How it Works
Falcon
Loading...
EYE-ON 16/16R+
User Manual
133 pgs5.46 Mb0

Falcon EYE-ON 04/08, EYE-ON 16/16R+ User Manual

1
Digital Video Recorder
User’s Manual
EYE-ON 04 / 08 / 16 / 16R+
2
Thank you for using our product.
1. This is user's manual for H.264 HD DVR (Digital Video Recorder).
3. Contents in this manual may be changed according to the specification change and feature improvement without any notification.
4. This user's manual shall never be copied without prior agreement and violating this may be a reason for legal punishment on piracy.
5. If there is any incorrect or insufficient content in this user's manual, notify it to Customer Support Center.
3
CONTENTS
Contents
CH 1. Product Introduction`
1-1. Product Contents 5 1-2. Specifications 7 1-3. Product Characteristics 11 1-4. Name of Each Part 13
CH 2. Installation Guide and Cautions
2-1. Cautions 19 2-2. Product Installation 22
2-2-1. Power Connection 22 2-2-2. Connecting External Device 22
CH 3. How to Use
3-1. General Usage Information 26
3-2. Live Mode 27
3-2-1. Live mode control 27 3-2-2. Live mode feature 29
3-3. Search Mode 35
3-3-1. Search selection type 35 3-3-2. Play Mode 39
3-4. Setup Mode 40
3-4-1. Display 40 3-4-2. Record 45 3-4-3. Device 50 3-4-4. Network 65 3-4-5. System 72
3-5. Firmware Upgrade 78
4
CONTENTS
Trouble Shooting 80
Warranty 81
Appendix A CMS(Client Management Software) 82
Appendix B Catcheye for Android mobile 120
Appendix C Catcheye for iPhone 126
Contents
5
1-1. Product Contents(EYE-ON 04/08)
After removing packing materials of this product, check whether all following contents are included.
CH1. Product Introduction
CH 1 Product Introduction
Main Body (DVR):
This converts the analog video and audio signal to the digital signal and saves on HDD.
Adapter:
This 12V adapter supplies power to the product.
Power Cable:
This connect the adapter and the power source.
Program CD:
This contains the User’s manual and Client Program for DVR.
Remote Controller:
This is an IR remote controller for convenience.
Battery:
These are 2(two) battery for the remote controller.
6
1-1. Product Contents(EYE-ON 16R/16R+)
After removing packing materials of this product, check whether all following contents are included.
CH 1 Product Introduction
Main Body (DVR):
This converts the analog video and audio signal to the digital signal and saves on HDD.
Adapter:
This 12V adapter supplies power to the product.
Power Cable:
This connect the adapter and the power source.
Program CD:
This contains the User’s manual and Client Program for DVR.
Remote Controller:
This is an IR remote controller for convenience.
Battery:
These are 2(two) battery for the remote controller.
7
1-2. Specifications (HD-SDI)
CH 1 Product Introduction
Model
EYE-ON HD SDI
HD04 HD08 HD16R
Description HD-SDI only 1080p real time DVR
Video
Camera input
4 BNC 8 BNC 16 BNC
Individual HD/Analog sel
ectable
HD-SDI
Available source
720p25,30,50,60/1080p25,30,50,60/1080i50,60/Mixed
Output
1 HDMI+1 VGA (simultaneously) / 1 Programmable SPOT with OSD
Audio
Audio input
4 RCA 16 RCA
Output
1 RCA
Sensor In
4 (NC, NO selectable) 16(NC, NO selectable)
Alarm out
1 relay 14 TTL, 2 relay
Operating System
Embedded Linux OS
Display
Speed
Real Time
Resolution (Pixel)
1280X1024, 1280X720, 1920X1080
Split screen
1,4 1,4,6,8,9 1,4,6,8,9,13,16
Recording
CODEC
H.264 / JPEG for 3G, Dual CODEC
Resolution (Pixel)
720p, 1080p,1080i, 960H, 720H, Mixed
Picture quality
4 steps (Super, High, Medium, Low)
Speed
NTSC area
PAL area
120fps@1080p 100fps@1080p
240fps@1080p 200fps@1080p
480fps@1080p 400fps@1080p
Playback
Display
1,4 1,4,8 1,4,6,8,9,13,16
Search mode
Calendar, Event ,POS , Panorama, Thumbnail
Speed
NTSC
PAL
60fps@1080p
100fps@1080p
120fps@1080p 200fps@1080p
120fps@1080p 200fps@1080p
Fast/Slow speed
Normal, REW & FF [recorded speed x2, x4, x8, x16,x32,x64,x1/2,x1/4], Frame to
frame, Pause
8
Model
EYE-ON HD SDI
HD04 HD08 HD16R
Network
Network Interface
Gigabit Ethernet
Speed
15fps@1080p 60fps@1080p 120fps@1080p
Protocol
TCP/IP, HTTP, DHCP
Application
Windows 2000 / XP / 7 / 8 (PC Client system& IE)/MAC
Web Browser
Internet Explorer, Safari, Chrome, Firefox
Smart phone App
Android, iPhone for live and search
Backup
Interface
USB 2.0 X 2 USB 2.0 X 3
Backup device
External HDD, CD&DVD-RW, Network, Thumb Drive
The number of HDD
2 SATA(No capacity limit ; 4TB of more)
4 SATA + 1
eSATA (
upto
12 bays, No capacity limit
; 4TB or more)
1-2. Specifications (HD-SDI, continued)
CH 1 Product Introduction
9
Model
EYE-ON ALL HYBRID
04 08 16R 16R+
Description
Hybrid(HD-SDI, Analog) 1080p real time DVR
Video
Camera input
4 BNC 8 BNC 16 BNC 16 BNC
Individual HD/
Analog selectable
All Hybrid(Patent)
Available source
720p25,30,50,60/1080p25,30,50,60/1080i50,60/Composite/960H/Mixed
Output
1 HDMI+1 VGA (simultaneously) / 1 Programmable SPOT with OSD
Audio
Audio input
4 RCA 16 RCA
Output
1 RCA
Sensor In
4 (NC, NO selectable) 16(NC, NO selectable)
Alarm out
1 relay 14 TTL, 2 relay
Operating System
Embedded Linux OS
Display
Speed
Real Time
Resolution (Pixel)
1280X1024, 1280X720, 1920X1080
Split screen
1,4 1,4,6,8,9 1,4,6,8,9,13,16
Recording
CODEC
H.264 / JPEG for 3G, Dual CODEC
Resolution (Pixel)
720p, 1080p,1080i, 960H, 720H, Mixed
Picture quality
4 steps (Super, High, Medium, Low)
Speed
NTSC area
PAL area
120fps@1080p 100fps@1080p
240fps@1080p 200fps@1080p
480fps@1080p 400fps@1080p
480fps@1080p 400fps@1080p
Playback
Display
1,4 1,4,8 1,4,6,8,9,13,16
Search mode
Calendar, Event ,POS , Panorama, Thumbnail
Speed
NTSC
PAL
60fps@1080p
100fps@1080p
120fps@1080p 200fps@1080p
120fps@1080p 200fps@1080p
480fps@1080p 400fps@1080p
Fast/Slow speed
Normal, REW & FF [recorded speed x2, x4, x8, x16,x32,x64,x1/2,x1/4], Frame to
frame, Pause
1-2. Specifications (ALL HYBRID)
CH 1 Product Introduction
10
1-2. Specifications (ALL HYBRID, continued)
CH 1 Product Introduction
Model
EYE-ON ALL HYBRID
04 08 16R 16R+
Network
Network Interface
Gigabit Ethernet
Speed
15fps@1080p 60fps@1080p 120fps@1080p
Protocol
TCP/IP, HTTP, DHCP
Application
Windows 2000 / XP / 7 / 8 (PC Client system& IE)/MAC
Web Browser
Internet Explorer, Safari, Chrome, Firefox
Smart phone App
Android, iPhone for live and search
Backup
Interface
USB 2.0 X 2 USB 2.0 X 3
Backup device
External HDD, CD&DVD-RW, Network, Thumb Drive
The number of HDD
2 SATA(No capacity limit ;
4TB of more)
4 SATA + 1 eSATA (upto 12 bays,
No capacity limit ; 4TB or more)
11
1-3. Product Characteristics
1) Full HD real time and All Hybrid
This DVR can record HD and Full HD video with extreme quality. Also it displays real HD(1920X1080) resolution, and therefore it provides the most clear image quality and the best security level. Furthermore, EYE-ON series can mix any input such as analog, 960H and HD-SDI. All video input is detected automatically. (Patent)
2) High reliability
With Embedded hardware and software design, this maintains higher product reliability.
3) Simple usage
This allows users to use it conveniently by placing control buttons similar to existing
ones on VCR, and users can easily learn the usage.
4) Pentaplex System
Pentaplex System allows live, recording, backup, networking and playback simultaneously.
5) Selectable recording setup
For recording methods, users can select the frame rate, resolution and video quality individually in order to be appropriate for user's environment.
6) Remote monitoring
With using exclusive line or Internet network, you can search or monitor recorded images remotely by installing exclusive client program on Windows PC or Mac.
7) Backup
You can backup with a versatile external USB devices.
8) Audio recording
You can record 4 sound inputs simultaneously. Moreover, you can listen to the sound in search and live monitoring and play mode.
9) Various recording methods
This provides convenient use with manual recording, recording by dates and days, hourly schedule recording, sensor and motion detection event recording and others to enable unmanned monitoring.
10) Various total monitoring features
You can cover any security scenario through various sensor inputs and contact output control.
CH 1 Product Introduction
12
11) Display information in easy-to-understand information method
This enhanced convenience of user by displaying information (date, time, recording method, recording frame number, HDD capacity and others) in monitoring, recording and playing mode in easy-to-understand way.
12) P/T/Z control
By built in RS485, various P/T/Z cameras can be used.
13) Dual CODEC for video transmission
DVR can send 120 fps (based on CIF) regardless of the local recording and viewing setup regardless with recording setup.
14) Web browser support
You can monitor and playback the video and control the PTZ camera by internet explorer.
15) Built in S.M.A.R.T.
You can automatically check the health of the hard disk drives.
16) Language pack
Basically DVR has multiple language set, furthermore you can choose the language set if you want.
17) Mirroring by internal HDD
If you install two HDDs, you can use the second HDD for backup for maximum fault tolerance.
18) Spot monitoring
Spot out can be enable to monitor sequentially in other place.
19) Touch LED Switch
You can operate with touch LED switch in front panel.
20) Text inserter(POS Interface)
You can operate with the POS and ATM.
21) HD Spot out
You can use one of VGA and HDMI to the HD spot.
CH 1 Product Introduction
13
1-4. Name of Each Part
[Front Panel]
CH 1 Product Introduction
<EYE-ON 04/08>
1. USB ports : These USB ports are for mouse and USB devices. You should
connect correctly the USB devices and mouse as picture directed.
2. Status lamps
POWER : Blue color back light. Power indicator. RECORD : Red. Indicate the recording. NETWORK : Green. Lit on connecting the network
3. Function keys
1) MENU : It will move to the setup screen from the live mode.
2) SEARCH : It will change to the playback mode from the live mode.
3) BACKUP : It will move to the backup screen from the live or play mode.
8. Number buttons : If you press this button, it will be changed to full screen in live
viewing or playback If you want to go to 20ch, push the 10+ button twice.
(※ In menu and password setting, it is automatically converted to number buttons)
5. IR RECEIVER : It is for remote controller.
14
[Front Panel]
CH 1 Product Introduction
< EYE-ON 16R/16R+>
1. Playback buttons : It will be used on playback. If you press these buttons in live
mode, it will be automatically changed to the Instant Play mode. ‘Stop’ button changes from the play mode to the live mode.
2. ARROW, ENTER : This button is used to change settings for the product in
MENU Mode or used in Search Mode.
3. Function keys
1) MENU : It will move to the setup screen from the live mode.
2) SEARCH : It will change to the playback mode from the live mode.
3) BACKUP : It will move to the backup screen from the live or play mode.
4) DISPLAY : It will change the screen splitting sequentially from 1 to 20. It can be adapted both live and play mode.
5) SWITCHING : It will change to switching mode except 20 splitting.
6) ZOOM : It will go to the digital zoom directly.
7) PTZ : It will change to the pan, tilt and zoom control mode from the live mode.
8) LOCK/EXIT : If you want move to the upper menu or exit without saving, press
this button. On playback, it will disappear the search list for the better viewing. On live viewing, it performs the system lock.
9) PANIC : This button is used in emergency status. If you push this button,
the DVR starts to record with maximum speed regardless of setting value.
4. Status lamps
POWER : Blue color back light. Power indicator. RECORD : Red. Indicate the recording. NETWORK : Green. Lit on connecting the network ALARM : Red. It will be lit on when the events happen
5. USB ports : These USB ports are for mouse and USB devices.
6. IR Window : the window for remote controller
15
CH 1 Product Introduction
1. Cooling Fan
2. Video In: This receives images from SDI cameras(04) or any camera(08).
3. LAN Port: This is the Gigabit Ethernet LAN cable connection terminal.
4. SPOT Out : To CRT 4:3 monitor for spot video.
5. VGA port: video output for analog RGB display
6. DC Power : DC12V 4.16A or up
7. RS485 port : For control the pan and tile cameras. Make sure that the polarity.
8. Relay out : This terminal blocks connect external electric devices to the product
( Warning Lamp and others).
9. Sensor In : This terminals can be connected to external sensors.
10. Audio In: RCA audio in terminals. You can record four channels at the same
time.
11. Audio Out: RCA audio out terminal.
12. HDMI : HDMI output for HD monitor
13. VGA Extender (option) : Connect EXTEND FTP cable to Receiver
※
For more details, refer to [CH 2. Installation Method and Cautions].
[Rear Panel]
< EYE-ON 04>
1.FAN
2.VIDEO IN
3. LAN
4.SPOT
5. VGA
12.HDMI
6. POWER
11.AUDIO OUT
8.RELAY
7.RS485
10. AUDIO IN
9.SENSOR IN
13.Xbox
Extender
(option)
7. Number buttons : If you press this button, it will be changed to full screen in live viewing or playback. Also 10+ button is used for ‘Hold’ while Jog Shuttle action.
(※ In menu and password setting, it is automatically converted to number buttons)
8. Backup device : You can use the versatile backup devices such as CD-RW and DVD-RW.
16
CH 1 Product Introduction
1. Cooling Fan
2. Video In: This receives images from analog/960H/SDI cameras.
3. LAN Port: This is the Gigabit Ethernet LAN cable connection terminal.
4. SPOT Out : To CRT 4:3 monitor for spot video.
5. VGA port: video output for analog RGB display
6. DC Power : DC12V 4.16A or up
7. RS485 port : For control the pan and tile cameras. Make sure that the polarity.
8. Relay out : This terminal blocks connect external electric devices to the product
( Warning Lamp and others).
9. Sensor In : This terminals can be connected to external sensors.
10. Audio In: RCA audio in terminals. You can record four channels at the same
time.
11. Audio Out: RCA audio out terminal.
12. HDMI : HDMI output for HD monitor
13. VGA Extender (option) : Connect EXTEND FTP cable to Receiver
※
For more details, refer to [CH 2. Installation Method and Cautions].
[Rear Panel]
< EYE-ON 08>
1.FAN
2.VIDEO IN
3. LAN
4.SPOT
5. VGA
12.HDMI
6. POWER
11.AUDIO OUT
8.RELAY
7.RS485
10. AUDIO IN
9.SENSOR IN
13.Xbox
Extender
(option)
17
1. Video In : This receives images from cameras and sends them to monitors. Loop Out : This sends the images from the cameras to the other devices.
2. Audio Out : RCA audio out terminal.
3. Power Switch
4. Adapter : Connect DC12V only.
5. RS232C : This is Serial communication(RS232C) cable connection terminal.
6. e-SATA
7. LAN Port: This is LAN cable connection terminal.
8. USB ports : This USB port is for mouse and USB devices.
9. Audio In: RCA audio in terminals. You can record 16 channels at the same
time.
10. HD Out : Real HD(1920X1080) output for high resolution monitor
11. VGA port: video output for VGA display
12. Sensor, Alarm, RS485 : For external sensor and external electric devices to
these terminal block. There are 16 inputs, 2 relay output and 14 TTL output. For control the pan and tile cameras. Make sure that the polarity.
13. VGA Extend (option) : Connect EXTEND FTP cable to Receiver
14. Spot Out : For spot CRT monitor, composite signal comes out.
※
For more details, refer to [CH 2. Installation Method and Cautions].
CH 1 Product Introduction
[Rear Panel]
< EYE-ON 16R/16R+>
12. Sensor, Alarm, RS485
1.Video In
7. LAN
6. e-SATA
11. VGA
10.HD Out
3. Switch
14.Spot Out
13. Extend
5. RS232C
9. Audio In
4.Adapter
8. USB
2.Audio Out
18
2-1. Cautions
- Avoid installing the product where there are direct rays or it is hot by locating near
from heat generator. (May cause fire)
- Do not put vase, flowerpot, cup, cosmetics, drug, and anything the contain water on
product. (May cause fire or electric shock, and it may injure people by falling)
- Do not insert or drop any metal object (coin, hair pin) or flammable object (match,
paper) into air hole. (May cause fire or electric shock)
- Do not put any heavy object on it. (May injure people by being fell or destroyed.)
- Put power plug surely not to be moved. (If not, this may cause fire.)
- Unplug power plug and antenna when there are thunders and lightening. (May
cause fire.)
- For cleaning the product, wipe surface with dry towel. Using chemical agent or
cleaner may change the color and unpeel paint. Do not put several plugs at same time. (May cause electric shock.) If there is smoke or strange smell, stop operation. In this case, turn the power off and unplug it, and then contact our service center. (If you keep using it, this may cause fire or electric shock.)
- Do not unplug by pulling cord. (If cord is damaged, it may cause fire or electric
shock.)
- Do not plug or unplug with wet hands. (May cause electric shock.)
CH2. Installation Method and Cautions
CH 2 Installation Method and Cautions
WARNING
Risk of electric shock.
Do not open the cover of the product.
Servicing of this product by unauthorized personnel is
prohibited and will result in a void of warranty.
In order to ensure the most stable
conditions for power, the use of a UPS (Uninterrupted
Power Supply) is recommended.
19
- Keep the power cord untwisted. (May cause fire or electric shock.)
- Use proper adapter. (Using too much electric power may cause fire or electric shock.)
- Do not install it at where exposed to rain and wind and water drop. (May cause fire,
electric shock and transformation.)
- Keep away from fire. (May cause fire.)
-Do not disassemble or remodel on your own. (May cause malfunction or electric
shock.)
- Do not put next to flammable materials like flammable spray. (May cause fire.)
- Do not install it at a place with too much dirt. (May cause fire.)
- Do not install it on unstable places like shaking table and inclined place or shaking
place. (May injure users by falling down or being upside down.)
- Do not put an heavy object on power cord or avoid it from being pressed by the
device. (May cause fire or electric shock.)
- In case of using extension cord, do not use several devices at same time. (May cause
fire with abnormal heating of extension.)
- When there are dirt on power plug pin or power outlet, clean it nicely. (May cause
fire.)
-Do not damage on power cord or plug, and bend or twist or pull too much, and put it
between other objects or heat. If power outlet insertion part is not tight, do not use it. (May cause fire or electric shock.)
-Do not drop or give a shock to the product. (May injure people or cause malfunction.)
- Do not touch power adaptor or signal controller. (May cause electric shock.)
- Do not put any object too close to block cooling fan. (May cause fire.)
- In case of exchanging batteries with improper type, there might be danger of
explosion.
- For used batteries, throw away separately from other garbage.
- When you take out batteries, avoid children from eating them by mistake. Keep them
away from children. (If a child ate them, contact a doctor right away.)
CH 2 Installation Method and Cautions
20
CH 2 Installation Method and Cautions
Note :
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made.
This device complies with the part 15 of the FCC Rules. Operation is subject to the following two conditions : (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operations.
FCC Warning :
This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made.
CE Warning : This is a Class A product. In a domestic environment this may cause radio interference in which case the user may be required to take adequate measures.
This product has obtained EMI registration.
21
2-2 Product Installation
This product may be composed of camera and monitor in default, and additionally the sensor, microphone, speaker and PC for network can be connected if necessary.
2-2-1. Power Connection
1) Connect adapter cable to power connection terminal at rear side.
2) Input AC power to the adapter. (free voltage from 100V to 240V, 50/60Hz)
※ You must operate it at the rated voltage instructed on the user's manual. In case power higher than the rated voltage is supplied, it may cause damages on product.
2-2-2. Connecting External Device
CH 2 Installation Method and Cautions
※ Connect it when power of the product is off. ※ Read through user's manual for the device you are connecting carefully.
1) How to Connect External Video/Audio Device
Connect cameras to VIDEO IN by channels. Connect microphone (AMP) to AUDIO IN by channels. Connect VIDEO OUT to VIDEO IN of monitor. Connect HD output to HD Monitor. Connect AUDIO OUT to AUDIO IN of monitor (or speaker). Connect Spot output to Composite Monitor.
CAMERA
MIC
22
v Read this notice before connecting HD-SDI cameras.
You cannot mix NTSC and PAL cameras with DVR products.
1. Please check the type(NTSC or PAL) of cameras.
NTSC : 30fps, 60fps PAL : 25fps, 50fps
• You can see the cameras connected with DVR on Device menu.
* The figure above shows that the camera is 1080P 30fps (NTSC).
2. Change camera type that you want to use on your camera.
• You can choose the type from setting fps on HD-SDI cameras.
(This DVR does not support setting manual fps.)
• For more details, refer to user’s manual of the related HD-SDI Camera.
CH 2 Installation Method and Cautions
23
CH 2 Installation Method and Cautions
2) How to connect external sensor
Sensor terminal is composed of 1 input channel and 1 output channel. Sensor out terminal is relay output with 1A, 24V or 0.5A,125V.
SIREN
POWER
- +
SENSOR
Sensor In : Connect the sensors. The sensor are composed of both signal and ground terminals, with a voltage difference of 5V. In the case that the sensor used for input is of the N/O (Normal Open) type, when the voltage difference between the signal and ground falls to 0V (short), the DVR can use this as a trigger to start alarm/sensor based recording. Sensor Out : Connecting external electrical devices The relay output terminal does not provide power, and functions only on an ON/OFF basis via a relay. Normally, the signal and ground should be on an OPEN basis, and the DVR will complete the relay connection.
3) Connecting with PC using LAN cable
If you want to connect DVR to PC directly, use LAN cable, and if you want to use HUB, connect cable via hub.
*Hub : This is a device connecting one office to devices located near with using
cable when you organize LAN
*Cable : This is standard UTP cable used for communication among
devices through Hub and others when you organize LAN
PC
HUB
24
CH 2 Installation Method and Cautions
4) Connection Using PTZ camera
In case of using pan and tilt cameras, connect PAN/TILT DRIVE to product as shown at following figure.
RS485 CABLE
VIDEO CABLE
SPEED
DOME
5) Installing Hard disk drive
In case of installing the hard disk drive, open the upper case and install the hard disk drive on the hard bracket. Remember that the main power should be off to install the hard disk drive. If you have any trouble, please contact the technical support.
25
3-1. General Usage Information
The EYE-ON series can be operated with a mouse or remote controller under the four main modes listed below:
Live Mode – This is the “main or default” mode. From this mode you can view in real time all currently operating cameras, information regarding camera status, and have access to Pan/Tilt camera controls. In addition, system status information will be shown during live mode, and other modes can be entered from Live mode.
Setup Mode – The user will be able to customize settings for Live viewing, Recording, Backup, and Camera related devices under the Setup Mode.
Search Mode – In Search Mode, the user will be able to review all recorded footage in the case that an event must be reviewed using a calendar or event based search.
Backup Mode – In Backup Mode, the user will be able to archive the desired data to the preferred supported media of their choice (ex. CD, DVD, USB Backup, Remote Client Software, etc.)
Password Protection – The DVR system will utilize a user ID and password system to prevent unauthorized usage of this product. Control of the system will only be possible after entering a proper ID and password as illustrated below. (Factory Default settings are blank for these fields).
IDs and passwords should be managed by a system administrator, as different users may be given different levels of access to the DVR.
CH3. How to Use
CH 3 How to Use
26
3-2. LIVE Mode
In this section you will know how to split the video mode into 1, 4, 6, 8, 9, 12, 16, as well as auto sequencing, PTZ Control, Mouse control, Setup configurations, Backup
CH 3 How to Use
3-2-1. LIVE Mode Control
Recording indicator
Event recording indicator
Motion detection indicator
Sensor activation indicator
POS indicator
1) Live View Status
You may use the Live Menu Bar located at the bottom for quick shortcuts and view status of certain items.
2) Live Menu Bar
You may use the Live Menu Bar located at the bottom for quick shortcuts and view status of certain items.
27
CH 3 How to Use
3) Live Popup Menu
By Right-Clicking anywhere on Live Screen, you may view the Live Popup Menu. By using the Live Popup Menu, you can quickly jump to the necessary configuration and settings.
28
CH 3 How to Use
3-2-2. LIVE Mode Feature
1) Setup : refer to 3-4
2) Split
Change video split mode for Live View.
4) Instant Replay
This is very convenient function to catch the abrupt accident. During live viewing,
you can go directly to the playback screen.
If you choose the ‘Instant Replay’ , the DVR goes to the ‘PLAY’ with the present
time screen. And you can use the functions related playback.
3) Audio Out
You can choose the audio out from this menu.
5) Search : refer to 3-3
29
• After that, if you push the ‘Estimation’ button, it will show the estimated backup file size.
6) Backup
There are two ways to enter the backup. The first one is that right click on the live screen, and the second one is that enter directly from ‘Search’ upon playback. If you choose the ‘backup’ from the live menu, below backup screen appears.
CH 3 How to Use
• You can set the backup device, time and channel from the backup screen.
• Then click the ‘Start’ button.
WARNING
Do NOT remove the backup device till end sign. The device
and system may be damaged.
0 MB / 533 MB
30
Preset[Enter] Preset setup
Zoom +/-
You can zoom out/in with mouse or [1]/[2] buttons on the remote controller.
Focus +/-
You can adjust the focus with mouse or [3]/[4] buttons on the remote controller.
IRIS +/-
You can adjust the iris with mouse or [5]/[6] buttons on the remote controller.
v For more details, refer to [CH 2-2. Connection Using PTZ camera] and
[CH 3-4-3. Device].
CH 3 How to Use
7) Snapshot
You can save the live snapshot by this menu. All channel will be saved individually to the USB memory by JPG format . You should put in USB memory before saving.
9) PTZ (Pan, Tilt and Zoom)
It is possible to control the pan and tilt camera by itself. Press the ‘PTZ’ button to enter the PTZ mode. For Menu setting, you can set it by pressing button as displayed at bottom of window.
8) Freeze
You can freeze the current live video channels.
Loading...
+ 103 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use