Falcon CLAS110DFFBL-CH, CLAS110DFFCR-BR, CLAS110DFFCR-CH, CLAS110DFFCY-CH, CLAS110DFFBL-CHLPG Installation and Operation Guide

...

Download

Page 1

USER GUIDE &

INSTALLATION INSTRUCTIONS

Classic 110cm Dual Fuel

Australia

U108600-07

Page 2

Contents

1. Before you Start... 1

Installation and Maintenance 1 Peculiar Smells 1 If You Smell Gas 1 Ventilation 1 Personal Safety 1 Cleaning 2

2. Cooker Overview 3

Hotplate Burners 3 Wok Burner 4 The Wok Cradle 5 The Griddle 5 Warmer 5 The Grill 6 The Ovens 7 Operating the Ovens 7 The Clock 8 Accessories 10 Main Oven Light 10 Storage 10

3. Cooking Tips 11

Tips on Cooking with the Timer 11 General Oven Tips 11

4. Cooking Table 12

7. Installation 19

Service and Spares 19 Dear Installer 20 Provision of Ventilation 20 Location of Cooker 20 Conversion 20 Positioning the Cooker 22 Moving the Cooker 23 Fitting the Stability Bracket and Chain 24 Fitting the Restraining Chain 24 Levelling 24 Pressure Testing 25 Electrical Connection 26 Final Checks 27 Final Fitting 27 Customer Care 27

8. Conversion to Propane Gas 28

Conversion from Natural Gas (1.0 kPa)

to LPG X Propane (2.75 kPa)

Hotplate 28 Grill 28 Ovens 29 Gas Connection 29 Pressure Testing 29 Ax Label 29

5. Cleaning Your Cooker 13

Essential Information 13 Hotplate Burners 13 The Griddle 14 Grill 14 Control Panel and Doors 14 Ovens 15 Cleaning Table 16

6. Troubleshooting 17

9. Servicing 30

Panels 30 Hotplate 31 Controls 32 Grill 33 Ovens 34 Doors 35

10. Circuit Diagram 37

11. Technical Data 38

Page 3

1. Before You Start...

This User Guide covers a number of dierent models. Although some of the illustrations will look dierent to your particular model the functions will be the same. We hope the meaning is clear.

This appliance is designed for domestic cooking



only. Using it for any other purpose could invalidate any warranty or liability claim. In particular, the oven should NOT be used for heating the kitchen – besides invalidating claims this wastes fuel and may overheat the control knobs.

Installation and Maintenance

The installation must be in accordance with the relevant instructions in this booklet, with the relevant national and local regulations, and with the local gas and electricity supply companies’ requirements.

Make sure that the gas supply is turned on and that the cooker is wired in and switched on (the cooker needs electricity).

Set the clock to make sure that the oven is functional – see the relevant section in this manual.

The cooker should be serviced only by a qualied service engineer, and only approved spare parts should be used.

Always allow the cooker to cool and then switch it o at the mains before cleaning or carrying out any maintenance work, unless specied otherwise in this guide.

Peculiar Smells

When you rst use your cooker it may give o an odour. This should stop after use.

Before using for the rst time, make sure that all packing materials have been removed and then, to dispel manufacturing odours, turn the ovens to 200 °C and run for at least an hour.

Make sure the room is well ventilated to the outside air (see ‘Ventilation’ below). People with respiratory or allergy problems should vacate the area for this brief period.

If You Smell Gas

• DO NOT turn electric switches on or off

• DO NOT smoke

• DO NOT use naked flames

• DO turn off the gas at the meter or cylinder

• DO open doors and windows to get rid of the gas

• DO keep people away from the area affected

• Call your gas supplier

Ventilation

CAUTION: The use of a gas cooking appliance results



in the production of heat and moisture in the room in which it is installed. Make sure that the kitchen is well ventilated: keep natural ventilation holes open or install a powered cookerhood that vents outside. If you have several burners on, or use the cooker for a long time, open a window or turn on an extractor fan.

Personal Safety

DO NOT modify this appliance.



This appliance can be used by children aged from



8years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.

WARNING: The appliance and its accessible parts



become hot during use and will retain heat even after you have stopped cooking. Care should be taken to avoid touching heating elements. Children less than 8 years of age shall be kept away unless continuously supervised.

CAUTION: A long term cooking process has to be



supervised from time to time. A short term cooking process has to be supervised continuously.

Danger of re: DO NOT store items on the cooking



surfaces.

To avoid overheating, DO NOT install the cooker



behind a decorative door.

DO NOT use a steam cleaner to clean the cooker.



Accessible parts will become hot during use and



will retain heat even after you have stopped cooking. cooker and never wear loose-tting or hanging clothes when using the appliance.

Always be certain that the controls are in the OFF



position when the oven is not in use, and before attempting to clean the cooker.

When the oven is on, DO NOT leave the oven door



open for longer than necessary – otherwise, the control knobs may become very hot.

Keep babies and children away from the

Page 4

Cooking high moisture content foods can create a ‘steam burst’ when an oven door is opened. When opening the oven stand well back and allow any steam to disperse.

DO NOT use water on grease res and never pick



up a aming pan. Turn the controls o and then smother a aming pan on a surface unit by covering the pan completely with a well tting lid or baking tray. If available, use a multi-purpose dry chemical or foam type re extinguisher.

ArtNo.324-0001 Steam burst

Always keep combustible materials, e.g. curtains,



and ammable liquids a safe distance away from your cooker.

DO NOT store ammable materials in the storage



drawer or near this appliance.

DO NOT spray aerosols in the area of the cooker



while it is on.

Use dry oven gloves when applicable – using damp gloves might result in steam burns when you touch a hot surface. Do not use a towel or other bulky cloth in place of a glove – it might catch re if brought into contact with a hot surface.

NEVER operate the cooker with wet hands.



DO NOT use aluminium foil to cover shelves, linings



or the oven roof.

NEVER heat unopened food containers. Pressure



build up may cause the containers to burst and cause injury.

Take care that no water seeps into the appliance.

Only certain types of glass, glass-ceramic, earthenware or other glazed containers are suitable for hotplate cooking; others may break because of the sudden change in temperature.

This appliance is heavy so take care when moving it.



Cleaning

In the interests of hygiene and safety, the cooker should be kept clean at all times as a build up in fats and other food stu could result in a re.

Clean only the parts listed in this guide.

Clean with caution. If a wet sponge or cloth is used to wipe spills on a hot surface, be careful to avoid steam burns. Some cleaners can produce noxious fumes if applied to a hot surface.

DO NOT use unstable saucepans. Always make sure



that you position the handles away from the edge of the hotplate.

Never leave the hotplate unattended at high heat settings. Pans boiling over can cause smoking, and greasy spills may catch on re. Use a deep fat thermometer whenever possible to prevent fat overheating beyond the smoking point.

WARNING! Unattended cooking on a hob with fat or



oil can be dangerous and may result in re.

Never leave a chip pan unattended. Always heat fat



slowly, and watch as it heats. Deep fry pans should be only one third full of fat. Filling the pan too full of fat can cause spill over when food is added. If you use a combination of oils or fats in frying, stir them together before heating, or as the fats melt.

Foods for frying should be as dry as possible. Frost on frozen foods or moisture on fresh foods can cause hot fat to bubble up and over the sides of the pan. Carefully watch for spills or overheating of foods when frying at high or medium high temperatures. Never try to move a pan of hot fat, especially a deep fat fryer. Wait until the fat is cool.

Do not use the top of the ue (the slot along the back of the cooker) for warming plates, dishes, drying tea towels or softening butter.

Page 5

2. Cooker Overview

O O O

DocNo.020-0013 - Overview - 110DF - Classic, RM & Toledo lidded

Fig.2-1

ArtNo.212-0002 - 110 Classic ceramic front view

The 110 dual fuel cooker (Fig.2-1) has the following features:

A. 5 hotplate burners including a warmer and wok burner B. A control panel C. A grill D. Main conventional oven E. Fan oven F. Storage drawer

Hotplate Burners

The drawing by each of the central knobs indicates which burner that knob controls.

Each burner has an Flame Supervision Device (FSD) that prevents the ow of gas if the ame goes out.

Fig.2-2

When the igniter button is pressed in, sparks will be made at every burner – this is normal. Do not attempt to disassemble or clean around any burner while another burner is on, otherwise an electric shock could result.

To light a burner, press the igniter button, and push in and turn the associated control knob to the high position as indicated by the large ame symbol (

), (Fig.2-2).



Page 6

ArtNo.311-0001 Right pans gas

Fig.2-3

Fig.2-4

Fig.2-6

Fig.2-5

ArtNo.311-0002 Pan with rim

Fig.2-7

The igniter should spark and light the gas. Keep holding the knob pressed in to let the gas through to the burner for about ten seconds.

If, when you let go of the control knob, the burner goes out, then the FSD has not been bypassed. Turn the control knob to the OFF position and wait for one minute before you try again, this time making sure to hold in the control knob for slightly longer.

Adjust the ame height to suit by turning the knob clockwise

(Fig.2-3).

If a burner ame goes out, turn o the control knob and leave it for one minute before relighting it.

Make sure that the ames are under the pans. Using a lid will help the contents boil more quickly (Fig.2-4).

Large pans should be spaced well apart.

Pans and kettles with concave bases or down-turned base rims should not be used (Fig.2-5).

Simmering aids, such as asbestos or mesh mats, are NOT recommended (Fig.2-6). They will reduce burner performance and could damage the pan supports.

You should also avoid using unstable and misshapen pans that may tilt easily, and pans with a very small base diameter, e.g. milk pans, single egg poachers (Fig.2-7).

Art No. 311-0003 Simmer aids

Fig.2-8

ArtNo.311-0005 Wok burner & pan support

ArtNo.311-0004 Tipping wok

The minimum recommended pan diameter is 120 mm. The maximum allowable pan base diameter is 250 mm.

DO NOT use cooking vessels on the hotplate that overlap the edges.

Wok Burner

The wok burner is designed to provide even heat over a large area. They are ideal for large pans and stir-frying (Fig.2-8).

For heating smaller pans, the aforementioned hotplate burners may be more ecient.

You should wipe the enamel top surface of the cooker around the hotplate burners as soon as possible after spills occur. Try to wipe them o while the enamel is still warm.

Note:

The use of aluminium pans may cause metallic marking of the pan supports. This does not aect the durability of the enamel and may be cleaned o with an appropriate metal cleaner.

Page 7

The Wok Cradle

The wok cradle is designed to t a 35 cm wok. If you use a dierent wok, make sure that it ts the cradle. Woks vary very widely in size and shape. It is important that the wok sits down on the pan support – however, if the wok is too small, the cradle will not support it properly (Fig.2-9).

The cradle should be used on the triple ring wok burner only. When you t the cradle, make sure that it is supported properly on a pan support and the wok is sitting level in the cradle (Fig.2-10).

The cradle will get very hot in use – allow plenty of time for it to cool before you pick it up.

The Griddle

The griddle ts the left-hand pan support, front to back (Fig.2-11). It is designed for cooking food on directly. DO NOT use pans of any kind on it. The griddle surface is non-stick and metal cooking utensils (e.g. spatulas) will damage the surface. Use heat resistant plastic or wooden utensils.

DO NOT put it crossways – it will not t properly and



will be unstable (Fig.2-12).

DO NOT put it on any other burner – it is not



designed to t in any of the other pan supports.

Fig.2-9

ArtNo.311-0006 Correct wok sizes

Fig.2-10

ArtNo.311-0007 Wok stand close-up

Fig.2-11

Position the griddle over the hotplate burners resting on the pan support. Check that it is securely located.

The griddle can be lightly brushed with cooking oil before use (Fig.2-13). Light the hotplate burners. Adjust the ame heights to suit.

Preheat the griddle for a maximum of 5 minutes before adding food. Leaving it longer may cause damage. Turn the control knobs towards the low position, marked with the small ame symbol, to reduce the burner ames.

Always leave space around the griddle for the gases



to escape.

NEVER t two griddles side by side (Fig.2-14).



After cooking, allow the griddle to cool before cleaning.

ArtNo.311-0009 Oil on griddle

Fig.2-12

Fig.2-13

Fig.2-14

ArtNo.311-0008 Griddle positioning

Page 8

Fig.2-15

Fig.2-16

Warmer

On the right of the hob is the warmer (Fig.2-15). Use the warmer for keeping food warm while the nal touches are put to a meal. Turn the control knob counter-clockwise to the ‘On’ position.

For best results, preheat a covered serving dish for 10 minutes before adding food to it.

Use only heat resistant dishes.

The Grill

CAUTION: This appliance is for cooking purposes



only. It must not be used for other purposes, for example room heating.

CAUTION: Accessible parts may be hot when the grill



is in use. Young children should be kept away.

Fig.2-17

Fig.2-18

ArtNo.330-0003 - Grill pan w handle pulled forwards

ArtNo.210-0001 Classic grill control

ArtNo.331-0002 Grill pan high/low position

Open the door and pull the grill pan forward using the handle (Fig.2-16).

The grill has two elements that allow either the whole area of the pan to be heated or just the right-hand half.

Adjust the heat to suit by turning the control knob. To heat the whole grill, turn the control knob clockwise (Fig.2-17).

To heat the right-hand half, turn the control knob counterclockwise. The neon indicator light by the grill control will come on.

For best results, slide the grill pan back into the grill chamber and preheat the appropriate part(s) of the grill for two minutes. The grill trivet can be removed and the food placed on it while you are waiting for the grill to preheat.

Once the grill has preheated, slide the grill pan out again. With the trivet back in place with the food on it, slide the grill pan back into the grill chamber. Make sure that it is pushed right in.

The grill trivet can be turned over to give two grilling positions (Fig.2-18).

Do not leave the grill on for more than a few moments, without the grill pan underneath it.

Never close the grill door when the grill is on.



Page 9

The Ovens

The clock must be set to the time of day before the ovens will work. See the following section on ‘The Clock’ for instructions on setting the time of day.

Fig.2-19

References to ‘left-hand’ and ‘right-hand’ ovens apply as viewed from the front of the appliance.

The left-hand oven is a conventional oven, while the righthand oven is a fan oven.

The Conventional Oven

A conventional oven has two heating elements – one visible in the top of the oven and the other under the oven base.

Note: Be careful to avoid touching the top element and element deector when placing or removing items from the oven.

The exposed top element may cook some foods too quickly, so we recommend that the food be positioned in the lower half of the oven to cook. The oven temperature may also need to be lowered.

Similar items being cooked will need to be swapped around for even cooking.

The Fan Oven

The right-hand oven is a fan oven that circulates hot air continuously, which means faster, more even cooking.

The recommended cooking temperatures for a fan oven are generally lower than a conventional oven.

ArtNo.210-0002 Classic oven 1

ArtNo.210-0003 - Classic oven indicator

Fig.2-20

Note: Please remember that all cookers vary so temperatures

in your new ovens may dier to those in your previous cooker.

Operating the Ovens

Turn the oven knob to the desired temperature (Fig.2-19).

The oven indicator light will glow until the oven has reached the temperature selected. It will then cycle on and o during cooking (Fig.2-20).

The Browning Element

The Browning Element is positioned in the top of the lefthand oven. It can be used at the end of a normal cooking period to give extra browning to au gratin dishes or give a crisper nish to meat.

After the normal cooking is nished turn the left-hand oven thermostat knob clockwise to the browning position, indicated by (

Only the Browning Element will operate when the thermostat is turned to this position. The top and base cooking elements will switch o automatically.

ArtNo.030-0003 Browning

element symbol

) on the fascia panel.

Page 10

ArtNo.302-0004 -

Minute minder setting 2

ArtNo.302-0005a -

6BC Stopping the oven 1a

ArtNo.302-0006 - 6BC setting the cook time

ArtNo.302-0005a -

6BC Stopping the oven 1a

Fig.2-21

The Clock

You can use the timer (Fig.2-21) to turn the ovens on and o. The clock must be set to the time of day before the ovens will work.

ArtNo.302-0002 - 6BC annotated

ABCD EF

A – Minute minder, B – ‘Cook’ time, C – ‘Stop’ time, D – Manual,

E & F – Time setting buttons

Fig.2-22

ArtNo.302-0001 - 6-button clock

Fig.2-23 Fig.2-24

ArtNo.302-0003 - 6BC minute minder setting 1

Setting the Time of Day

When the clock is rst connected the display ashes ( 0.00 ) and () alternately.

Press and hold both the [] and [] buttons down (Fig.2-22). Now press the [+] button (or the [–] button) until the correct time shows.

Do not forget that it is a 24-hour clock.

If you need to reset the cooker, turn o the power supply and wait for a couple of minutes and start again.

Minute Minder

Press and hold the [] button (Fig.2-23), and then press the [+] button until the length of time you want to cook for is shown (Fig.2-24).

You can check the time remaining by pressing []. When the beeper sounds cancel it by pressing [].

• The ‘cook period’, which is the length of time you want the oven to cook for.

• The ‘stop time’, which is the time of day you want the oven to stop cooking.

Fig.2-25 Fig.2-26

ArtNo.302-0005 -

6BC Stopping the oven 1

Fig.2-27 Fig.2-28

Fig.2-29 Fig.2-30

ArtNo.302-0005 -

6BC Stopping the oven 1

To Stop the Ovens Automatically

Press and hold the ‘stop time’ [] button (Fig.2-25) and then press the [+] button (or [–] button) until the required ‘stop time’ shows (Fig.2-26). AUTO will show in the display.

Once the ‘stop time’ is reached, the beeper sounds. To stop the beep turn the oven control knob to 0 rst and then press [] once; press [] again to return to manual cooking.

To Start and Stop the Ovens Automatically

Before you set the clock you must have two numbers clearly in mind – the ‘cook period’ and the ‘stop time’.

Note: You cannot set a start time directly – this is set automatically by setting the ‘cook period’ and the ‘stop time’.

Press and hold the [] button (Fig.2-27) and then press the [+] button (or [–] button) until the required ‘cook period’ shows (Fig.2-28).

Now press and hold the [] button (Fig.2-29) and then press the [+] button (or [–] button) until the required ‘stop time’ shows (Fig.2-30). Release the buttons.

AUTO will now show in the display.

Set the oven(s) to the required temperature. When cooking is nished the beeper will sound. Turn the oven knob(s) to the OFF position rst, and then press the [] button once to stop the beep; press it again to return to manual cooking.

If you are out, do not worry about the beeper going o, it stops after a while. When you return, turn the oven knob(s) to 0 rst, and then press [] twice to return to manual cooking.

Page 11

AUTO is Showing, You Want to Reset to Manual

ArtNo.302-0011 - 6BC Deactivating the key lock 1

Cooking

To return to manual cooking from any automatic setting, the ‘cook period’ must be cancelled. Press and hold the [] button and then press the [–] button until the display reads ( 0.00 ).

Press the [] button to return to manual cooking.

Key Lock

When the key lock is activated, the ovens are locked and will not come on.

To Activate the Key Lock

Make sure that the clock is in manual mode and cancel any active programs.

Hold the Minute Minder [] and Cook period [] buttons. When ‘On’ appears on the display (Fig.2-31) press the [+] button once. The key symbol [ ] and ‘OF’ will now show on the display (Fig.2-32). Release the buttons.

The ovens are now locked, as conrmed by the display showing the time of day alongside the key symbol (Fig.2-33).

To Turn O the Key Lock

Hold the Minute Minder [] and Cook period [] buttons. When ‘OF’ appears on the display (Fig.2-34) press the [+] button once. The key symbol [ ] will go out and ‘On’ will show on the display (Fig.2-35). Release the buttons.

Fig.2-31

ArtNo.302-0008 Activating the key lock 1

Fig.2-33

ArtNo.302-0010 Activating the key lock 3

Fig.2-32

ArtNo.302-0009 - Activating the key lock 2

Fig.2-34

Fig.2-35

ArtNo.302-0012 Deactivating the key lock 2

After a few seconds, the display reverts to showing the time of day.

The ovens can now be used normally.

Page 12

ArtNo.320-0013 Removing the shelf 3

ArtNo.320-0012 Removing the shelf 2

Fig.2-36

Front

Shelf guard

Accessories

Oven Shelves

The oven shelves (Fig.2-36) can be easily removed and retted.

Pull the shelf forward until the back of the shelf is stopped by the shelf stop bumps in the oven sides (Fig.2-37).

Lift up the front of the shelf so the back of the shelf will pass under the shelf stop and then pull the shelf forward

(Fig.2-38).

Fig.2-37 Fig.2-38

ArtNo.320-0011 Removing the shelf 1

Fig.2-39

Fig.2-40

To ret the shelf, line up the shelf with a groove in the oven side and push the shelf back until the ends hit the shelf stop. Lift up the front so the shelf ends clear the shelf stops, and then lower the front so that the shelf is level and push it fully back (Fig.2-39).

The Handyrack (Main Oven)

The Handyrack (Fig.2-40) ts to the left-hand oven door only. Food cooking on it is easy to attend to, because it is accessible when the door is open.

The maximum weight that can be held by the Handyrack is 5.5 kg (12 lb). It should only be used with the supplied roasting tin, which is designed to t the Handyrack. Any other vessel could be unstable.

It can be tted at two dierent heights. One of the oven shelves must be removed and the other positioned to suit.

When the Handyrack is used in its highest position, other dishes can be cooked on the bottom shelf position or base of the oven.

When the Handyrack is used in its lowest position, other dishes can be cooked on the second shelf position or base of the oven.

Fig.2-41

Fig.2-43

ArtNo.320-0015

Fitting the Handyack 1

ArtNo.320-0014 Handyrack on LH door

ArtNo.320-0016

Fitting the handyrack 2

ArtNo.320-0026

- Oven light

To t the Handyrack, locate one side of it on the door bracket (Fig.2-41).

Then spring the other side out to clip it onto the other bracket (Fig.2-42).

Fig.2-42

Main Oven Lights

Press the button to turn the lights on (Fig.2-43).

If an oven light fails, turn o the power supply before changing the bulb. See the ‘Troubleshooting’ section for details on how to change the bulb.

Storage

The bottom drawer is for storing oven trays and other cooking utensils. It can get very warm, so do not store anything in it that may melt or catch re.

The drawer can be removed completely by pulling it right out and up.

Page 13

3. Cooking Tips

Tips on Cooking with the Timer

If you want to cook more than one dish, choose dishes that require approximately the same cooking time. However, dishes can be ‘slowed down’ slightly by using small containers and covering them with aluminium foil, or ‘speeded up’ slightly by cooking smaller quantities or placing them in larger containers.

Very perishable foods such as pork or sh should be avoided if a long delay period is planned, especially in hot weather.

DO NOT place warm food in the oven to be timed.



DO NOT use a timed oven that is already warm.



DO NOT use the timed oven if the adjoining oven is



already warm.

Whole poultry must be thoroughly defrosted before being placed in the oven. Check that meat and poultry are fully cooked before serving.

Temperature (Gas Mark) Temperature (°C / °F)

1 140 / 275

2 150 / 300

3 160 / 325

4 175 / 350

5 190 / 375

6 205 / 400

7 220 / 425

8 230 / 450

Table 3-1 Temperature conversion table

General Oven Tips

The wire shelves should always be pushed rmly to the back of the oven.

Baking trays with food cooking on them should be placed level with the front edge of the oven’s wire shelves. Other containers should be placed centrally. Keep all trays and containers away from the back of the oven, as overbrowning of the food may occur.

For even browning, the maximum recommended size of a baking tray is 340 mm (13½”) by 340 mm (13½”).

When the oven is on, do not leave the door open for longer than necessary, otherwise the knobs may get very hot.

• Always leave a “finger’s width” between dishes on the same shelf. This allows the heat to circulate freely around them.

• To reduce fat splashing when you add vegetables to hot fat around a roast, dry them thoroughly or brush lightly with cooking oil.

• Where dishes may boil and spill over during cooking, place them on a baking tray.

• The ‘Cook & Clean’ oven liners (see ‘Cleaning Your Cooker’) work better when fat splashes are avoided.

Cover meat when cooking.

• Sufficient heat rises out of the oven while cooking to warm plates in the grill compartment.

• If you want to brown the base of a pastry dish, preheat the baking tray for 15 minutes before placing the dish in the centre of the tray.

Page 14

4. Cooking Table

Bread

220 (C)

210

DocNo.031-0004 - Cooking table - electric & fan single cavity

The oven control settings and cooking times given in the table below are intended to be used AS A GUIDE ONLY. Individual tastes may require the temperature to be altered to provide a preferred result.

Food is cooked at lower temperature in a fan oven than in a conventional oven. When using recipes, reduce the fan oven temperature by 10 °C and the cooking time by 5-10 minutes. The temperature in the fan oven does not vary with height in the oven so you can use any shelf.

Conventional Oven

Temperature °C &

Food

Meat

Beef (no bone)

Lamb

Pork

Poultry

Chicken

Turkey

Duck

Casserole

Yorkshire pudding

Fish

Fillet

Whole

Steak

Cake

Very rich fruit - Christmas,

wedding, etc.

Fruit 180 mm tin

Fruit 230 mm tin

Madeira 180 mm

Queen cakes

Scones

Victoria sandwich

180 mm tin

210 mm tin

Desserts

Shortcrust tarts

Fruit pies

Tartlets

Puff pastry

Meringues

Baked egg custard

Baked sponge pudding

Milk pudding

(Shelf Position)

160 (C)

200 (C)

160 (C)

200 (C)

160 (C)

200 (C)

160 (C)

200 (C)

160 (C)

200 (C)

160 (C)

200 (C)

140-150 (C)

220 (C)

190 (C/B)

140 (C/B)

150 (C/B)

160 (C/B)

190 (C/B)

220 (C/B)

180 (C/B)

200 (C/B)

230 (C/B)

100 (C/B)

160 (C/B)

190 (C/B)

140-150 (C/B)

Fan Oven

Temperature

°C

150

190

150

190

150

190

150

190

150

190

150

190

130-140

210

180

130

140

150

180

210

170

190

220

150

180

130-140

Approximate cooking time

ArtNo.050-0001 Gas cooking table

30-35 minutes per 500g +30-35 minutes.

20-25 minutes per 500g +20-25 minutes.

30-35 minutes per 500g +30-35 minutes.

25-30 minutes per 500g +25-30 minutes.

35-40 minutes per 500g +35-40 minutes.

25-30 minutes per 500g +25-30 minutes.

20-25 minutes per 500g +20-25 minutes.

15-20 minutes per 500g +15-20 minutes.

20 minutes per 500g +20 minutes.

15 minutes per 500g +15 minutes.

25-30 minutes per 500g.

20 minutes per 500g.

2-4 hours according to recipe.

Large tins 30-35 minutes; individual 10-20 minutes.

15-20 minutes.

15-20 minutes per 500g.

Steaks according to thickness.

45-50 minutes per 500g of mixture.

2-2½ hours.

Up to 3½ hours.

80-90 minutes.

15-25 minutes.

10-15 minutes.

20-30 minutes.

30-40 minutes.

20-30 minutes on a preheated tray.

35-45 minutes.

10-20 minutes according to size.

20-40 minutes according to size.

2-3 hours.

45-60 minutes.

40-45 minutes.

2 to 3 hours.

20-30 minutes.

Top

Centre

Base

Thoroughly thaw frozen joints before cooking. Meat may be roasted at 220°C (210°C for fan oven) and the cooking time adjusted accordingly. For stuffed and rolled meats, add approximately 10 minutes per 500g, or cook at 200°C (190°C) for 20 minutes then 160°C (150°C) for the remainder.

For stuffed poultry, you could cook at 200°C (190°C) for 20 minutes then 160°C (150°C) for remainder. Do not forget to include the weight of the stuffing. For fresh or frozen prepacked poultry, follow instructions on the pack. Thoroughly thaw frozen poultry before cooking.

Using the conventional oven: when two tier cooking leave at least one runner space between shelves. Position the baking tray with the front edge along the front of the oven shelf.

Up to three tiers can be cooked in a fan oven at the same time but make sure to leave at least one runner space between each shelf being cooked on.

Using the conventional oven: for even browning the maximum size of baking tray recommended is 340 mm x 340 mm. This ensures free heat circulation. If cooking a two tier load, the trays should be interchanged approximately halfway though the cooking time.

ArtNo.050-0007

Oven shelf positions

Oven Shelf Positions

Page 15

5. Cleaning Your Cooker

Isolate the electricity supply before carrying out any thorough cleaning. Allow the cooker to cool.

NEVER use paint solvents, washing soda, caustic



cleaners, biological powders, bleach, chlorine based bleach cleaners, coarse abrasives or salt.

DO NOT mix dierent cleaning products – they may



react together with hazardous results.

All parts of the cooker can be cleaned with hot soapy water – but take care that no surplus water seeps into the

appliance.

Remember to switch on the electricity supply and reset the clock before re-using the cooker.

Hotplate Burners

The burner heads and caps can be removed for cleaning. Make sure they are absolutely dry before replacing them.

The Single Ring Burners

When retting the burner head, make sure that the notch lines up with the electrode or hole in the base. Check that the burner head is level and that the cap is tted centrally on the burner head (Fig.5-1).

ArtNo.311-0032 Burner layout FSD

A – Cap, B – Head, C – Notch, D – Base , E – Electrode

Fig.5-1

Fig.5-2

The Wok Burner

When reassembling the wok burner (Fig.5-2), turn over the large base ring and nd the ‘D’ shaped area (Fig.5-3). Turn the head until the ‘D’ matches the one on the burner base. Flip the burner over once again and place it on the burner base.

To t the small inner burner, nd the larger electrode notch in the burner rim. Line this up with the white ignition electrode and place the inner burner on the large base ring (Fig.5-4).

Now t the two burner caps, making sure that they are seated properly.

Check the burner ports are not blocked. If a blockage occurs, remove stubborn particles using a piece of fuse wire.

The Wok Cradle

Recommended cleaning materials are hot soapy water, a moistened soap pad, cream cleaner or a nylon scourer.

The Griddle

Always clean the griddle after use. Allow it to cool completely before removing. Immerse the griddle plate in hot soapy water. Use a soft cloth or, for stubborn stains, a nylon washing up brush.

ArtNo.311-0033 Wok burner details FSD

A – Inner burner cap, B – Outer burner head, C – Inner burner head,

D – Outer burner head, E – Wok burner base

Fig.5-3

Fig.5-4

Note: If the griddle is washed in a dishwasher then some

dishwasher residue may appear on the back. This is normal and will not aect the performance of your griddle.

ArtNo.311-0016 Fitting the burner inner head

A – Electrode notch, B – Ignition electrode

Page 16

Fig.5-5

Fig.5-6

ArtNo.320-0002a Proplus oven door side screws

ArtNo.320-0008 Removing the oven lining

Grill

The grill pan and trivet should be washed in hot soapy water. Alternatively, the grill pan can be washed in a dishwasher.

After grilling meats or any foods that soil, leave to soak for a few minutes immediately after use. Stubborn particles may be removed from the trivet using a nylon brush.

Before you remove any of the grill parts for cleaning,



make sure that they are cool, or use oven gloves.

DO NOT use any abrasive substances.



Control Panel and Oven Doors

Avoid using any abrasive cleaners including cream cleaners. For best results, use a liquid detergent.

The same cleaner can be used on the doors, or alternatively, using a soft cloth wrung out in clean hot soapy water – but take care that no surplus water seeps into the appliance. After cleaning, polish with a dry cloth.

Glass Fronted Door Panels

The oven door front panels can be taken o so that the glass panels can be cleaned. Move the cooker forward to gain access to the sides (see the ‘Moving the Cooker’ section under ‘Installation’).

Open the oven door slightly and remove the front panel xing screws from the door sides, two each side (Fig.5-5).

Carefully lift o the outer door panel. The inside face of the glass panels can now be cleaned – take care not to disturb or wet the door insulation.

Note: If the door is triple glazed then the inner two panels are xed together and should not be separated.

After cleaning, carefully ret the outer door panel and replace the side xing screws.

DO NOT use harsh abrasive cleaners or sharp metal



scrapers to clean the oven door glass since they can scratch the surface, which may result in shattering of the glass.

Ovens

‘Cook & Clean’ Panels

The ovens have panels which have been coated with a special enamel that partly cleans itself. This does not stop all marks on the lining, but helps to reduce the amount of manual cleaning needed.

The ‘Cook & Clean’ panels work better above 200 °C. If you do most of your cooking below this temperature, occasionally remove the panels and wipe with a lint free cloth and hot soapy water. The panels should then be dried and replaced and the oven heated at 200 °C for about one hour. This will make sure the ‘Cook & Clean’ panels are working eectively.

DO NOT use steel wool, oven cleaning pads, or any



other materials that will scratch the surface.

Page 17

Removing the Main Oven Linings

Some of the lining panels can be removed for cleaning. You will need to remove the shelves before removing the panels.

Each side of the oven is xed with four xing screws. You do not have to remove the screws to remove the oven linings. Simply lift each side panel upwards and they will slide o the screws (Fig.5-6). Then pull them forwards.

Cleaning Table

Cleaners listed (Table 5-1) are available from supermarkets or electrical retailers as stated.

For enamelled surfaces use a cleaner that is approved for use on vitreous enamel.

Regular cleaning is recommended. For easier cleaning, wipe up any spillages immediately.

Once the linings are removed, the oven enamel interior can be cleaned.

Hotplate

Part Finish Recommended Cleaning Method

Hob top Enamel or stainless steel

Ceramic/induction hob Toughened glass Hot soapy water; cream cleaner/scourer if necessary.

Griddle plate (some models only)

Warming zone (some models only)

Non-stick surface

Toughened glass Hot soapy water, cream cleaner/scourer if necessary.

Hot soapy water, soft cloth. Any stubborn stains remove gently with a nylon scourer.

Allow to cool. Wash in hot soapy water. Do not use abrasive cleaners/scourers. Dishwasher.

Outside of Cooker

Part Finish Recommended Cleaning Method

Door, door surround and Storage drawer exterior

Sides and plinth Painted surface Hot soapy water, soft cloth.

Splashback/rear grille Enamel or stainless steel

Control panel

Control knobs/handles & trims

Enamel or paint

Stainless steel

Paint, enamel or stainless steel

Plastic/chrome, copper or lacquered brass

Brass Brass polish.

Hot soapy water, soft cloth. Any stubborn stains, remove gently with a liquid detergent.

E-cloth (electrical retailers) or microfibre all-purpose cloth (supermarket).

Hot soapy water, soft cloth. Cream cleaner, with care, if necessary.

Warm soapy water. Do not use abrasive cleaners on lettering.

Warm soapy water, soft cloth.

Oven door glass/glass lid Toughened glass Hot soapy water, cream cleaner/scourer if necessary.

Oven and Grill

Part Finish Recommended Cleaning Method

Sides, floor & roof of oven NOT ‘COOK & CLEAN’ OVEN PANELS

(see below)

‘Cook & Clean’ oven panels (some models only)

Oven shelves, Handyrack, grill trivet, Handygrill rack (some models only)

Grill pan/meat tin (some models only)

Enamel

Special enamel that partly cleans itself

Chrome

Enamel Hot soapy water. Soap filled pad. Dishwasher.

Any proprietary oven cleaner that is suitable for enamel. CAUTION: CORROSIVE/CAUSTIC OVEN CLEANERS: FOLLOW

MANUFACTURER’S INSTRUCTIONS. Do not allow contact with the oven elements.

This surface cleans itself at 200 °C and above, or the panels can be removed and washed with hot soapy water and a nylon brush.

An oven interior cleaner that is suitable for chrome. Soap filled pad. Dishwasher.

Table 5-1

Page 18

6. Troubleshooting

Hotplate ignition or hotplate burners faulty

Is the power on? Is the clock illuminated?

If not, there maybe something wrong with the power supply.

Are the sparker (ignition electrode) or burner slots blocked by debris?

Are the burner trim and caps correctly located? See the section on ‘Cleaning’.

Hotplate burners will not light

Make sure that the burner parts have been replaced correctly after wiping or removing for cleaning.

Check that there is not a problem with your gas supply. You can do this by making sure that other gas appliances you may have are working.

Do the burners spark when you push the button?

If not, verify that the power is on by checking that the clock is illuminated.

Steam is coming from the oven

When cooking foods with high water content (e.g. oven fries) there may be some steam visible at the rear grille.

Power failure

In the event of a failure in the electrical supply, remember to reset the clock to make sure that the timed oven continues to operate.

Food is cooking too slowly, too quickly, or burning

Cooking times may dier from your previous oven.

Check that you are using the recommended temperatures and shelf positions – see the oven cooking guide. The oven control settings and cooking times are intended to be used only as a guide.

Individual tastes may require the temperature to be altered either way, to get the results you want.

The oven is not cooking evenly

Do not use a baking tray with dimensions larger than those specied in the section on ‘General Oven Tips’.

If you are cooking a large item, be prepared to turn it round during cooking.

If two shelves are used, check that space has been left for the heat to circulate. When a baking tray is put into the oven, make sure that it is placed centrally on the shelf.

Take care when opening the oven door, as there may be a momentary pu of steam when the oven door is opened. Stand well back and allow any steam to disperse.

What cleaning materials are recommended for the cooker?

See the ‘Cleaning’ section for recommended cleaning materials.

Never use caustic or abrasive cleaners as these will



damage the surface.

An oven fan is noisy

The note of the oven fan may change as the oven heats up – this is perfectly normal.

The knobs get hot when I use the oven or the grill. Can I avoid this?

Yes, this is caused by heat rising from the oven or the grill, and heating them up. Do not leave the oven door open.

Make sure that the grill pan is pushed right back to the ‘back stop’ when grilling.

Check that the door seal is not damaged and that the door catch is adjusted so that the door is held rmly against the seal.

A dish of water when placed on the shelf should be the same depth all over. (For example, if it is deeper at the back, then the back of the cooker should be raised up or the front lowered.) If the cooker is not level arrange for your supplier to level it for you.

Oven not coming on

Is the power on? Is the clock illuminated? If not, there may be something wrong with the power supply.

Is the cooker supply on at the isolator switch?

Has the time of day been set? Is the key symbol [] showing in the display to signify

that the oven is locked? See the ‘Clock’ section of the instructions for more information on the key lock feature.

The timed oven is not coming on when automatic cooking

Has the oven knob been left in the OFF position by mistake?

Always grill with the grill compartment door open.

If there is an installation problem and I don’t get my original installer to come back to x it who pays?

You do. Service organizations will charge for their call outs if they are correcting work carried out by your original installer. It is in your interest to track down your original installer.

Is the oven locked (see above)?

Oven temperature getting hotter as the cooker gets older

If turning the temperature down using the oven control knob has not worked, or has only worked for a short time, then you may need a new thermostat. This should be tted by a service person.

Page 19

An oven light is not working

The bulb has probably burnt out. You can buy a replacement bulb (which is not covered under the warranty) from a good electrical shop. Ask for a 15 W – 230 V lamp, FOR OVENS. It must be a special bulb, heat resistant to 300 °C (Fig.6-1).

Turn o the power at the circuit breaker.

Before removing the existing bulb, turn o the power supply and make sure that the oven is cool. Open the oven door and remove the oven shelves.

Unscrew the bulb cover by turning counter-clockwise. It may be very sti (Fig.6-2).

Taking care to protect your ngers with a glove in case the bulb should shatter, unscrew the old bulb.

Screw in the new bulb; screw back the bulb cover. Turn on the circuit breaker and check that the bulb now lights.

The oven door is misaligned

The bottom hinge of either oven door can be adjusted to alter the angle of the door (Fig.6-3). Loosen the bottom hinge xing screws and use the notch and a at bladed screwdriver to move the position of the hinge to set the hinge position (Fig.6-4).

Fig.6-1

ArtNo.324-0005 Oven light bulb

Fig.6-2

ArtNo.324-0007 Unscrewing the bulb cover

Fig.6-3

Retighten the hinge screws.

Eect of hinge adjustment – exaggerated for clarity

Centre line of hinge pin

ArtNo.320-0007 Oven door hinge adjustment 2

Oven door omitted for clarity

Fig.6-4

Page 20

INSTALLATION

Check the appliance is electrically safe and gas sound when you have nished.

7. Installation

Service and Spares

Firstly, please complete the appliance details below and keep them safe for future reference – this information will enable us to accurately identify the particular appliance and help us to help you. Filling this in now will save time and inconvenience if you later have a problem with the appliance. It may also be of benet to keep your purchase receipt with this leaet. You may be required to produce the receipt to validate a warranty eld visit.

Retailer’s Name and Address Andi Appliance Pty Ltd.

1 Stamford Road, Oakleigh, VIC 3166

Tel: (03) 1300 650 020 Fax: (03) 9569 1450 Email: Service@andico.com.au

Name of Appliance

Appliance Serial Number*

Fuel Type Dual Fuel

Date of Purchase

Installer’s Name, Address and Telephone No.

Date of Installation

* This information is on the appliance data badge.

If You Have a Problem

In the unlikely event that you have a problem with your appliance, please refer to rest of this booklet, especially the problem solving section, rst to check that you are using the appliance correctly.

If you are still having diculty, contact you retailer.

Please Note

If your appliance is outside the 12-month warranty period, our service provider may charge for this visit.

If you request an engineer to visit and the fault is not the responsibility of the manufacture, our service provider reserves the right to make a charge.

Appointments not kept by you may be subject to a charge.

Out of Warranty

We recommend that our appliances are serviced regularly throughout their life to maintain the best performance and eciency. The frequency of service will depend on usage – for normal usage once a year should suce.

Service work should only be carried out by a suitably Authorised Person.

Spare Parts

To maintain optimum and safe performance, we recommend that only genuine spare parts are used. Do not use reconditioned or unauthorised controls. Contact your retailer.

Page 21

INSTALLATION

Check the appliance is electrically safe and gas sound when you have nished.

Dear Installer

Before you start your installation, please complete the details below, so that, if your customer has a problem relating to your installation, they will be able to contact you easily.

Installer’s Name

Installer’s Company

ArtNo.050-0011 - Installer information table

Installer’s Telephone Number

Appliance Serial Number

Provision of Ventilation

This appliance is not connected to a combustion products evacuation device. Particular attention shall be given to the relevant requirements regarding ventilation.

The room containing the cooker should have an adequate air supply.

Install the cooker in a location to allow the complete combustion of gas, proper ueing and to maintain ambient temperature of the immediate surroundings at safe limits, under normal condition.

Location of Cooker

The cooker may be installed in a kitchen/kitchen diner but NOT in a room containing a bath or shower.

Note: An appliance for use on LPG must not be installed in a room or internal space below ground level, e.g. in a basement.

Conversion

All models are supplied set for use on Natural gas. A conversion kit for Propane gas is included with the appliance. See the instructions that are supplied with the conversion kit.

You must be aware of the following safety requirements & regulations.

Before installation, make sure that the local



distribution conditions (nature of the gas and gas pressure) and the adjustment of the appliance are compatible.

The appliance must be installed in accordance with



the regulations in force and only in a well ventilated space.

Read the instructions before installing or using this



appliance.

The regulations and standards are as follows:

• AS 5601 – ‘Gas Installations’

In your own interest and that of safety, it is law that all gas appliances be installed by competent persons.

Failure to install the appliance correctly could



invalidate any warranty or liability claims and lead to prosecution.

The cooker must be installed in accordance with all local gas tting regulations, municipal building codes, electrical wiring regulations and any other relevant statutory regulations.

After converting the appliance, please attach the Gas Conversion sticker over the appropriate area of the data badge – this will identify the gas type for which the appliance is now set.

WARNING!



Where this appliance is installed in a marine craft, caravan or mobile home, it shall NOT be used as a space heater.

Page 22

INSTALLATION

Check the appliance is electrically safe and gas sound when you have nished.

You will need the following equipment to complete the cooker installation satisfactorily:

• Flexible gas hose.

• Gas pressure tester/manometer.

• Multimeter: For electrical checks.

You will also need the following tools:

Electric drill

2. Masonry drill bit (only required if tting the cooker on a

stone or concrete oor)

3. Wall plugs (only required if tting the cooker on a stone

or concrete oor)

4. Steel tape measure

5. Cross head screwdriver

6. Flat head screwdriver

7. 4 mm & 3 mm Allen keys

8. Spirit level

9. Pencil

10. Adjustable spanner

11. 13 mm spanner or socket wrench

12. Screws for tting the restraining chain and bracket

Checking the Parts:

3 pan supports Griddle plate

Wok cradle Grill pan & trivet

ArtNo.000-0009 Wok ring, cast

ArtNo.330-0001 - Grill pan

Flat shelves & drop shelves Roasting tin

ArtNo.324-0011 Flat & drop shelves

ArtNo.324-0004 Roasting tin

Handyrack Splashback

ArtNo.324-0003 Handyrack

Plinth Stability bracket

Restraining chain & hook

ArtNo.020-0021 - Restraining chain & hook

ArtNo.421-0002 - Splashback

Page 23

INSTALLATION

130 mm

ArtNo.110-0023 - 110 - cooker clearances (AUS)

Check the appliance is electrically safe and gas sound when you have nished.

Positioning the Cooker

The diagram (Fig.7-1) shows the minimum recommended distance from the cooker to nearby surfaces as given in AS5601.

1. Overhead – Measurement A

The minimum height of any surface above the cooker is 650 mm above the hotplate.

Cookerhoods and exhaust fans shall be installed in accordance with the manufacturer’s instructions. However, in no case shall the clearance between the highest part of the hob of the cooking appliance and a cookerhood be less than 650 mm or, for an overhead exhaust fan, 750 mm.

2. Side Clearances – Measurements B & C

Where B, measured from the periphery of the nearest burner to any vertical combustible surface, or vertical combustible surface covered with toughened glass or sheet metal, is less than 200 mm, the surface shall be protected to make sure that the combustible surface does not exceed 65 °C above ambient*. Even with the surface protected, the dimension B should not be less than 135 mm above hotplate level.

*The xing of 5 mm thick ceramic tiles to the surface, or attaching re resistant material to the surface and covering with sheet metal with a minimum thickness of 0.4 mm to a height C of not less than 150 mm above the hotplate, should satisfy this requirement.

Fig.7-1

Fig.7-2

3. Side Clearances – Measurement D & E

Where D, the distance from the periphery of the nearest burner to a horizontal combustible surface is less than 200 mm, then E shall be 10 mm or more, or the horizontal surface shall be above the trivet.

A clearance of 130 mm is required if the cooker is near a corner of the kitchen, to allow the oven doors to open. The actual opening of the doors is slightly less, but this allows for some protection of your hand as you open the door (Fig.7-2).

We recommend a gap of 1110 mm between units to allow for moving the cooker. Do not box the cooker in it must still be possible to move the cooker in and out for cleaning and servicing.

Page 24

INSTALLATION

Check the appliance is electrically safe and gas sound when you have nished.

Fig.7-3

Fig.7-4

Fig.7-5

Moving the Cooker

On no account try and move the cooker while it is



plugged into the electricity supply.

The cooker is very heavy, so take great care.



We recommend that two people manoeuvre the cooker. Make sure that the oor covering is rmly xed, or removed, to prevent it being disturbed when moving the cooker around.

To help you, there are two levelling rollers at the back, and two screw-down levelling feet at the front.

Remove the polystyrene base pack. From the front, tilt the cooker backwards and remove the front half of the polystyrene base (Fig.7-3). Repeat from the back and remove the rear half of the polystyrene base.

Lowering the Two Rear Rollers

To adjust the height of the rear of the cooker, rst t a 13 mm spanner or socket wrench onto the hexagonal adjusting nut (Fig.7-4). Rotate the nut – clockwise to raise – counterclockwise to lower.

Make 10 complete (360°) turns clockwise.

ArtNo.010-0004 Moving the cooker

Make sure you lower BOTH REAR ROLLERS.

Completing the Move

Unfold the rear edge of the cardboard base tray. Open the grill door and right-hand oven door so that you can get a good grip on the bottom of the fascia panel as you move the oven (Fig.7-5).

Carefully push the cooker backwards o the base tray. Remove the base tray.

Position the cooker close to its nal position, leaving just enough space to get behind it.

DO NOT use the door handles or control knobs to



manoeuvre the cooker.

Page 25

INSTALLATION

Check the appliance is electrically safe and gas sound when you have nished.

Fitting the Stability Bracket and Chain

A stability bracket and chain MUST be tted when



the cooker is connected to a exible gas supply.

Unless properly installed, the cooker could be tipped by leaning on the door. Injury might result from spilled hot liquids or from the cooker itself.

IMPORTANT: The cooker must be set to the correct height and levelled before the stability bracket is installed.

Fitting a Stability Bracket

When tting a stability bracket please refer to the instructions supplied with the bracket for further details on tting.

When tting a stability bracket (Fig.7-6 and Fig.7-7) adjust the bracket to give the smallest practicable clearance between the bracket and the engagement slot in the rear of the cooker.

Fit the bracket so that it engages as far as possible over the chassis of the cooker.

Fitting the Restraining Chain

The restraining chain MUST be tted.

The length of chain between the appliance and the wall xing should prevent strain on the gas and electricity connections, but still allow access to unhook the chain when the cooker is pull forward.

Measure the length of chain required. Use the clamp supplied to clamp onto the gas pipe (Fig.7-8). Fix the supplied hook securely to the wall.

Stability bracket

ArtNo.070-0014 - Stability bracket - Wall fitting

Outer stability

bracket

Wall

Restraining

chain

ArtNo.011-0007 - Restraining chain (AUS)

Fig.7-6

Cooker

3 mm min

Floor

Typical oor mounting

Fig.7-7

Cooker

3 mm min

Floor

Typical wall mounting

Fig.7-8

Page 26

INSTALLATION

Art No 215-0028 - Handrail fascia fixings

Check the appliance is electrically safe and gas sound when you have nished.

Fig.7-9

ArtNo.215-0026 - Handle gaskets fixed

Fig.7-10

ArtNo.210-0006 - Classic fitting the handles 2

Fig.7-11

Levelling

You are recommended to use a spirit level on a shelf in one of the ovens to check for level.

Place the cooker in its intended position taking care not to twist it within the gap between the kitchen units as damage may occur to the cooker or the units.

The front feet and rear rollers can be adjusted to level the cooker.

To adjust the height of the rear of the cooker use a 13 mm spanner or socket wrench to turn the adjusting nuts at the front bottom corners of the cooker.

To set the front, turn the feet bases to raise or lower.

Fitting the Handles and Handrail

(Classic only)

Remove the 4 mm Allen screws from the doors (Fig.7-9). Fit the door handles and secure using the 4 mm screws.

The handles should be above the xings.



Fit the plastic blanking plugs to the xing holes (Fig.7-10).

Remove the 4 mm Allen screws from the top corners of the fascia (Fig.7-11). Fit the handrail in position and secure using the 4 mm screws.

Page 27

INSTALLATION

ArtNo.110-0011 110 DF gas hose connections

600

100

350

250

Gas inlet

block

All dimensions in millimetres

Check the appliance is electrically safe and gas sound when you have nished.

Gas Connection

Must be in accordance with the relevant standards.

The gas supply needs to terminate with a down-facing threaded tting ½” connection. The inlet connector is located just below the hotplate level at the rear of the cooker.

Because the height of the cooker can be adjusted and each connection is dierent it is dicult to give precise dimensions. Ideally, the house supply connection should be in the shaded area (Fig.7-12).

Means of isolation must be provided at the supply point by either an approved quick-connect device or a Type 1 manual shut-o valve.

The hose should be tted so that both inlet and outlet connections are vertical so that the hose hangs downwards in a ‘U’ shape (Fig.7-12).

A exible connection is supplied with the cooker. If it is necessary to use another hose it must be to AS 1869 class B and be suitable for your gas type.

If in doubt contact your supplier. Screw connect the threaded end of the hose into the gas inlet.

After completing the gas connection, check the cooker is gas sound with a pressure test. When checking for gas leakes do not use washing up liquid – this can corrode. Use a product specically manufactured for leak detection.

Fig.7-12

Natural Gas

The adjustable spring loaded gas pressure regulator is present to give a nominal pressure of 1 kPa on Natural Gas. Connect to the Rp ½ inlet on the underside of the pressure regulator.

Propane

This cooker is supplied ready for use on natural gas. A conversion kit for Propane as is supplied with the cooker – see the ‘Conversion to Propane Gas’ section.

Pressure Testing

The pressure test point is accessible on the inlet pipe at the rear. Remove the test nipple screw and t a pressure gauge to the test point. Turn on and light two of the hotplate burners.

For Natural Gas cookers the pressure should be 1 kPa.

For Propane X cookers the pressure should be 2.54 kPa.

Page 28

INSTALLATION

ArtNo.132-0004 - Fixed wiring connection (AUS)

Mains terminal

Fixing bracket for

conduit connection

Conduit

Cable clamp

Strain relief

bracket

Check the appliance is electrically safe and gas sound when you have nished.

Fig.7-13

Fig.7-14

Fig.7-15

ArtNo.132-0001 - 1 phase 240Vac 50Hz

1-phase 230 VAC 50 Hz

ArtNo.132-0003 - Single-phase connections (AUS)

A N

Electrical Connection

This appliance must be installed by a qualied electrician to comply with the relevant regulations (AS/NZS 60335.2.6) and also the local electricity supply company requirements.

Make sure that the mains characteristics (voltage, nominal, power, etc.) match the ratings indicated on the cooker data plate.

Current Operated Earth Leakage Breakers

The combined use of your cooker and other domestic

appliances may casue nuisance tripping, so we

recommend that the cooker is proctected on an individual

RCD (Residual Current Device) or RCBO (Residual Current

Breaker with Overload)

IF IN DOUBT, PLEASE CONTACT A SUITABLY QUALIFIED

ELECTRICIAN.

The cooker is preset for a single-phase earthed electrical connection. It is essential to install a multi-pole circuit breaker that completely disconnects the appliance from the mains, with a minimum contact break distance of 3 mm.

WARNING: THIS APPLIANCE MUST BE EARTHED.



The appliance must be connected to an ecient earthing circuit. If the electricity network is not equipped with an earth connection, then it must be installed separately in compliance with local regulations.

Earthing is a safety measure required by law, and must be performed with particular care by a qualied technician, who must also check that the electricity supply characteristics are correct.

ArtNo.132-0002 - 3 phase 240/415Vac 50Hz

3-phase 240/415 VAC 50 Hz

Fig.7-16

3-phase 230 V 50 Hz

The total electrical load of the appliance is approximately

7.3 kW. The cable size used should be suitable for this load

and comply with all local requirements.

Access to the mains terminal is gained by removing the electrical terminal cover box on the back panel. Connect the mains cable to the correct terminals for your electrical supply type (Fig.7-13 and Fig.7-14). Check that the links are correctly tted and that the terminal screws are tight. Secure the mains cable using the cable clamp.

Fixed Wiring

For connection to xed wiring, i.e. exible conduit, remove the electrical terminal cover box on the back panel. Using the two screws, x the strain relief bracket in position.

Fix the conduit-to-conduit mounting bracket onto the strain relief bracket. Connect the mains cable to the correct terminals for your electrical supply type (Fig.7-15 and Fig.7-16). Check that the links are correctly tted and that the terminal screws are tight.

Replace the electric terminal cover box; make sure that the conduit is clear of the bottom ange.

Page 29

INSTALLATION

Check the appliance is electrically safe and gas sound when you have nished.

Final Checks

Hotplate Check

Check each burner in turn (refer to the ‘Hotplate Burners’ section at the front of the instructions).

Grill Check

Turn on the grill control and check that the grill heats up.

Oven Check

Set the clock as described earlier in the instructions, and then turn on the ovens. Check that the oven fan starts to turn and that the ovens start to heat up.

Note: The oven light bulb is not included in the guarantee.

Turn o the oven.

Fitting the Plinth

Loosen the 3 screws along the front bottom edge of the cooker. Hook the central keyhole over the central screw. Twist and t each end keyhole over their respective screws. Tighten the xing screws (Fig.7-17).

Customer Care

Installer: Please complete your details in this Guide, inform the user how to operate the cooker and hand oven the instructions.

Fig.7-17

ArtNo.350-0012 - Securing the plinth

Thank you.

Page 30

WARNING – SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON

Art No 215-0028 - Handrail fascia fixings

Disconnect from electricity and gas before servicing. Check appliance is safe when you have nished.

8. Conversion to LP Gas

Fig.8-1

ArtNo.311-0010 Injectors

A – Jet, B – Internal injector, C – External injector

Fig.8-2

Fig.8-3

ArtNo.0102-0001 - Unscrewing the control valve bypass screw

Conversion from Natural Gas (1.0 kPa) to LPG X Propane (2.75 kPa)

A suitably competent person must perform the



conversion. After conversion the installation must comply with the relevant regulations and also the local electricity supply company requirements. Read the instructions before converting this appliance.

Failure to convert the appliance correctly could



invalidate any warranty or liability claims and lead to prosecution.

When servicing or replacing gas-carrying



components disconnect from the gas supply before starting operation. Check the appliance is gas sound after completion.

DO NOT use reconditioned or unauthorised gas



controls.

Disconnect from the electricity and gas supply



before servicing.

Before electrical reconnection, check that the



appliance is electrically safe.

Injectors

Remove the burner caps and heads. Remove the old jets (Fig.8-1). Fit the new jets (see the ‘Technical Data’ section at the back of this book for the correct jets). Reassemble in the reverse order.

Tap Adjustment

Classic – Removing the Control Panel

Remove the handrail. Now remove the 2 cross-headed screws hidden behind the handrail end brackets (Fig.8-2).

Pull o all the control knobs and remove the xing screws underneath the control panel.

Lift the control panel and pull forwards, taking care not to damage or strain the wiring.

Toledo – Removing the Control Panel

Pull o all the control knobs and remove the xing screws underneath the control panel.

Slide the control panel to the right and then pull forwards, taking care not to damage or strain the wiring.

Replacing the Tap Bypass Screws

Unscrew the tap bypass screw (Fig.8-3) and, using a pair of long nosed pliers, remove. Fit the correct replacement screw (see the ‘Technical Data’ section for details) and tighten down.

Ret the control panel.

Page 31

WARNING – SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON

ArtNo.103-0006 - Maxitrol cap & converter

Nut

Snap-in converter device

Disconnect from electricity and gas before servicing. Check appliance is safe when you have nished.

Set the Governor

Unscrew the governor’s brass top. In the base of the brass top is a plastic snap-in converter device (Fig.8-4). To convert the governor, snap the device out of the top and ret it the other way round. The snap-in converter device is marked to show the gas for which it is set (Fig.8-5).

Make sure the device is secure in the top cap and ret the cap to the governor.

Affix Label

Stick the appropriate gas label over the natural gas part of the appliance data label.

Pressure Testing

The pressure test point is accessible on the inlet pipe at the rear. Remove the test nipple screw and t a pressure gauge to the test point. Turn on and light two of the hotplate burners.

For Propane X cookers the pressure should be 2.54 kPa.

Check the appliance is gas sound.



Check operation of all the burners.



Fig.8-4

Fig.8-5

ArtNo.102-0007 - Maxitrol converter device positions

Page 32

WARNING – SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON

Art No 215-0028 - Handrail fascia fixings

Disconnect from electricity before servicing. Check appliance is safe when you have nished.

9. Servicing

Fig.9-1

Fig.9-2

BEFORE SERVICING ANY GAS CARRYING



COMPONENTS TURN OFF THE GAS SUPPLY

Check the appliance is gas sound after completion



of service. When checking for gas leaks DO NOT use washing up liquid – this can corrode. Use a product specically manufactured for leak detection.

DO NOT use reconditioned or unauthorised gas



controls.

Disconnect from the electricity supply before



servicing, particularly before removing any of the following: control panel, side panels, hotplate tray or any electrical components or covers.

Before electrical reconnection, check that the



appliance is electrically safe.

A – Flue grill, B – Cooker backsheet, C – Earthing/xing screws

Fig.9-3

A – Flue grill, B – Cooker backsheet, C – Earthing/xing screws

1 Panels

1.1 To Remove the Control Panel

DISCONNECT FROM THE ELECTRICITY SUPPLY.

Classic – Removing the Control Panel

Remove the handrail. Now remove the 2 cross-headed screws hidden behind the handrail end brackets (Fig.9-1).

Pull o all the control knobs and remove the xing screws underneath the control panel.

Lift the control panel and pull forwards, taking care not to damage or strain the wiring.

Toledo – Removing the Control Panel

Pull o all the control knobs and remove the xing screws underneath the control panel.

Slide the control panel to the right and then pull forwards, taking care not to damage or strain the wiring.

1.2 To Remove the Side Panels

DISCONNECT FROM THE ELECTRICITY SUPPLY.

Remove the control panel (see 1). Pull the cooker forward. Remove the 4 retaining screws for each panel (1 at the front base, 1 on the top and 2 at the rear).

Reassemble in the reverse order.

2 Hotplate

BEFORE SERVICING ANY GAS CARRYING



COMPONENTS, TURN OFF THE GAS SUPPLY.

2.1 To Remove the Hotplate

Pull the cooker forward to gain access to the rear.

Left-hand tray

From the rear remove the screws securing the ue grill to the hotplate tray. Remove pan supports, burner heads and caps. Remove the 4 screws and washers holding the hotplate tray to the frame. Raise the front of the hotplate then withdraw.

Page 33

WARNING – SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON

Disconnect from electricity before servicing. Check appliance is safe when you have nished.

Right-hand tray

From the rear remove the screws securing the ue grill to the hotplate tray. If the left-hand hotplate has not been removed, slacken the screws holding the left-hand tray. Remove pan support, burner head, caps and trim rings. Remove the screws holding the wok burner to the hotplate. Remove the two screws and washers holding the right-hand tray to the frame.

Press the wok burner down slightly and, taking care not to damage the wok burner electrode, slide the tray about 30 mm to right to clear the locating brackets on the right-hand side. Lift tray slightly at the front and taking care not to stress the warmer/lead junction, disconnect the leads to the warmer neon and separate the leads at the piggybacks. Withdraw the hotplate.

Reassemble in the reverse order ensuring that the leads are reconnected. When replacing the right-hand hotplate take care not to damage the ignition electrode of the wok burner.

It is important that the rear xing screws are retted as they from part of the cooker earthing.

On some models there is a separate plate (Fig.9-2). On others it is a tag on the cooker backsheet (Fig.9-3).

It is important that the tag is on the outside and that both xing screws are tted.

Check for correct burner operation.

2.2 To Replace the Hotplate Control Taps

DISCONNECT FROM THE ELECTRICITY SUPPLY.

BEFORE SERVICING ANY GAS CARRYING



COMPONENTS, TURN OFF THE GAS SUPPLY.

Remove the control panel and hotplate (see 1.1 & 2.1). Unplug the FSD lead from the rear of the tap. Undo the compression tting at the rear of the tap and remove the xings that secure the tap to the gas rail. Disconnect the ignition switch wiring.

Remove the tap. Remove and discard the gasket seal. Fit the new gasket seal to the replacement tap. Reassemble in reverse order. Check that the appliance is gas sound. Verify the hotplate ignition.

2.3 To Change a Hotplate Burner Injector

Remove the burner cap and head. Remove the old injector.

Fit the new injector. Reassemble in the reverse order. Check the appliance is gas sound.

2.4 To Replace a Hotplate Burner Electrode

DISCONNECT FROM THE ELECTRICITY SUPPLY.

Lift o pan supports and remove the burner cap. Remove the screw holding the electrode. Pull the electrode vertically up suciently to grip the lead between thumb and forenger.

Pull o the electrode, but keep hold of the lead. Fit the new electrode to the lead. Fix the electrode in the burner with screw. Replace the burner cap.

Check the burner ignition. Replace the pan supports.

2.5 To Replace a Hotplate Burner

DISCONNECT FROM THE ELECTRICITY SUPPLY.

Remove the hotplate tray (see 2.1). The burners (except the right-hand wok burner) are mounted on support struts. For these burners, disconnect the burner feed pipes at the burner. Remove the screws at the front and rear holding the support struts. Lift the strut and burners clear. The burners are xed to the support struts with two screws. Remove the appropriate burner and t the new one.

Reassemble in the reverse order. Check that the burner operation is satisfactory.

Right-hand Wok Burner

Disconnect the burner feed pipes at the burner. Fit the new one and reassemble in reverse order. Check

that the burner operation is satisfactory.

2.6 To Change the Warmer Neon

DISCONNECT FROM THE ELECTRICITY SUPPLY.

Remove right-hand hotplate (see 2.1). Carefully turn the hotplate upside down on a suitable at surface. Remove the 2 screws holding neon bracket to Warmer frame. Fit the new neon and bracket assembly.

Reassemble in the reverse order and check for correct operation.

2.7 To Change the Warmer

DISCONNECT FROM THE ELECTRICITY SUPPLY.

Remove the right-hand hotplate (see 2.1). Fit the new right-hand hotplate and reassemble in the reverse order.

Check the burner and warmer operation is satisfactory.

3 Controls

3.1. To Replace the Ignition or Light Switch

DISCONNECT FROM THE ELECTRICITY SUPPLY.

Remove the control panel (see 1.1). Note: The old switch may be destroyed during removal.

Remove the old switch from its bezel by gripping the switch body behind the control panel and twisting sharply. Remove the switch bezel by folding back the locking wings and pushing forward.

To t the new bezel to the control panel: rst line up the raised key on its body with the cut-out in the control panel and push it in from the front.

Assemble the new switch to the bezel by lining up the key sections and pushing home. Fit the new button by pushing in from the front.

Replace the control panel in the reverse order and test for correct operation.

Page 34

WARNING – SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON

Disconnect from electricity before servicing. Check appliance is safe when you have nished.

Fig.9-4

3.2 To Replace the Clock

DISCONNECT FROM THE ELECTRICITY SUPPLY.

Remove the control panel (see 1.1). Pull o the timer control buttons.

Undo the timer xing screws and remove the timer/ mounting bracket assembly from the control panel.

Remove the timer from its mounting bracket by depressing the plastic lugs on the timer case, and at the same time pulling the unit forward.

Reassemble in the reverse order. When replacing the leads, refer to the wiring diagram. Check the operation of the timer.

3.3 To Change the Warmer Switch

DISCONNECT FROM THE ELECTRICITY SUPPLY.

Remove the right-hand hotplate tray (see 2.1). Disconnect the wiring from the warmer switch. Remove the 2 screws holding switch to mounting panel, taking care not to lose the switch rotation limiter (Fig.9-4). Fit the new switch and reassemble in the reverse order. Check for correct operation.

3.4 To Change the Ignition Generator

DISCONNECT FROM THE ELECTRICITY SUPPLY.

Pull the cooker forwards to gain access to the cover box at the rear of the cooker. Remove the screws securing the cover and lift clear. Pull o all the leads to the generator noting their positions. Slacken the two screws holding generator to cooker and remove the generator.

Fit the new generator to the cooker and replace the leads. Refer to the wiring diagram and reassemble in reverse order. Check ignition performance.

4 Grill

4.1 To Replace the Grill Controller

DISCONNECT FROM THE ELECTRICITY SUPPLY.

Remove the control panel and hotplate (see 1.1 & 2.1). Disconnect the wiring from controller. Remove the two screws holding the controller to the mounting panel.

Fit the new controller and reassemble in the reverse order. Check for correct operation.

4.2 To Replace the Grill Element

DISCONNECT FROM THE ELECTRICITY SUPPLY.

Remove the grill pan from the grill chamber. From inside the grill compartment, undo the 2 screws and washers and remove the enamelled front shield from the grill roof. Remove two screws and washers securing the grill element front support. Remove the screws from the grill elements.

Carefully lift the elements out and disconnect the leads from the element terminals, noting their position.

If it is not possible to disconnect the leads in this way, pull cooker forwards to gain access to the rear.

Page 35

WARNING – SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON

Disconnect from electricity before servicing. Check appliance is safe when you have nished.

Remove the screws securing the electric cover to the back sheet, and then remove cover and disconnect the terminals from the rear.

Fit the new elements and reassemble in the reverse order. Check the operation of the grill.

5 Ovens

5.1 To Replace a Thermostat

DISCONNECT FROM THE ELECTRICITY SUPPLY.

Remove the control panel and hotplate (see 1.1 & 2.1). Open the oven door and remove the oven furniture.

For the right-hand oven, remove the thermostat phial cover (two screws). Unclip the thermostat phial from the clips in the oven back. For the left-hand oven, pull cooker forward to gain access to the cover box at the rear of the cooker. Remove the four screws securing the cover and lift clear.

Feed the thermostat capillary out of the oven. Disconnect the wiring from the thermostat. Remove two screws holding thermostat to mounting panel. Fit new thermostat and reassemble in the reverse order. Make sure that the phial is clipped to the oven back with the phial centrally positioned between the clips.

Check the operation of the thermostat.

Fig.9-5

ArtNo.320-0020 Oven back fixing screws

5.2 To Remove the Right-hand Oven Inner Back

Open the right-hand oven door. Remove the screws and washers securing the inner back to the back of the oven (Fig.9-5).

Carefully lift away the inner back. Reassemble in reverse order, making sure that you fully

tighten the 4 screws and washers.

5.3 To Change the Fan in the Right-hand Oven

DISCONNECT FROM THE ELECTRICITY SUPPLY.

Pull the cooker forward to gain access to the rear. Remove the screws securing the electric cover to the back sheet and remove the cover. Disconnect the three terminals connected to the fan, noting their position.

Remove the oven inner back (see 5.2). Hold the fan blade and remove the centre nut (left-hand thread), two brass washers, fan blade and circlip. Unscrew the fan retaining nuts and washers (three o each) and lift the fan away from the rear of the cooker.

Fit the new fan and reassemble in the reverse order. Check the operation of the oven.

5.4 To Remove an Oven Element Thermal Cut-out

DISCONNECT FROM THE ELECTRICITY SUPPLY.

Pull the cooker forwards to gain access to the cover box. Undo the cover screws and lift clear. The cut-out is located on the earth plate beside the oven element connections. Disconnect the cut-out wiring. Undo the xings that secure the cut-out to the earth plate and remove.

Page 36

WARNING – SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON

ArtNo.320-0001 Door hinges

ArtNo.321-0007 - MF oven element 1

ArtNo.321-0008 - MF oven element 2

Disconnect from electricity before servicing. Check appliance is safe when you have nished.

Fig.9-6

Element ﬁxing screws

ArtNo.321-0005 Fan oven element

Fig.9-7

Fig.9-8

Fig.9-9 Fig.9-10

Fit the replacement control and re-assemble in the reverse order.

5.5 To Remove the Right-hand Oven Element

DISCONNECT FROM THE ELECTRICITY SUPPLY.

Remove the oven inner back (see 5.2). Remove the two screws from the top of the element

and the one from the bottom of the element (Fig.9-6). Carefully lift the element out, disconnecting the terminals connected to the element (noting their positions). If it is not possible to disconnect the leads in this way, pull the cooker forward to gain access to the rear, remove the screws securing the electric cover to the back sheet, remove the cover and disconnect the terminals from the rear.

Fit the new element and reassemble in the reverse order. Check the operation of the oven.

5.6 To Remove the Left-hand Oven Bottom and Top Elements

DISCONNECT FROM THE ELECTRICITY SUPPLY.

Bottom Element

Pull the cooker forward to access the cover boxes at the rear of the unit. Remove the xings that secure the cover and lift it clear.

Remove the two screws ‘A’ and allow the plate to drop down (Fig.9-7). Remove the two screws ‘B’, lower the upper plate and remove through the slot in the cooker back (Fig.9-8).

Undo the terminal connections, noting their positions. Remove the element xings and withdraw the element.

Replace the element and re-assemble parts in reverse order.

Top Element

Open the left-hand oven door and undo the xings that secure the heat shield. Remove the top element bracket xings and withdraw element. Replace the element and re-assemble parts in the reverse order.

Check the oven operation.

6 Doors

6.1 To Remove the Grill Door

Remove the left-hand side panel – see 3. Remove the plinth (4 screws) and the central vertical cover (5 screws). Remove the two countersunk screws (1 each side) securing the grill hinge arms to the front of the grill chamber.

Note: The arms are spring tensioned. Carefully remove the grill door. Retain the gaskets.

Reassemble in reverse order, ensuring that the gasket is tted between the hinge arm and the front of the grill chamber.

Page 37

WARNING – SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON

ArtNo.320-0005 Oven door rubber seal

ArtNo.320-0003 Oven door latch

Disconnect from electricity before servicing. Check appliance is safe when you have nished.

6.2 To Replace an Oven Door

Open the oven door. Support the door and loosen the two screws securing the upper hinge and gasket to the cooker front (Fig.9-9).

The door is heavy, so take care.



Support the door and remove the screw nearest the hinge pin (Fig.9-10). Swing the hinge up and away from the door hinge pin. Lift the door away from the lower hinge and remove.

Reassemble in the reverse order.

6.3 To Adjust an Oven Door Angle

The bottom hinge of either oven door can be adjusted to alter the angle of the door (Fig.9-11). Loosen the bottom hinge xing screws and use the notch and a at bladed screwdriver to move the position of the hinge to set the hinge position (Fig.9-12).

Retighten the hinge screws.

6.4 To Replace an Oven Door Outer Panel

Move the cooker forwards to gain access to the sides. Open the oven door slightly and remove the 4 front

panel xing screws from the door sides (two each side), (Fig.9-13).

Carefully lift o the outer door panel. Remove the door handle from the panel by unscrewing

the two retaining nuts. Fit the door handle to the new panel. Fit the panel to the door. Reassemble in the reverse

order.

Centreline of hinge pin

ArtNo.320-0007 Oven door hinge adjustment 2

Oven door omitted for clarity

ArtNo.320-0006 Oven door hinge adjustment 1

Eect of hinge adjustment – exagerrated for clarity

Fig.9-11

Fig.9-12

Fig.9-13

6.5 To Change the Oven Door Latch

Remove the outer door panel (see 6.3). Remove screws ‘B’, which hold the latch assembly to the inner door panel (Fig.9-14). Fit the new catch and reassemble in reverse order. Check the door operation.

6.6 To Adjust an Oven Door Catch Keep

Open the oven door, slacken o the locknut at the base of the keep, and screw in or out as required until the required t is obtained. Retighten the locking nut

(Fig.9-15).

6.7 To Change an Oven Door Seal

Open the oven door. The seal is held in place by small hooks on the rear face. At the corner, pull the seal diagonally away from the door centre until that hook is released (Fig.9-16). Proceed to the next hook and release it in a similar way, and so on. Use force if the hooks are sti, as the old seal will be discarded.

When tting the new seal, position the seal join at the bottom. Hook the new seal in one of the corner holes of the door, and proceed round the door, snapping in each hook in turn.

Fig.9-14

ArtNo.320-0002a Proplus oven door side screws

Fig.9-15

ArtNo.320-0004 Oven door keep

Fig.9-16

Page 38

10. Circuit Diagram

brbr

w y

P093292

P095199

P025635

br w

br br brbr b b b

Key

The connections shown in the circuit diagram are for single-phase. The ratings are for 230 V 50 Hz.

Code Description

A1 Grill control

A2 Grill element left-hand side

A3 Grill element right-hand side

B1 Left-hand oven thermostat

B2 Left-hand oven control

B3 Left-hand oven base element

B4 Left-hand oven top element

B5 Left-hand oven browning element

C Clock

D1 Right-hand fan oven thermostat

D2 Right-hand fan oven switch

Code Description

F1 Warmer control

F2 Warmer

G1 Ignition switch

G2 Ignition spark generator

H1 Left-hand oven light switch

H2 Left-hand oven light

I1 Right-hand oven light switch

I2 Right-hand oven light

J Neon

K Thermal cut-out

Code Colour

b Blue

br Brown

bk Black

or Orange

r Red

v Violet

w White

y Yellow

g/y Green/yellow

gr Grey

D3 Right-hand fan oven element

D4 Right-hand fan oven fan

Page 39

11. Technical Data

This cooker is designed for use on natural gas but can be used converted to LP (Propane X (2.54 kPa)). A conversion kit from Natural Gas to Propane is supplied with the cooker.

INSTALLER: Please leave these instructions with the user.

DATA BADGE LOCATION: Cooker back, serial number repeater badge below oven door opening.

COUNTRY OF DESTINATION: Australia.

DocAUS.101-0024 - Technical data - DF 110 - Classic-Toledo

Connections

Gas (Rp ½ at rear right-hand side) Electric

Natural gas 1 kPa 230 V 50 Hz

Propane 2.54 kPa

See the appliance badge for test pressures.

Dimensions

Overall height minimum 900 mm maximum 925 mm

Overall width 1100 mm

Overall depth 600 mm to fascia; 650 mm over handles

Minimum space above the hotplate 650 mm

Refer to 'Positioning the Cooker'.

Ratings

Hotplate

Wok burner 15.2 MJh

Large burner 12.3 MJh 165 80 12.0 MJh 89 41

Medium burner 6.2 MJh 115 56 6.2 MJh 67 33

Small burner 3.7 MJh 92 48 13.3 MJh 48 25

Natural Gas 1 kPa LP Gas 2.54 kPa

Injector Bypass Injector Bypass

Internal 112

90 15.2 MJh

External 164 External 91

Internal 66

Oven Efficiency

Ovens

Maximum power output @ 230 V 50 Hz 2.2 kW 2.5 kW

Energy eciency class on a scale of A (more ecient) to G (less ecient) A A

Energy consumption based on standard load 0.99 kWh 0.90 kWh

Usable volume (litres) 67 69

Left-hand oven Right-hand oven

Conventional Forced air convection

Size Large Large

Time to cook standard load 40 minutes 38 minutes

Surface area of the grid 1400 cm

Grill 2.3 kW

Warmer 160 W

Maximum total electrical load at 230 V (approximate total including oven lights, oven fan, etc.): 7.3 kW.

1400 cm

Page 40

Clarence Street, Royal Leamington Spa,

Warwickshire, CV31 2AD, England.

Tel: +44 (0) 1926 457400 Fax: +44 (0) 1926 450526

E-mail: consumers@falconappliances.co.uk

Falcon CLAS110DFFBL-CH, CLAS110DFFCR-BR, CLAS110DFFCR-CH, CLAS110DFFCY-CH, CLAS110DFFBL-CHLPG Installation and Operation Guide

Specifications and Main Features

Frequently Asked Questions

User Manual