FAAC SK-919TDWS-BU User Manual

Installation Manual

ENF ORCER

SK-919TDWS-B

Wired Single-Channel RF Transmitter

FEATURES:

• Powered by internal battery or external 12VDC

regulated adapter.

• Operates up to 500 feet.

• Frequency 315 MHz (433.92 MHz also available)

• Over 68 billion (6.8 x 10

• LED transmission indicator.

• Includes one 12VDC alkaline battery.

• Compatible with all SECO-LARM receivers.

• Compact size 2” x 1.5” x 0.59” (50 x 38 x 15mm)

• Wiring: Two, 6-inch blue wires for N.O. switch input.

Two, 6-inch wires (red & black) for 12VDC power input.

• SK-919TDWS-BU

) possible codes.

– same as SK-919TDWS-B, but no logo.

TYPICAL APPLICATIONS:

Make any push-to-exit plate wireless.

SK-910R RF Receiver

Compatible Receivers:

SK-910R – 1-Channel

SK-910R2 – 2-Channel

SK-910R4 – 4-Channel

Wireless equipment / perimeter security.

PIR

Wall

SK-910RA – 1-Channel

SK-910RAV – 1-Channel

SK-910RAV2 – 2-Channel

Electromagnetic Lock

Convert Dual-Beam sensors with dry contacts into entry alert system.

ENFORCER

SL-126A

Strobe

Wireless doorbell / Service call button.

Siren, chime, buzzer, etc.

INSTALLATION:

1) Power Connection – The wired transmitter can be

If an external power adapter is preferred, connect the red & black wires of the wired transmitter to the adapter’s output wires. Correct wire polarity must be observed. Red wire is for positive and black wire is for negative.

NOTE: a) The power input range of the wired

transmitter unit is 9~13.8VDC. Connecting more than 13.8VDC power or reversing the polarity will burn out the unit and void the warranty.

b) Use only 12VDC “regulated” adapters

to power the wired transmitter.

Example Connection Diagrams:

c) There is a factory-preinstalled 12VDC alkaline

battery inside the wired transmitter unit. If it is necessary to connect an external adapter, first remove the internal alkaline battery. Otherwise the internal battery will become defective and may overheat, leak, or explode.

2.) External Switch Connection – Aside from its own

built-in single button, the wired transmitter can also be controlled by an external N.O. pushbutton / sensor switch (not included), or use both the built-in & external switches (see Example Connection Diagram below). If an additional external N.O. switch is necessary, connect the two blue wires to the switch terminal.

NOTE: If the red & black or the two blue wire pairs are

not being used, the tips of the wires (where the copper is exposed) must be cut or wrapped to avoid a short circuit.

Battery Operated 12VDC Output

Adapter

Power on

Transmission

Push-Button or contact

Battery

12VDC Alkaline battery included

WARRANTY:

defects in material and workmanship while used in normal service for a period of one (1) year from the date of sale to the original customer. Our obligation is limited to the repair or replacement of any defective part if the unit is returned, transportation pre-paid, to SECO-LARM.

ENFORCER Wired Single-Channel RF Transmitters are warranted against

12VDC

Adapter

12VDC

adapter is optional

NOTICE

The information and specifications printed in this manual are current at the time of publication. However, the SECO-LARM policy is one of continual development and improvement. For this reason, SECO-LARM reserves the right to change specifications without notice. SECO-LARM is also not responsible for misprints or typographical errors.

SECO-LARMSECO-LARM

SECO-LARM

SECO-LARMSECO-LARM

16842 Millikan Avenue, Irvine, CA 92606

Tel: 800-662-0800 / 949-261-2999 Fax: 949-261-7326

U.S.A., Inc. U.S.A., Inc.

U.S.A., Inc.

U.S.A., Inc. U.S.A., Inc.

Website: www.seco-larm.com

E-mail: sales

seco-larm.com

Order Part # 762-103/934

MiSK-919TDWS-Bb.pmd

PITSW1