Page 1
These instructions should be read carefully prior to initial use and retained in
safe place in order that full advantage can be taken of the feature of your glass hob
Designer Hood
Instruction Manual
FABERJET TAZZA
220V～240V/50Hz
220W
≤2X2W
≥
(L) 896 511×(H)655×(W)
380Pa
≥
68dB
Technical Specifications
Model
Voltage
Motor Input
Light
Air Pressure (Max)
Noise
Outer Dimensions
Page 2
μ
List of Parts
Electric Circuit Diagram
Product Dimensions
Unit: mm
Please go through the list of parts to be assembled and ensure that all parts are accounted for
in good condition. Should there be any missing or damaged parts, kindly take the following actions:
No. Name Quantity
1
1
1
1
1
1
4 each
4
2
2
1
2
3
4
5
6
7
8
9
10
Range hood
Manual
Exhaust pipe
Oil catch
Mounting component
Securing bar for extended
chimney flue
Screws, flat washers
Switch
Circuit Board
Control
Wiring
Brown
Brown
White
Orange
Motor
Capacitance
Blue
Green-and-yellow
Light
Red
The parts or electric wires are subject to change without notice
Black
Black
Green
Plastic anchors
ST4.2x8 screws
M4x10 screws
Please keep it properly
1.5 m
To be installed on the range hood
To install the appliance
To secure the extended chimney flue
To install the appliance
To install the appliance
To secure the exhaust pipe
To secure the extended chimney flue
Note
Should our company or vendor be liable, please contact the vendor and request for them to
handle the issue.
Should the customer be personally liable, please contact the vendor or our company.
Page 3
Ceiling
Air Chamber
Outlet
2 keyholes
(10mm diameter)
4 keyholes
(10mm diameter)
(Keyholes to secure
the upper chimney flue)
(Keyholes to
secure the appliance)
≤102 0
≥906
≥950
650～7 50
332
520
169
48
637
Page 4
1.
2.
3.
1、
2、
3、
4、
5、
Using the Appliances
Maintaining the Appliances
Dismantling the Parts
Cleaning the Parts
Note: Please use a neutral cleansing agent
to clean the oil catch.
Operating the Appliances
Cleaning the oil catch
Cleaning the filter
Power Delay Timer Light
Please ensure that your appliance is well-maintained in order for it to function properly.
Please disconnect the appliance from the power supply before maintaining the appliance
by pulling out the plug head.
Please wear gloves when maintaining the appliance to avoid getting cut by the components
of the appliance.
To ensure the cleanliness and aesthetics of the appliance, the surface of the appliance
needs to be cleansed of grease frequently.
5、
A comprehensive maintenance procedure is to be performed once a year in order to
remove grease from all areas and ensure the optimum performance of the appliance.
Please empty out the oil from the catch
and clean it when it is about the be filled
to the brim.
You are advised to clean the filter every
three months. Use a screwdriver to remove
the filter and take it down. Then, soak the
Hold both sides of
the rectifier panel
and pull it downwards
to detach it from the
snaps. (Please avoid
pulling the panel down
forcefully as there
might be grease and
oil collected
on the rectifier panel)
Push the rectifier
panel backwards
until the hinges
of the panel are in
the middle before
removing the
rectifier panel.
Use a screwdriver to
remove the two screws
securing the filter before
taking it down to clean.
filter in warm water mixed with a neutral
cleansing agent for 30 minutes. After that,
use a brush to clean the filter gently.
To turn off the range hood: When the range hood is running, press the “power” button
to stop the appliance (this action does not affect the “light” function).
To turn on and turn off the light function: Press the “light” button to turn on the light and
press the “light” button again to turn it off.
To use the “delay timer” function: When the appliance is running, press the “delay timer”
button to extend the smoke and oil removal duration. Turn off the range hood when the
process is completed.
To turn on the smoke and oil removal function: Press the “power” button to turn on the
appliance before the “high speed” button to remove smoke and oil quickly or pressing
the “low speed” button to do so slowly.
Low Speed High Speed
Please exercise care when dismantling the parts in order to avoid deforming or damaging
the parts.
Lower
Chimney
Flue
Cover
Panel
Exhaust
Ring
Impeller
Remove the screws securing the lower chimney flue
(at the rear portion of the appliance) and take down the
chimney flue.
Remove the screws of the cover panel and take down
the cover panel.
Remove the screws securing the exhaust ring and take
down the exhaust ring.
Remove the impeller cap by turning it in the direction
indicated by the arrow shown on the cap and take down
the impeller.
When the maintenance procedure is completed,
reassemble the components in reverse sequence.
The parts should be cleaned with a neutral cleansing
agent and soft cloth or soft brush. Do not use organic
solvents.
It is best to rinse the parts after soaking them for 30
minutes. Please exercise care to avoid deforming or
damaging the parts.
Upon cleaning the parts, please rinse them with water
and dry them with a soft cloth.
Electrical parts are to be cleaned with a dry and
soft cloth or soft brush, and are not to be cleaned
with water or a cleansing agent.
Failure to follow the instructions in this manual might
result in the risk of the cooker hood catching fire.
Loading...