FAAC SPX-5501 User Manual

SPX-5000 Series

Operations Manual

Suprex® Reader Extender - RF Wireless Interface

SPX-5521
900 Mhz

SPX-5601

2.4GHz

SPX-6601

2.4GHz

RPT-5651

2.4GHz
Repeater

IOX-7621

2.4GHz

EXP-2000

SPX-5000_MAN_082112

This manual covers the operation and setup of the Cypress Suprex RF SPX-5000 series wireless units.

Cypress Suprex SPX-5000 Series Overview

Physical

Weatherproof Enclosure - ABS - IP65
SPX units 6.75” x 4.75” x 2.10” (Each unit) - IOX units 7.25” x 5.75” x 3”

Temp

Storage(-55˚C to + 150˚C) - Operating(-40˚C to +80˚C)

Humidity

95% (non-condensing)

Power

Input

Unreg Input 8 to 16 VDC* @ 500mA Max
Unreg Input 8 to 24 VDC @ 500mA Max ( IOX-7000 )

Power

Output

+5VDC @100mA ( except IOX-7000 )

Data I/O

Interface

Reader -Wiegand, Strobed (Clock & Data), F/2F
LED - 0 - 30V

(220Vdc 30W (resistive) 1A)

Max Switching
(250Vac 37.5VA 1A)

Relays

(30Vdc 1A (resistive), 1 x 10

5

operations at 20o C

Relays

Running Spec with load
125Vac .3A (resistive), 1 x 10

5

operations at 20o C

Overview:

The SPX-5000 series of RF Wireless solutions provides a wireless bridge from Card Readers with gates or door
hardware to most access control manufacturers panels. The SPX or Suprex® products include both the remote
( Door/Gate ) unit and the central ( AC Panel ) unit. In the case of the SPX-5000 series of wireless products optional
repeaters / extenders are also available.

Features:

-- Includes complete solution with remote ( reader/gate/door ) and central ( panel ) interface.

-- Service mode for setup and configuration.

--“Quiet” protocol to conserve bandwidth and power

-- Field configurable reader formats

-- Multifunction indicator for determining operational status of the unit

-- Auxiliary I/O connections available for Door/Gate/Panel status signaling.

-- Multiplexing of RF bridge providing for additional door/gate on a single RF link.

-- Economical expansion capabilities using Suprex Lynk technology

RF Specifications:

2.4GHz or 900Mhz frequency
AES Encryption upon request

Electrical and Mechanical Specifications

Cypress Computer Systems, Inc. ⌖ Lapeer, MI 48446 ⌖ www.cypresscomputer.com

© 2012 Cypress Computer Systems Inc.

SPX-5521

915 Mhz - extender 10000 ft range

Wiegand or Clock & Data

816684003387

RPT-5551

915 Mhz - repeater 1000 ft range

N/A

816684003394

SPX-5601

2.4GHz - extender 2000 ft range

Wiegand or Clock & Data

816684003219

SPX-5621

2.4GHz - extender 10000 ft range

Wiegand or Clock & Data

816684003189

SPX-6601

2.4GHz - extender 2000 ft range

RS-232/RS-485

816684004599

RPT-5651

2.4GHz - repeater 1000 ft range

N/A

816684003172

IOX-7601

2.4GHz - extender 2000 ft range

N/A - Relays only

816684004551

810121416805535-40

Ambient Temperature

(Degrees Celsius)

Supply Voltage

Temperature/Voltage de-rating curve

Suprex® RF Part Numbers

Part Number! Description! ! ! ! Interface !! UPC

The Suprex units should be operated with a filtered 12 Volt nominal DC supply.
Any voltage between 8 and 16 volts can be utilized by following the temperature /voltage derating curve.
Voltage should not exceed 16 VDC under normal operating conditions.

Switch

6 7 8

0

1 x

2 x

3 x x

4 x

5 x x

6 x x

7 x x x

Wiegand

Wiegand / No Filter

Strobed Rising Edge (MR-5)

Strobed Rising Edge (Dorad0 644)

Strobed Rising (Mag-Tek)

Strobed Falling Edge

Reserved

F2F

x = ON

1234567

8

Dip switch #4 is ON

-Disable Pullup resistors

Dip switch #4 is OFF

-Enable Pullup resistors

Switch

6 7 8

0

1 x

2 x

3 x x

4 x

5 x x

6 x x

7 x x x

Wiegand

Wiegand / No Filter

Strobed Rising Edge (MR-5)

Strobed Rising Edge (Dorad0 644)

Strobed Rising (Mag-Tek)

Strobed Falling Edge

Reserved

F2F

x = ON

1234567

8

Dip switch #4 is ON

-Enable Pullup resistors

Dip switch #4 is OFF

-Disable Pullup resistors

1 - 8 to 16 VDC In
2 - Ground

Status LED

1 - exp (+)
2 - exp (-)
3 - +5 VDC out
4 - Prog Res 4
5 - Prog Res 3
6 - LED In
7 - D1/Data out
8 - D0/Clk out

1 - 8 to 16 VDC In
2 - Ground

Status LED

1 - exp (+)
2 - exp (-)
3 - +5 VDC out
4 - R4
5 - R3
6 - LED out
7 - D1/Data In
8 - D0/Clk In

External connections and DIP Switch Settings

SPX-5000

Central

SPX-5000

Remote

1- Relay 4 N.O.
2- Relay 4 Com
3 - Relay 4 N.C.
4 - Relay 3 N.O.
5 - Relay 3 Com
6 - Relay 3 N.C.
7 - Ground
8 - Aux out
9 - R2 in
10 - R1 in

1- Relay 2 N.O.
2- Relay 2 Com
3 - Relay 2 N.C.
4 - Relay 1 N.O.
5 - Relay 1 Com
6 - Relay 1 N.C.
7 - Ground
8 - Aux in
9 - Not used
10 - Not used

Central Unit Settings

DIP Switch #1 ON

-Service Mode
DIP Switch #1 OFF

-Run Mode

Remote Unit Settings

DIP Switch #1 ON

-Service Mode
DIP Switch #1 OFF

-Run Mode

DC

Ground

Ground

Power

Supply

Access
Control

Panel

Quick Reference For Typical Connections

SPX-5000 Series Central

+8 to +16 VDC

Diagnostic LED

LED In
D1/Data Out
D0/Clock Out

R1 Input
Controls
Strike on
Remote

R1 IN

DC

Power

Supply

Card

Reader

See page 10 for other strike control options

SPX-5000 Series Remote

+8 to +16 VDC

Diagnostic LED

R1 N.O.
R1 Com
R1 N.C.

LED Out
D1/Data In
D0/Clock In

Door

Strike

Output

Typical RF installation with repeater

ACS

ACS

SPX-5000R (1)

SPX-5000C (1) RPT-5X51

Typical RF installation - line of sight

SPX-5000C (1)

Typical RF installation ­expansion modules

ACS

SPX-5000C (1)

EXP-2000C (2)

SPX-5000R (1)

EXP-2000R (2)

EXP-2000R (3)

SPX-5000R (1)

Wiegand connection

Card reader

EXP-2000C (3)

RS-485 multi-drop

Control and I/O