Faber 6074406-630006624, 607405-630006623, 6074456-630006627, 6074405-630006623, 6074457-630006628 User Manual
...
Agio
Integrated Collection
a stylish and space-saving alternative to the microwave hood
under cabinet tiltout rangehood
°
black or white glass front
°
optional stainless front kit
°
accepts drawer panels as front
°
closes flush with cabinets
°
easily replaces existing hoods
°
230 cfm
°
1 glass covered fluorescent light
°
3 speed control
°
dishwasher safe grease filters
°
convertible to ductless
°
top or direct rear venting
°
easy mounting system
°
sone range: 4.0 - 6.0
°
1/4” x 10” duct
3
°
For a seamless look in the kitchen, the Agio is your integrated solution.
With a black or white glass front that pairs well with ceran cooktops,
the Agio tilts in, flush with your cabinets, neatly tucking the hood away.
For total integration, the glass front can be replaced with material to
match your cabinets, hiding the hood completely.
Size/Color/Model #
24 White
24 Black
30 White
30 Black
36 White
36 Black
a
Stainless Front Kits
c
To replace the black or white glass
front with a stainless steel panel
c
24 Stainless
e
30 Stainless
s
36 Stainless
s
o
Charcoal Filters
r
For ductless installations, high
i
quality, heavy duty filters ensure the
removal of smoke and odors from
e
the kitchen.
s
6074405 / 630006623
6074455 / 630006626
6074406 / 630006624
6074456 / 630006627
6074407 / 630006625
6074457 / 630006628
6000024
6000030
6000036
6093032
To change the black or white glass front
to stainless steel, use our Stainless Front
Kits.
A patented front panel hinge system
allows the rangehood to tilt out when
in use and then tilt back in flush with
your cabinets to allow easy access to the
cabinets above. The direct rear venting
option frees up all the cabinet space
above.
The glass front can be replaced with a
standard drawer front or a custom piece
to integrate the Agio into the cabinetry.
p.o. box 435 • Wayland, MA 01778 • tel: (508) 358-5353 • fax: (508) 358-5730 • e-mail: info@faberonline.com • www.faberonline.com
Dimensional Diagram
Custom Front Panel Dimensions -
for replacing the entire front panel*
A
5 7/8”
B
C
* If you wish to keep the frame of the front panel and only replace the glass panel, the dimensions are as follows:
A=5 11/16”, B=1/8”, C= 23 6/16” (for 24” model) or 29 11/16” (for 30” model) or 35 11/16” (for 36” model). The glass panel is 1/8”
thick, but the frame is adjustable to accommodate a thinner panel like stainless steel.
Pre-Planning Your Installation - Important: Consult the installation instructions before you begin installing this
rangehood. The recommended height to install this hood off the cooktop is a minimum of 24” and a maximum of 30” for
maximum effectiveness. Also consult the cooktop manufacturer’s recommendation.
Pre-Planning Your Ductwork - Important:
Consult the installation instructions before you begin
installing this rangehood.
Make your ductrun as straight and short as possible.
The ductrun should not exceed 25 equivalent feet if
ducted with 3 1/4” by 10” rectangular duct. Count
45º angles as 3 feet, 90º elbows as 5 feet, and 90º flat
elbows as 12 feet.
For best results, use no more than three 90°
elbows. Make sure that there is a minimum of 24”
of straight duct between elbows if more than one
is used. Do not install two elbows together. If you
must elbow right away, do it as far away from the
hood’s exhaust opening as possible.
23 5/8” or 29 15/16” or 35 15/16”
Ductless Installations
For installations where ductwork
is impossible or highly impractical
Charcoal Filters, which attach to
the blower assembly, absorb smoke
and odors.
The blower must be positioned
with the exhaust pointing forward
(so that the exhaust exits from the
front grill).
13/16”
WARNING! Product specifications are subject to change without notification. Consult the installation instructions
before you begin installing this rangehood.
Rev.06/08
Loading...