Complementary & Preliminary
O-line Barcode
voucher printer
Service and User Guide
2
Table of Contents
1. Technical characteristics 4
1.1 Power supply 4
1.2 Label creation for the Barcode voucher printer 5
1.3 The LED on the dispenser 5
2. Valiprint Configuration Tool 7
2.1 Connection 7
2.2 Parameter configuration 7
3. Use of the o-line Barcode voucher printer 9
4. Voucher: operation 11
4.1 Voucher: use 12
4.2 Voucher: already used or not valid 13
4.3 Voucher: cashing Agreements (parking lot operator) 14
3
▪ SERVICE: Hardware
▪ SERVICE: Hardware
4
▪ SERVICE: Hardware
1. Technical characteristics
Dimensions: 85.5mm (width) x 150mm (length) x 55mm (height)
Approximate weight: 400g (batteries and paper included)
Operating temperature (closed environments only): From 0°C to +50°C (From +32°F to +122°F)
Recharging temperature: From +10°C to +45°C (From +50°F to +113°F)
Storage temperature (non operative): From -20°C to +60°C (From -4°F to +140°F)
Relative humidity: 20 - 85%
Branches: Completely autonomous off-line operation
Internal supply: Rechargeable batteries 1.2V Ni-MH 1600mAH AA (4x)
External power supply and recharge device input: 100-230V AC +/- 10%, 50/60 Hz
Energy consumption:
-Standby - 30mA
-Average operation - 1.3A
Configuration interfaces: RS232 (COM on Pc). RJ12 (port on Validator)
Printing system: Directly on paper via thermal print head
Horizontal dot pitch: 0.125mm (approximately 200dpi)
Vertical dot pitch: 0.125mm
Printing width: 48mm
Paper width: 58mm
Paper roll diameter: 44mm
Paper roll length: 25m
Encryption information:
Validation information impressed via barcode by the built-in
thermal printer
Included Accessories
-4x rechargeable 1.2V Ni-MH 1600mAH AA batteries
-1 power supply unit with cord
Not Included Accessories
-Labels to be applied into the dispenser (see relevant chapter)
-Dispenser configuration software (supplied with the CD of the
Parkplus software and to be requested to the HUB Parking technical support service by email: 581@hubparking.com)
-Serial cable D9 <-> RJ12 for download from configuration
software
▪ Rechargeable Batteries:
Insert the rechargeable batteries checking the polarity.
Fig.1
N.B. Only use rechargeable batteries
as per specifications
Connect the power supply unit as shown in the picture
▪ Power supply unit:
Fig.2
1.1 Power supply
5
▪ SERVICE: Hardware
1 .....................................................
1 .....................................................
2 .....................................................
3 .....................................................
4 .....................................................
1
2
3
4
▪ 1 Button Dispenser Label
▪ 4 Button Dispenser Label
10% DISCOUNT
20% DISCOUNT
1 EURO REDUCTION
1h FREE PARKING
▪ Cut out and insert the label
▪ Fill in the label describing the function of each but-
ton (applied Agreement)
If there is an error, the LED flashes in sequence.
The reason can be identified by counting the number of flashes:
LED Indication Condition Solution
On On Off Off Short flashes every second Quick Recharge -
Out of Paper Replace Roll
Thermal head too hot Let it cool
Battery exhausted Recharge or replace batteries
Battery low (appr. 20% remaining) Recharge battery
Fig.3
Fig.4
Fig.5
Fig.6
1.2 Label creation for the Barcode voucher printer
1.3 The LED on the dispenser
▪ Size 52 mm x 23 mm
Loading...