Faber 6059890, 6059891, 6059892 Features & Dimensions
Pro Magnum
a professional performer
wall canopy rangehood
°
professional styling
°
3 chimney options
°
600 cfm for 30” & 36”
°
1200 cfm for 48”
°
3 halogen lights for 30” & 36”
°
4 halogen lights for 48”
°
3 speed control panel
°
stainless steel baffle filters
°
convertible to ductless with a kit*
°
top or direct rear venting
°
built-in mounting system
°
sone range: 4.5 - 7.0
°
3 1/4” x 10” duct for 30” & 36”
°
2 - 3 1/4” x 10” ducts for 48”
°
* it is highly recommended that
professional style cooking always be
vented to the outside.
Professional Collection
The Pro Magnum offers a good value
in the professional ventilation
category. Top or direct rear venting
and three chimney options make the
Pro Magnum the most versatile and
easy to install Pro hood on the market.
Size/Color/Model #
30 Stainless
36 Stainless
48 Stainless
a
Duct Transition Kit
For 48” model only, transitions two 3 1/4” x
c
10” openings to one 10” round opening
c
Galvanized Steel 6000002
e
Replacement Filters
For recirculating installations, high quality, heavy
s
duty filters ensure the removal of smoke and
odors from the kitchen. For 48” model, you
s
must order two of part #6093034, one kit for
o
each motor. There isn’t a ductless kit available
for 48” hood.
r
Ductless Vent Grate Kit
i
A 4” high stainless steel vent grate which
is installed below the cabinet to recirculate
e
the air back into the kitchen when
s
ducting outside is impossible or
impractical. Includes the stainless grate,
installation hardware and
p.o. box 435 • Wayland, MA 01778 • tel: (508) 358-5353 • fax: (508) 358-5730 • e-mail: info@faberonline.com • www.faberonline.com
6059890
6059891
6059892
6093034
Size / Model #
30” / DUCTGRT30
36” / DUCTGRT36
charcoal filters
Note: The Pro Magnum comes standard
WITHOUT A CHIMNEY. A telescopic
chimney kit or full width duct cover is
available separately.
Telescopic Chimney Cover
24” wide, extends to accomodate 8 - 9 foot
ceilings
24 Stainless
Full Width Duct Cover
12” high, extends full width of the hood
30 Stainless
36 Stainless
48 Stainless
6097336
6097337
6097338
6097339
25
"
25
"
Dimensional Diagrams
1/2”
3/8”
3
1/2”
1/4”
22
1/4”
23
1/2”
3/8”
4
Rectangular Hole which fits over the two 3 1/4” x 10”
exhaust openings on the rangehood
4”
3/8”
3
1/2”1/2”
14”
5/8”
2
3/4”
9
WITH TELESCOPIC CHIMNEY KIT WITH FULL WIDTH DUCT COVER
Pre-Planning Your Ductwork - Important: Consult the installation instructions before you begin installing this rangehood.
The Pro Magnum can be vented to the top or directly out the back.
Make your ductrun as straight and short as possible. The ductrun
should not exceed 35 equivalent feet if ducted with 3 1/4” by 10”
rectangular duct or 55 equivalent feet if ducted with 10” round
ductwork (when using Duct Transition Kit 6000002 for 48” model
only). Count 45º angles as 3 feet, 90º elbows as 5 feet, and 90º at
elbows as 12 feet.
Hole for Wiring Cable
30” AND 36” MODELS
For best results, use no more than three 90° elbows. Make sure
that there is a minimum of 24” of straight duct between elbows
if more than one is used. Do not install two elbows together. If
you must elbow right away, do it as far away from the hood’s
exhaust opening as possible.
48” MODEL
For 48” model, use two 3 1/4” by 10” rectangular duct runs or use the optional Duct Transition Kit shown here. This kit cannot be used
with the Telescopic Chimney Cover because it is too large to fit behind the cover. The Duct Transition Kit will fit behind the Full Width
Duct Cover.
WARNING! Product specifications are subject to change without notification. Consult the installation instructions before you begin installing this rangehood.
Hole for Wiring Cable
Hole for Wiring Cable
OPTIONAL DUCT TRANSITION KIT DIMENSIONS (48”MODEL ONLY)
Rev.01/11
Loading...