Factory Direct Hardware 6212 User Manual

Installation Instructions

®

931222-00

6212WF/6212WFDS Electric Strike

Single Door Wood Frame Mortise or Cylindrical Application

89/336/EEC

Notes: Deadbolt will not function with this strike.

1. For lock or device preparation, see their directions.

2. Prepare frame for strike (see other side).

3. Wire strike (Figure 1). (Switches on 6212WFDS only.)

Wiring
for DC

supply

Wiring
for AC

supply

Check with factory for retrofit applications.

SOLENOID POWER REQUIREMENTS

Yellow solenoid wires = 12 VDC, 0.57 A

Black solenoid wires = 24 VDC, 0.29 A

(also shown on strike label)

NOTE

!

DC input is

{

nonpolarized.

12 VAC SO-12 12 VDC
or
24 VAC SO-24 24 VDC

12 VDC

or

24 VDC

{

Use crimp

connectors to

splice field wiring

to P1 leads

P1 J1A P1A

P1

J1

SO-12 or SO-24

Figure 1

4. Test strike: Apply solenoid power. Fail secure (FSE) lip unlocks.
Fail safe (FS) lip locks. Figure 1 shows status of switches.

5. Install strike with two #12-24 screws. Make sure clearance
between latch bolt and strike lip is 1/32” (Figure 2). If not,
uninstall strike, adjust (Figure 3), and reinstall.

6. If latch bolt does not extend far enough to actuate tripper,

install extension (Figure 4). (Tripper on 6212WFDS only.)

7. Test door: With strike unlocked, door opens with latch bolt

extended. When door closes, latch bolt rides over strike lip.

P2

Solenoid

J2

S1

S2

Fail safe (FS)J2Fail secure (FSE)

depressed, strike lip closed and locked

(switches and tripper on 6212WFDS only)

1
2
3
4
5
6

J2

Switches shown with tripper

Use crimp connectors to
splice field wiring to P2
leads; insulate unused leads

S1

S2

1
2
3
4
5
6

Red (C)
Blue
Yellow
White (C)
Gray
Violet

P2

SWITCH RATINGS

Standard: 5 A, 30 VDC

Gold: 0.25 A, 30 VDC

}
}

S1

(monitors

tripper)

S2

(monitors

strike lip)

Strike lip

A

Latch bolt

1/32”

Top view;

faceplate not

shown for clarity

Figure 2

931222_00(6) Copyright © 2004 Ingersoll-Rand. All rights reserved.

Figure 3

B

Extension

Tripper

To adjust strike,
loosen screws A, B,
and C and move
backbox sideways
as necessary

Figure 4

C

C lock and strike

L

6-3/8”

5-5/8”

LHR shown

RHR opposite

Door Preparation for Strike

1” dia. minimum

clearance

2-3/8” minimum

clearance

C strike

L

1-1/4”

3/4”

3-3/8”

Pilot drill for

#12 wood screws

1-15/32”

5/8”

6-3/8”

3-3/16”

1-1/4”

2-3/8” minimum

1-7/16” minimum

clearance

5/8”

1-1/8”

2-13/16”

5-5/8”

clearance

C strike

L

6” long lead wires; 1/2” dia.

minimum wiring access

1-13/32”

1-11/16”

3-11/16”

3-3/8”

3-9/16”

931222_00(6)

1/8”

1-15/32”

Strike Dimensions and Required Clearances

Minimum

clearance