fit into the
hanger bracket.

3. Carefully lift the fan and seat the downrod/hanger ball
assembly on the hanger bracket that was just attached to
the outlet box (Figure 3). Be sure the groove in the ball is
lined up with tab on the hanger bracket (Figure 2).

4. After splicing, the wiring should be turned upward and
pushed carefully up into the outlet box.

▲

WARNING

Failure to seat tab in groove could cause damage to
electrical wires and possible shock or fire hazard.

Hanger

Bracket

Screw (2)

Supplied with

Outlet Box

Hanger

Bracket

Tab

Figure 2

Outlet Box

▲

WARNING

To avoid possible shock, do not pinch wires between the
downrod/hanger ball assembly and the hanger bracket.

Downrod/Hanger
Ball Assembly

Figure 3

8

How to Wire Your Ceiling Fan

WARNING

To avoid possible electrical shock, be sure electricity
is turned off at the main fuse box before hanging
(Figure 1).

NOTE:

If you are not sure if the outlet box is
grounded, contact a licensed electrician for advice, as
it must be grounded for safe operation.

NOTE:

The hand-held remote included with this fan
has 16 different code combinations. To prevent
possible interference from or to other remote units,
simply change the combination code in your
transmitter and receiver.

1. To set the transmitter code, remove battery cover
by pressing firmly below arrow and sliding cover
off. Slide code switches to your choice of up or
down position. Factory setting is all up. Do not use
this position. With a small screwdriver or ball point
pen slide firmly up or down. Replace battery cover
on the transmitter (Figure 2).

2. To set the receiver unit code, slide code switches
to the same positions as set on your transmitter
(Figure 3).

REMOTE
TRANSMITTER
UNIT DETAIL

RECEIVER
UNIT
DETAIL

MAIN FUSE BOX

Figure 1

TRANSMITTER CODES

Figure 2

3. Slide the receiver unit into the open end of the

hanger bracket (Figure 4).

Figure 3

RECEIVER UNIT

HANGER BRACKET

Figure 4

9

How to Wire Your Ceiling Fan (continued)

4. Connect green wires from hanger bracket and
hanger ball to bare (ground) wire using wire
connector supplied. Connect black wire from
receiver unit marked “AC IN L” to black supply wire
using wire connector supplied. Connect white wire
from receiver unit marked “AC IN N” to white supply
wire using wire connector supplied. Connect white
wire from receiver unit marked “TO MOTOR N” to
white wire from fan using wire connector supplied
with receiver. Connect black wire from receiver unit
marked “TO MOTOR L” to black wire from fan

using wire connector supplied. Lastly, connect blue
wire from receiver to the blue fan light wire using
wire connector supplied. Position all connected
wires and receiver antenna to allow installation of
ceiling canopy (Figure 5).

Figure 5

HARDWARE USED:

5. After connections have been made, turn leads
upward and carefully push leads into the outlet box,
with the white and green leads to one side of the
box and the black leads towards the other side.
The wires should be spread apart with the grounded

conductor and the equipment-grounding conductor
on one side of the outlet box and the ungrounded
conductor on the other side of the outlet box
(Figure 6).

Installing the Canopy Housing

NOTE: This step is applicable after the necessary wiring
is completed.

▲

WARNING

To avoid possible fire or shock, make sure that the
electrical wires are completely inside the canopy housing
and not pinched between the housing and the ceiling.

LISTED
OUTLET BOX

BLACK-ANT

CONNECTORS

Figure 6

x 6WIRE

WHITE

BLACK

BLUE

GREEN - Ground Wire
From Hanger Ball

GREEN - Ground Wire From
Hanger Bracket

1. Remove one of the two shoulder screws in the
hanger bracket. Loosen the second shoulder screw
without fully removing it. Assemble canopy by
rotating key slot in canopy over shoulder screw in
hanger bracket. Tighten shoulder screw. Fully
assemble and tighten second shoulder screw that
was previously removed (Figure 1a).

2. Securely attach and tighten the canopy screw cover
over the shoulder screws in the hanger bracket utilizing
the keyslot twist-lock feature (Figure 1b).

Figure 1a Figure 1b

10

How to Assemble the Blades and Light Kit

1. Position the blade over the blade holder with
threaded posts showing. Make sure the bottom
edge of the blade is fully seated against the blade
arm. With a Phillips screwdriver, tighten 3/16-24x

7.5 mm washer head screws and fiber washers to
secure the blade to the blade arm (Figure 1).

3/16-24 x 7.5 mm WASHER
HEAD SCREW AND FIBER
WASHER (3 each per blade)

CAUTION

Do not connect fan blades until the fan is completely
installed. Installing the fan with blades assembled
may result in damage to the fan blades.

2. Secure the blade holders to the motor assembly

using the 1/4-20x14 mm screws (Figure 2).

NOTE:

Periodically check blade holder hardware and

resecure if necessary.

!

WARNING

To reduce the risk of personal injury, do not bend the
blade holders when installing, balancing the blades
or cleaning the fan. Do not insert foreign objects in
between the rotating blades.

CAUTION

To reduce the risk of electric shock, disconnect the
electrical supply circult to the fan before installing
light kit.

Blade holder

Motor
Assembly

Blade

Figure 1

HARDWARE USED:

3/16-24 x 7.5 mm
WASHER HEAD
SCREWS

FIBER WASHER

1/4-20 x 14 mm SCREWS
(2 per assembly)

Blade Holder

Figure 2

HARDWARE USED:

1/4-20 x 14 mm
SCREWS

x 15

x 15

x 10

3. Connect the 2 single pin connector from the socket
plate assembly to 2 single pin connector from motor

assembly (Figure 3).

11

Socket Plate
Single Pin
Connector

Figure 3

Motor Assembly
Single Pin Connector

Socket Plate
Assembly

How to Assemble the Blades and Light Kit (continued)

4. Remove one of the three screws in the light plate
assembly. Slightly loosen the remaining two screws.

Assemble the socket plate assembly to the light plate
assembly using the two key slots. Replace the third
screw and securely tighten all three screws
(Figure 4).

Socket Plate
Assembly

5. Insert light bulb into socket (Figure 5).

CAUTION

To reduce the risk of fire, use 100-watt max. type
T4-minican JD E11 tungsten halogen bulb. Turn off
the wall switch and allow the bulb to cool for 10
minutes before relamping.
Bulb is pressurized and may shatter. DO NOT
TOUCH BULB WITH BARE HANDS. Fingerprints
may result in shorter bulb life. Remove fingerprints
with alcohol prior to use.

6. Remove the three trim screws of support bracket
from the housing ring assembly. Retain the
screws for reinstallation in next step (Figure 6).

Light Plate
Assembly

100-WATT
Minican
Light Bulb (1)

Screws (3)

Figure 4

Socket Plate
Assembly

Figure 5

7. Assemble the glass assembly to the housing ring
assembly using the previous trim screws (Figure 7).

12

Housing Ring
Assembly

Figure 6

Figure 7

Housing Ring
Assembly

Glass
Assembly

Trim
Screws (3)

Trim
Screws (3)