FAAC XKP W, XPK W 868, XKP W 433 Series Manual
XKP W
EN
1
!
+
CR2450 3 W
!
+
2
Ø 3.5 mm
XKP W 01 532110 - Rev.A
Ø max 6 mm
≥ 25 mm (A)
≥ 8 mm (B)
Ø max 3 mm
A
Guarnizione e Tappo di tenuta IP • IP
sealing gasket and cap • Joint et Bouchon
d'étanchéité IP • IP Dichtung und Verschlussstopfen • Junta y Tapa de estanqueidad IP • IP-Pakking en Afsluitdop
B
3
4
Guarnizione di tenuta IP • IP sealing gasket • Joint d’étanchéité
IP • IP Dichtung • Junta de
estanqueidad IP • IP dichtingspakking
XKP W 02 532110 - Rev.A
PH1
EN
Translation of the original instructions
CE DECLARATION OF CONFORMITY
The Manufacturer
Company name: FAAC S.p.A. Soc. Unipersonale
Address: Via Calari, 10 - 40069 Zola Predosa BOLOGNA - ITALY
hereby declares on his sole responsibility that the following products:
Description: SLH wireless keypad
Model: XKP W 433, XKP W 868
comply with the following applicable EU legislations:
2014/53/EU
2011/65/EU
Furthermore, the following harmonised standards have been applied:
EN 62368-1:2014
EN 62311:2008
ETSI EN 301 489-1 V2.2.0:2017
ETSI EN 301 489-3 V2.1.1:2017
ETSI EN 300 220-2 V3.1.1:2017
Bologna, 01-04-2018 CEO
Contents
1. XKP W ........................................ 2
Tec hnic al da ta ............................... 2
2. Installation ................................... 3
3. Programming ................................4
3.1 Store a user code ..........................5
3.2 Delete a user code .........................5
3.3 Delete all user codes ......................6
3.4 Change the PWD ..........................6
3.5 Restore factory settings ................... 6
3.6 Direct radio channel button E ...........6
3.9 Learn the radio code .................... 10
3.10 Set the XKP W Slave ................... 11
3.11 RandomisE the radio codes ........... 11
3.12 Easy or Advanced Operation .......... 11
Programming summary ...................12
4. Usage ....................................... 13
5. Troubleshooting............................ 14
6. Maintenance ............................... 14
Replace bat teries ...........................14
3.8 Teach the radio code ......................7
Teach a radio Recei ver .......................7
Teach another XKP W ........................ 8
Teach a Radio contr ol ........................9
XKP W 1 532110 - Rev.A
1. XKP W
The XKP W is included in the FAAC range of radio
control devices SLH. In order to operate correctly, all radio devices in a system must have the
same frequency, 868 MHz or 433 MHz (see the
FAAC catalogue) and in order to be recognised,
the channels of the devices must have the same
radio code as the receiver.
The XKP W allows the radio channels to be activated by entering the numeric codes reserved
for each user. Each user code must be stored on
the device using a programming procedure. In
order to restrict access, user codes must not be
given to other people.
The XKP W has 4 radio channels (Ch1, Ch2,
Ch3, Ch4).
A direct radio channel can be programmed that
is not code protected, which can be activated
using button E.
The XKP W cannot be used as an emergency
!
stop device.
The XKP W cannot be used as a hold-to-run
control.
The XKP W is factory set to Easy Operation
mode: each user code consists of 4 digits and
only ever activates one radio channel. Alternatively, Advanced operating mode can be
set: each user code has a variable length from
2 to 6 digits and can activate one, several or all
the radio channels that are available. The user
must always specify which radio channel he
wishes to activate.
XKP W master/ XKP W slave. The XKP W is factory
set to master, i.e. it can ‘teach’ its own radio codes
to another SLH radio device. The programming
function allows you to convert the XKP W into a
slave unit (i.e. it can ‘learn’ but not ‘teach’).
Programming which is password (PWD) protected allows you to:
- store user codes
- delete the user codes individually or all of them
- change the PWD
- restore factory settings
- enable/disable a direct radio channel using
XKP W 2 532110 - Rev.A
button E
- teach the radio codes to a SLH device or to learn
the radio codes from a SLH transmitter
- set the XKP W to a slave unit (this operation is
irreversible)
- randomise the radio codes
- set the mode of operation to Easy or Advanced
(possible only if the user code memory is empty)
Operation Easy Advanced
Code length 4 digits f rom 2 to 6
Activatable
channels
Direct radio
channel
TECHNICAL DATA
battery operated CR2450 3 W No. 2
average battery life
(10 activations/day)
radio frequency
XKP W 433
XKP W 868
type of coding SLH encrypted self-
MAX power consumption 20 mA
protection rating IP 54
operating temperature -20°C to +55°C
dimensions 100 x 72 x 21 mm
user code memory max 255 codes
only one Ch from 1 to 4 Ch
available available
digits
2 years
433.92 MHz
868.35 MHz
learning rolling code
Loading...