Factory Direct Hardware 6211WF User Manual

Installation Instructions

®

6211/6211DS Electric Strike

Single Door Mortise or Cylindrical Application

931227-00

89/336/EEC

Notes: Deadbolt will not function with this strike.

1. For lock or device preparation, see their directions.

2. Prepare frame for strike (see other side).

3. Wire strike (Figure 1). (Switches on 6211DS only.)

Wiring
for DC

supply

Wiring
for AC

supply

Check with factory for retrofit applications.

SOLENOID POWER REQUIREMENTS

Yellow solenoid wires: 12 VDC, 0.57 A

Black solenoid wires: 24 VDC, 0.29 A

(also shown on strike label)

NOTE

!

DC input is

{

nonpolarized

12 VAC SO-12 12 VDC
or
24 VAC SO-24 24 VDC

12 VDC

or

24 VDC

{

Use crimp

connectors to

splice field wiring

to P1 leads

P1 J1A P1A

P1

J1

Solenoid

SO-12 or SO-24

4. Install insert for auxiliary bolt operation (Figure 2).

5. Test strike: Apply solenoid power. Fail secure (FSE) lip unlocks.

Fail safe (FS) lip locks. Figure 1 shows status of switches.

6. Install strike with two #12-24 screws. Make sure clearance
between latch bolt and strike lip is 1/32” (Figure 3). If not,
uninstall strike, adjust (Figure 4), and reinstall.

7. If latch bolt does not extend far enough to actuate tripper,

install extension (Figure 5). (Tripper on 6211DS only.)

8. Test door: With strike unlocked, door opens with latch bolt

extended. When door closes, latch bolt rides over strike lip.

Use crimp connectors to
splice field wiring to P2
leads; insulate unused leads

S1

S2

1
2
3
4
5
6

P2

SWITCH RATINGS

Standard: 5 A, 30 VDC

Gold: 0.25 A, 30 VDC

Red (C)
Blue
Yellow
White (C)
Gray
Violet

(monitors

}

(monitors

}

strike lip)

Figure 1

J2 P2

S1

S2

Fail safe (FS)J2Fail secure (FSE)

depressed, strike lip closed and locked
(switches and tripper on 6211DS only)

1
2
3
4
5
6

J2

Switches hown with tripper

S1

tripper)

S2

Latch bolt

Fit hook on insert

into notch on

faceplate

Alternate insert

position

Figure 2

931227_00(8) Copyright © 2004 Ingersoll-Rand. All rights reserved.

Strike lip

1/32”

Top view;

faceplate not

shown for clarity

Figure 3

To adjust strike, loosen screws
A, B, and C and move backbox
sideways as necessary

For more
adjustment,
move screw A
to hole D

A

Figure 4

D

Extension

Tripper

B

C

Figure 5

4-7/8”

4-1/8”

3/8”

LHR shown

RHR opposite

C lock and strike

L

5/8”

Reinforce for

strike attachment

as required

1-1/4”

#16 drill and

#12-24 tap

2 places

1-15/32”

3/4”

3-3/8”

C strike

L

Suggested cutout

11/32” maximum

2” minimum

clearance

Strike

backbox

assembly

1-1/4”

4-7/8”

2-7/16”

Frame Preparation for Strike

1-21/32” minimum clearance

C lock and strike

L

5/8”

1-1/8”

2-1/16”

4-1/8”

C strike

L

3-3/8”

1-11/16”

931227_00(8)

1-1/4”

1/8”

Strike Dimensions and Required Clearances

12” minimum

clearance

6”