Falltech 7275 User's Instruction Manual For The Installation

USER’S INSTRUCTION MANUAL FOR THE INSTALLATION,

OPERATION & MAINTENANCE OF THE

FALLTECH 7275 6’ to 11’ ADJUSTABLE TRIPOD

WARNING

This is a design compatible component for a comprehensive FallTech personal fall arrest, work positioning or
rescue and evacuation system. Each component includes an instruction manual. These instructions must be
provided to the user of this equipment prior to use. AS A USER, YOU MUST READ, UNDERSTAND AND
FOLLOW THE MANUFACTURER’S INSTRUCTIONS, LABELS AND WARNINGS for each component
part of the complete system before using it. If you do not understand the instructions, labels and warnings for
the use and maintenance of this component, have them explained to you. ANY MISUSE OF THIS
COMPONENT, ANY ALTERATION OR MODIFICATION OF IT, OR FAILURE TO PROPERLY FOLLOW
THESE USER’S INSTRUCTIONS, MAY RESULT IN SERIOUS INJURY OR DEATH.

If any additional information is required to use this product, it will be supplied with this product. Fall arrest
equipment used in conjunction with the FallTech 7275 Adjustable Tripod will also be supplied with
instructions.

This manual is intended to meet industry standards, including OSHA 1910.146 and ANSI Z117.1 and should be
used as part of an employee training program. It should be read completely and used as part of the User’s
Training Program as required by OSHA (1910.66, Appendix C).

1.0 PRODUCT DESCRIPTION AND APPLICATIONS

FALLTECH Part Number: 7275 Adjustable Tripod

The FallTech 7275 Adjustable Tripod is designed to be used in applications where a fall hazard exists, but there
is no means of arresting a fall. The FallTech Tripod is designed to be part a comprehensive confined space
entry, retrieval, and rescue system. It provides a portable anchorage for a variety of different systems, such as
those available from FallTech. The tripod collapses down to 6 feet and can extend can extend to an overall
height of 11 feet. The telescoping legs have adjustment holes 5 inches. A built-in pulley at the head provides
smooth travel for the primary retrieval line. Additionally, three side mount anchor points are provided for
accessory pulleys and lifeline. The feet are shaped with a large point at one end, allowing the tripod to be driven
into loose ground surfaces for more stability. Three retention pins located at the head allow the legs to be locked
in place after set-up. A retention web assembly is looped through the feet to keep the legs from legs from
splaying out under extreme load. The legs are extruded and aluminum and anodized for protection. The tripod is
rated for 5,000 pounds as an anchorage connector.

This system has been designed and tested to be used with FallTech Personal Fall Arrest Equipment (PFAS)
only. It has been designed for personal fall arrest, material handling, work positioning or confined space rescue
and evacuation.

The following limitations must be considered when planning to use this product. Failure to do so may result in
serious injury or death:

• The FallTech 7275 Adjustable Tripod must be properly installed following the guidelines set forth in

Section 6.0

• The maximum working load for this Tripod is 310lbs

• PFAS used with this Tripod must meet applicable federal and state regulations set forth in Section 6.1

In addition to the above limitations, the following environmental and physical factors must also be considered
prior to use:

• High heat (metal cutting or welding slag)

• Sharp edges

• Electrical lines

• Caustic chemicals

• Corrosive environment (seawater)

Contact FallTech for any questions regarding applications of this equipment in areas where environmental or
physical hazards exist.

2.0 PRODUCT DESCRIPTION AND APPLICATIONS

2.0 PRODUCT SPECIFICATIONS

Material of Construction Aluminum.
Diameter of Opening at 6 ft 51.5” between legs
Diameter of Opening at 11 ft 51.5” between legs
Leg Height Adjustment Increm ents 5 inches
Max Working Load-Personnel 310 lbs. (including tools)
Safe Working Loa d 800 lbs.

3.0 SYSTEM REQUIREMENTS

Anchorages
Anchorage points used for Personal Fall Arrest Systems must be designed to meet the requirements set forth by
ANSI Z359.1-1992, section 7.2.3, which is consistent with OSHA 1910.66 Appendix C. Anchorages must have
strength capable of supporting static loads, applied in the direction permitted by the PFAS, of at least:

(a) 3,600 lbs. when certification exists; or
(b) 5,000 lbs. in the absence of certification

If more than one personal fall arrest system is attached to an anchorage, the anchorage strengths set forth in (a)
and (b) of this section must be multiplied by the number personal fall arrest systems attached to the anchorage.

Compatibility of System
The FALLTECH Permanent Horizontal Lifeline System has been designed to be used only with FALLTECH
approved components. If FALLTECH equipment is used with other fall arrest equipment that is not compatible,
the integrity of the system may be jeopardized. If you have questions concerning equipment compatibility,
please contact your local field representative or FALLTECH at [phone].

Limitations Of System

System Capacity – 7275 6’ to 11’ Adjustable Tripod has a maximum capacity of three workers. There must
also be adequate clearance beneath the walking/working surface (see section titled clearance below) for the
system to function properly. The maximum worker’s weight, including tools, cannot exceed 310 pounds.
Consult your FALLTECH sales representative if you have any questions concerning your application.

Corrosion – Harsh environments can cause corrosion of metal parts. The Permanent Horizontal Lifeline
System should not be left in corrosive environments for extended periods of time. Additional inspections may
be necessary to verify that the lifeline and components are in good working condition.

Electrical Hazards – User should always use extreme caution when working near electrical sources.

Heat – Do not use this device in extremely high temperatures. When performing any type of metal work, such

as welding, cover fall arrest

Moving Machinery – If it is necessary to work above moving machinery, maintain a safe distance between the
moving parts and yourself, clothing, and personal protective equipment.