FAAC SD-6276-SS1Q User Manual

SD-6176-SSQ

Slimline plate, “TOUCH/EXIT”

SD-6176-SS1Q

Slimline plate, “EXIT/SALIDA”

SD-6176-SSVQ

Slimeline plate, manual override

SD-6276-SSQ

Single-gang plate, “TOUCH/EXIT”

SD-6276-SS1Q

Single-gang plate, “EXIT/SALIDA”

SD-6276-SSVQ

Single-gang plate, manual override

Piezoelectric push buttons for indoor

or outdoor use (IP65).

LED ring around button changes from

green to red or red to green when the
button is pressed.

Timed or toggle output.

Includes separate manual override

button in case power to piezoelectric
push button fails.

Relay rated 2A@30VDC with two

individually programmable outputs
(NO/NC).

Note: Products with model numbers that end with “Q” or that have a round green “Q” sticker are RoHS compliant.

Outdoor Piezoelectric

Request-to-Exit Pushbuttons

Manual

ENFORCER Outdoor Piezoelectric Request to Exit Pushbutton

Operating voltage

12~24 VDC

Current drain 100mA@12VDC

Contact rating

2A@30VDC or 0.5A@125VAC

Ring LED

Colors reversible v a switch

Standby

Red

Active

Green

Output time

1~30 s, Toggle

IP rating

IP65

Operating temperature

32 ~158 F (0 ~70 C)

Plate material

Stainless steel

Weight

Single-Gang

3.5-oz (99g)

Single-Gang w/Manual

Override

4-oz (113g)

Slimline

2.6-oz (74g)

Slimline w/Manual

Override

3.1-oz (88g)

Single-Gang

Slimline

41/2”

(114mm)

LED ring

Manual
override
button2

Piezo­electric
pushbutton

15/8” (42mm)

23/4” (70mm)

15/8” (42mm)

Side View

Rear View

(Plastic switch

cover removed)

Relay adjust

Output mode
selection

Terminal blocks

Manual override
button2

Buzzer adjust

LED color
selection

Timer adjustment

Terminal Block

Specifications:

Parts List:

Piezoelectric push button ........................... 1 x Mounting screws .................................. 2 x

Wires for manual override 1 ........................ 2 x Manual ................................................. 1 x

Overview:

SD-6176-SSVQ and SD-6276-SSVQ with Manual Override button shown, other models similar.

Installation:

1. Prepare wiring to provide 12~24 VDC power and connect devices to the relay outputs.

Note: The device includes one relay with two outputs. Outputs trigger simultaneously but can be
configured independently. To set the output modes, see Relay Output Modes on page 3.

2. Remove the plastic cover from the rear of the switch and carefully pierce the rubber grommet.

3. SD-6176-SSVQ and SD-6276-SSVQ: Wire the manual override button. See page 3.

4. Wire the switch according to the diagram on the right.

Connect (-) and (+) to a 12~24 VDC power source.
Connect other devices to Outputs 1 or 2.

5. Replace the plastic switch cover and screw the plate

onto the mounting surface.

1

SD-6176-SSVQ and SD-6276-SSVQ only.

2 SECO-LARM U.S.A., Inc

ENFORCER Outdoor Piezoelectric Request to Exit Pushbutton

Use the buzzer output jumper JP3 to program the buzzer output.
Placing the jumper on the left turns buzzer output ON. Placing the
jumper on the right turns buzzer output OFF.

Outputs 1 and 2 can be set independently using jumpers
JP1 and JP2. Note: Both outputs trigger simultaneously.
Place the jumper on the right for N.O. operation and on the
left for N.C. operation.

ON: LED is green while in standby, and turns red when triggered.
OFF: LED is red while in standby, and turns green when triggered.

TIMER: When set to TIMER, pressing the switch will trigger the relay for

the set time. Set the time using the trimpot as described above.
TOGGLE: When set to TOGGLE, pressing the switch will cause the
relay to trigger until the switch is pressed again.

Output duration is adjustable 1~30 seconds. (Must be set to ‘Timer’ in step 4)
Gently rotate the trimpot using a Philips head screwdriver.
Counterclockwise decreases the output time.
Clockwise increases the output time.

Wiring For N.O.:

Connect the two
wires between the
NO and COM
terminals of the
override button and
the Output 1 or 2
terminals on the
switch.

Wiring For N.C.:

Connect the two
wires between
the NC and COM
terminals of the
override button
and the Output 1
or 2 terminals on
the switch.

N.O.

COM

N.C.

COM

Manual

Override Button

Wiring the Manual Override: SD-6176-SSVQ and SD-6276-SSVQ Only

Connect the manual override button with the included wires.

Notes

a. Remove the thin panel on the bottom of the plastic cover to allow wiring to pass through.
b. There is only one relay, wiring the button to either output will allow the other output to trigger simultaneously.
c. Do not connect the manual override button to more than one output.
d. When wiring for either N.O. or N.C., be sure to also set the Relay Output Mode to N.O., as described below.

If Relay Output Mode and override button wiring do not match, the product may not function as expected.

Configuring the Pushbutton:

1. Buzzer Output DEFAULT: ON

2. Relay Output Mode DEFAULT: N.O.

3. LED Ring Colors DEFAULT: OFF

4. Switch Output Type DEFAULT: Timer

5. Timer Adjustment DEFAULT: 1s

SECO-LARM U.S.A., Inc 3

ENFORCER Outdoor Piezoelectric Request to Exit Pushbutton

Electromagnetic

Locks

Request-to-Exit

Plates

No-Touch

Request-to-Exit

RF Wireless

Request-to-Exit

MiSD-6x73-SSxQ_1111.docx

PIHWK1

ENFORCER
Electromagnetic Lock

ENFORCER

LED Strobe Light

Sample Installation: Electromagnetic Lock (Fail-Safe) with Strobe Light

Also Available from SECO-LARM:

WARRANTY This SECO-LARM product is warranted against defects in material and workmanship

while used in normal service for a period of one (1) year from the date of sale to the original consumer
customer. SECO-LARM’s obligation is limited to the repair or replacement of any defective part if the
unit is returned, transportation prepaid, to SECO-LARM. This Warranty is void if damage is caused by
or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair, or alteration,
improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines
that such equipment is not operating properly as a result of causes other than defects in material and
workmanship. The sole obligation of SECO-LARM, and the purchaser’s exclusive remedy, shall be
limited to replacement or repair only, at SECO-LARM’s option. In no event shall SECO-LARM be
liable for any special, collateral, incidental, or consequential personal or property damages of any kind
to the purchaser or anyone else.

NOTICE: The information and specifications printed in this manual are current at the time of
publication. However, the SECO-LARM policy is one of continual development and improvement. For
this reason, SECO-LARM reserves the right to change specifications without notice. SECO-LARM is
also not responsible for misprints or typographical errors.

Copyright © 2011 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced

or copied, in whole or in part, without the written permission of SECO-LARM.

SECO-LARM

16842 Millikan Avenue, Irvine, CA 92606 Website: www.seco-larm.com
Tel: [phone] Fax: [phone] E-mail: [e-mail]

4 SECO-LARM U.S.A., Inc

®

U.S.A., Inc.