FAAC PR-112S-A User Manual

Download

ENFORCER Stand-Alone Proximity Reader Manual ENFORCER Stand-Alone Proximity Reader Manual

Troubleshooting:

The LED does not light:

The relay does not activate

The relay time is too short

Egress button not working

• Check the power connection.

• Check the power supply.

• Make sure you are using a valid user card.

• Make sure the relay is not in toggle mode.

• Make sure you are using the correct relay output (either N.O. or N.C.).

• Set a longer door-release time.

• Make sure you are using a N.O. switch.

• Double-check the door-release time.

• Double-check the relay toggle mode.

ENFORCER

PR-112S-A

Stand-Alone Proximity Reader

Manual

WARNING: Incorrect mounting which leads to exposure to rain or moisture inside the enclosure could cause a dangerous electric shock, damage the device, and void the warranty. Do not open the case of this device, as there are no field-serviceable components inside.

WARRANTY

normal service for a period of one (1) year from the date of sale to the original consumer customer. SECO-LARM’s obligation is limited to the repair or replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM. This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair, or alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such equipment is not operating properly as a result of causes other than defects in material and workmanship. The sole obligation of SECO-LARM, and the purchaser’s exclusive remedy, shall be limited to replacement or repair only, at SECO-LARM’s option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or property damages of any kind to the purchaser or anyone else.

NOTICE: The information and specifications printed in this manual are current at the time of publication. However, the SECO-LARM policy is one of continual development and improvement. For this reason, SECO-LARM reserves the right to change specifications without notice. SECO-LARM is also not responsible for misprints or typographical errors. Copyright © 2013 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole or in part, without the written permission of SECO-LARM.

SECO-LARM U.S.A., Inc.

16842 Millikan Avenue, Irvine, CA 92606

Tel: 800-662-0800 / 949-261-2999 Fax: 949-261-7326

This SECO-LARM product is warranted against defects in material and workmanship while used in

Website: www.seco-larm.com E-mail: info

seco-larm.com

MiPR-1125-A_1302.pmd

●

Stand-alone operation

●

Sealed and weatherproof (IP67)

●

Tri-color LED status bar

SECOSECO

SECO

SECOSECO

Note: Products with model numbers that end with "Q" or that have a round green "Q" sticker are RoHS compliant

-LARM-LARM

-LARM

-LARM-LARM

●

Up to 100 user cards

●

Up to 5 master cards

●

Includes 10 blank cards

ENFORCER Stand-Alone Proximity Reader Manual ENFORCER Stand-Alone Proximity Reader Manual

Table of Contents:

Introduction .................................... 2

Specifications ................................. 2

Parts List ........................................ 2

Features ......................................... 3

Dimensions .................................... 3

Installation Instructions .................. 4

Wire Coding .................................. 4

Mounting Diagram ......................... 5

Getting Started ............................... 5

Programming................................ 6-8

Operating Instructions .................... 9

System Reset ................................ 10

User List ........................................ 11

Troubleshooting............................. 12

Introduction:

The ENFORCER PR-112S-A Stand-Alone Proximity Reader provides a flexible solution for securing controlled access. The stylish case and small size make it ideal for use in most residential, commercial, and industrial sites. The wave-shaped LED status bar accents the case design. Simple installation, quick programming, high reliability, and great looks are all combined in the PR-112S-A.

Specifications:

Power Input 12VDC Current Draw Standby: 80mA @ 12VDC

Max. Read Distance 6" (15cm) User Card Limit 100 cards Master Card Limit 5 cards Transmit Frequency 125Khz Outputs 1 relay (Com, N.O., N.C.) Contact Rating 1A @ 30V Relay Time Delay 1~180 secs. / Toggle mode Temperature -4 Enclosure Rating IP67 Dimensions 3

Active: 200mA @ 12VDC

~158oF (-20o~70oC)

/4" x 13/4" x 11/16"

(95 x 44 x 17 mm)

Parts List:

1 x PR-112S-A Proximity Reader 10 x Access Cards (PR-K1S1-A) 1 x Installation and Operation Manual

Also Available from SECO-LARM:

PR-K1K1-AQ

Proximity key fobs

(Sold in packs of 10)

PR-K1S1-A

Proximity cards

(Sold in packs of 10)

(Note: Use copy of chart - not original.)

User List:

User User Name Card #

_____________________________________________________________________________________

2 11

ENFORCER Stand-Alone Proximity Reader Manual ENFORCER Stand-Alone Proximity Reader Manual

System Reset:

Should it be necessary to completely reset the proximity reader, follow this procedure:

1. Disconnect power to the proximity reader.

2. Ground the BLUE wire:

2.1 If the egress button is connected, DO NOT open the case. Just press and hold the egress button.

2.2 If the egress button is not connected, you must unscrew the proximity reader from the wall, and ground the BLUE wire.

Cut

12VDC Power

power

BROWN: COM (input)

BLACK: Ground

BLUE: Egress Input

Egress

EXIT

SALIDA

3. While either pressing the egress button or grounding the BLUE wire, reconnect power. The LED will start to blink GREEN. Continue pressing the egress button or grounding the BLUE wire.

4. After about 3 seconds, the proximity reader should sound two long beeps. At this point, release the egress button or unground the BLUE wire.

NOTE: If a mistake is made, just restart this process from step 2 above.

5. After a few seconds, the proximity reader will sound 3 beeps and the LED will start flashing GREEN rapidly. After about 5 seconds, the LED will flash more slowly. At this point, tap any card to the proximity reader. This is now the first master card.

Beep Beep Beep

Flash Green! Green! Green!

...

5 sec.

Flash G..r..e..e..n! G..r..e..e..n! G..r..e..e..n!

. . .

(Blank Card)

Beep

Flash Blue!

Features:

●

Stand-Alone Proximity Card Reader.

●

Use in small businesses, homes, parking structures, apartments, and other locations.

●

Sealed and weatherproof (IP67). Mounts easily to interior and exterior walls.

●

Attractive tri-color wave-shaped LED status bar indicates proximity reader's mode and status.

Blue: On/Valid card indicator Green: Programming mode Red: Invalid card

●

Output relay for either timed (1 to 180 seconds) or "Toggle" mode.

●

Egress input to exit the protected area without using the proximity reader.

●

Buzzer is programmable for audible confirmation or silent mode.

●

Up to 100 user cards can be programmed.

●

User cards easily deleted. Delete a single card, or all cards.

●

Up to 5 "Master" cards can be programmed.

●

10 blank cards included.

Dimensions: (Actual size)

(16mm)

Front

side

33/4”

(95mm)

Back (Mounting Plate)

/16”

(40mm)

(21mm)

/8”

/16”

NOTE: After a system reset, all cards except the new master card are now considered to be blank cards.

13/4” (44mm)

/16” (17mm)

/16” (21mm)

(17mm)

/16” (21mm)

/16”

310

ENFORCER Stand-Alone Proximity Reader Manual ENFORCER Stand-Alone Proximity Reader Manual

Installation Instructions:

1. Unpack the unit and familiarize yourself with the proximity reader and the included parts.

2. Read this manual from front to back. There is a lot of good information here.

3. Test the mounting location for fit.

4. Using a T-10 Torx driver, remove the screw from the bottom of the proximity reader and

separate the outside case from the base.

5. Place the base on the mounting location, and then mark the two mounting holes and the wireharness hole.

6. Drill a 1/2" hole for the proximity reader's wire-harness.

7. Permanently screw the base into the mounting location.

8. Run the wires from the power supply, egress button, and door unlock device through the hole

to connect to the wire-harness.

9. Connect the wires to the proximity reader's wire-harness. Solder or crimp the connections, and carefully insulate them.

10. Reattach the outside case to the base.

11. The preliminary installation is done. Now program the proximity reader.

Wire Coding:

RED

(+) 12VDC

--(-

) GND

Egress Input

N.C. Output

N.O. Output

COM

EXIT

N.O. Egress switch

SALIDA

Relay, 1A@30VDC

Door lock device (i.e., magnetic lock)

12VDC Power

Sample Installation:

Key Notch for

Attaching Unit to Base

Screw Mounting Hole

Wiring Harness

Access Hole

Screw Mounting Hole

Nut for Base

Attachment Screw

Back

side

BLACK BLUE YELLOW GREEN BROWN

RED: 12VDC

YELLOW: N.C. (output)

GREEN: N.O. (output)

BROWN: COM (input)

BLACK: Ground

BLUE: Egress Input

Operating Instructions:

Entering the Premises – User Card

To enter a protected premise, tap the proximity reader one time with a user card. The LED turns off momentarily, the proximity reader sounds one short beep, and the relay output engages for the programmed time.

Exiting the Premises – Egress Button

To exit a protected premise, press the egress button once. The LED turns off momentarily, the proximity reader sounds one short beep, and the relay output engages for the programmed time.

Accidently Using an Invalid Card

If the proximity reader is tapped using a blank card, the LED flashes RED and the proximity reader sounds one long beep.

Beep

(User Card)

Beep

B..e..e..p!

Flash Red!

(Blank Card)

4 9

ENFORCER Stand-Alone Proximity Reader Manual ENFORCER Stand-Alone Proximity Reader Manual

___________________________________________________________________________________________________________________

Some examples:

___________________________________________________________________________________________________________________ Number of user cards Beep sequence

___________________________________________________________________________________________________________________

13 Long beep / 1 short beep / 3 short beeps

___________________________________________________________________________________________________________________

24 Long beep / 2 short beeps /4 short beeps

___________________________________________________________________________________________________________________

7 Long beep / Long beep / 7 short beeps

___________________________________________________________________________________________________________________

100 1 short beep / Long beep / Long beep

___________________________________________________________________________________________________________________ ___________________________________________________________________________________________________________________

8. Set the relay toggle mode: (timed output or toggle)

___________________________________________________________________________________________________________________

Action Reaction

___________________________________________________________________________________________________________________

Tap a master card 8 times 2 quick beeps, 7 more beeps

___________________________________________________________________________________________________________________

Wait 3 seconds 8 beeps, green flashes continue

___________________________________________________________________________________________________________________

Mounting Diagram:

plate to surface

Proximity

reader

Mounting plateScrew mounting

Wait a second, and the mode Beeps 1 time = normal mode changes automatically Beeps 2 times = latched mode

___________________________________________________________________________________________________________________

The unit automatically exits to standby mode

___________________________________________________________________________________________________________________

Normal mode -- Use a user card to unlock the door, the door automatically locks after

___________________________________________________________________________________________________________________

the timer expires.

___________________________________________________________________________________________

___________________________________________________________________________________________________________________________________________

Included

case screw

Toggle mode -- Use a user card to unlock the door, and then use a user card to relock the door.

9. Not used, reserved for future use:

10. Set the beeper mode: (to beep or not when a user card is used)

___________________________________________________________________________________________________________________

Action Reaction

___________________________________________________________________________________________________________________

Tap a master card 10 times 2 quick beeps, 9 more beeps

___________________________________________________________________________________________________________________

Wait 3 seconds 10 beeps, green flashes continue

___________________________________________________________________________________________________________________

Wait a second, and the mode Beeps 1 time = beeper off changes automatically Beeps 2 times = beeper on

___________________________________________________________________________________________________________________

The unit automatically exits to standby mode

___________________________________________________________________________________________________________________

NOTE

When the beeping is programmed off, the proximity reader will still beep during

the programming mode.

___________________________________________________________________________________________________________________

Getting Started:

Card Types:

There are three basic types of cards used by the proximity reader:

●

Master Card (MC) – Used for programming only. It does not give access to the protected premises.

●

User Card (UC) – Used for access only. Considered to be a valid card.

●

Blank Card (BC) – A card that has not yet been programmed into the proximity reader. Considered to be an invalid card.

NOTE – The proximity reader can learn up to 5 master cards and 100 user cards.

LED Color Meanings:

LED Color ............... What it means

Blue .........................The proximity reader is powered on and in the standby mode

Green ......................The proximity reader is in the programming mode

Red ......................... Indicates an error

First-Time Power Up:

1. After connecting power the unit should beep once and the LED should be Blue - Theproximity

reader is ready to be programmed using the included master card marked with a

2. If after connecting power for the first time the LED is flashing master card by tapping it to the reader.

3. This will be followed by 2 short beeps and the LED should turn

4. The proximity reader is ready to be programmed using the master card you just created.

Green you must program your

Blue.

Through hole

for cables

red sticker.

8 5

ENFORCER Stand-Alone Proximity Reader Manual ENFORCER Stand-Alone Proximity Reader Manual

Programming:

___________________________________________________________________________________________________________________

1. Add a new user card:

___________________________________________________________________________________________________________________

Action Reaction

___________________________________________________________________________________________________________________

Tap a master card 1 time 2 quick beeps, LED flashes green

___________________________________________________________________________________________________________________

Wait 3 seconds 1 beep, green flashes continue

___________________________________________________________________________________________________________________

Tap a blank card 1 time 1 beep, the card is now a user card

___________________________________________________________________________________________________________________

Tap more blank cards 1 time 1 beep for each new user card each to create more user cards

___________________________________________________________________________________________________________________

Exit -- To exit programming mode, tap a master card 1 time or wait 15 seconds.

_________________________________________________________________________________________________________________

NOTE

Attempting to add a previously-learned user card or master card will cause the

unit to beep twice and the LED to flash red.

2. Delete the user card following this user card:

___________________________________________________________________________________________________________________

Use this to delete a user card that was not returned by an employee

___________________________________________________________________________________________________________________

Action Reaction

___________________________________________________________________________________________________________________

Tap a master card 2 times 2 quick beeps, 1 more beep, LED flashes green

___________________________________________________________________________________________________________________

Wait 3 seconds 2 beeps, green flashes continue

___________________________________________________________________________________________________________________

Tap the user card that was added 2 quick beeps, the desired user card is deleted just before the card to be deleted

___________________________________________________________________________________________________________________

Exit - To exit programming mode, tap a master card 1 time or wait 15 seconds.

___________________________________________________________________________________________________________________

NOTE

Attempting to delete a blank card or a master card will cause the unit to beep

twice and the LED to flash red.

________________________________________________________________________________________ ___________________________________________________________________________________________________________________

3. Delete this user card:

___________________________________________________________________________________________________________________

Use this to delete a user card that is in your possession

___________________________________________________________________________________________________________________

Action Reaction

___________________________________________________________________________________________________________________

Tap a master card 3 times 2 quick beeps, 2 more beeps, LED flashes green

___________________________________________________________________________________________________________________

Wait 3 seconds 3 beeps, green flashes continue

___________________________________________________________________________________________________________________

Tap the user card to be deleted 3 quick beeps, the user card is deleted

___________________________________________________________________________________________________________________

Exit -- To exit programming mode, tap a master card 1 time or wait 15 seconds.

___________________________________________________________________________________________________________________

NOTE

Attempting to delete anything other than a user card will cause the unit to beep

twice and the LED to flash red.

4. Delete all user cards:

___________________________________________________________________________________________________________________

Action Reaction

___________________________________________________________________________________________________________________

Tap a master card 4 times 2 quick beeps, 3 more beeps, LED flashes green

___________________________________________________________________________________________________________________

Wait 3 seconds 4 beeps, green flashes continue

______________________________________________________

________________________________________________________________________________________________________________________________________________________________________________

______________________________________________________________________________________________________________________________________________

___________________________________________________________________________________________________________________

WITHIN 3 SECONDS, 4 quick beeps, all user cards are deleted tap the master card again

___________________________________________________________________________________________________________________

The unit automatically exits to standby mode

5. Add a new master card:

___________________________________________________________________________________________________________________

Action Reaction

___________________________________________________________________________________________________________________

Tap a master card 5 times 2 quick beeps, 4 more beeps, LED flashes green

___________________________________________________________________________________________________________________

Wait 3 seconds 5 beeps, green flashes continue

___________________________________________________________________________________________________________________

Tap a blank card or a user card 2 beeps, the card is now a master card

___________________________________________________________________________________________________________________

Tap more blank or user cards 1 time 2 beeps for each new master card each to create more master cards

___________________________________________________________________________________________________________________

Exit -- To exit programming mode, tap a master card 1 time or wait 15 seconds.

6. Set the door-release timer:

___________________________________________________________________________________________________________________

Action Reaction

___________________________________________________________________________________________________________________

Tap a master card 6 times 2 quick beeps, 5 more beeps, LED flashes green

___________________________________________________________________________________________________________________

Wait 3 seconds 6 beeps, green flashes continue

___________________

___________________________________________________________________________________________________________________________________________________________________________________________________________________

Count the beeps 1 beep = 1 second for the door release timer

___________________________________________________________________________________________________________________

Tap the master card to stop the beeps The timer is now set for the number of seconds equal to the number of beeps

___________________________________________________________________________________________________________________

The unit automatically exits to standby mode

7. Show me how many user cards have been programmed:

___________________________________________________________________________________________________________________

Action Reaction

___________________________________________________________________________________________________________________

Tap a master card 7 times 2 quick beeps, 6 more beeps

___________________________________________________________________________________________________________________

Wait 3 seconds 7 beeps, green flashes continue

___________________________________________________________________________________________________________________

Wait 1.5 seconds Silence

___________________________________________________________________________________________________________________

Count beeps for the first digit Long beep=0 or 1 beep=1

___________________________________________________________________________________________________________________

Wait 1 second Silence

___________________________________________________________________________________________________________________

Count beeps for the second digit Long beep=0 or 1-9 beeps

___________________________________________________________________________________________________________________

Wait 1 second Silence

___________________________________________________________________________________________________________________

Count beeps for the third digit Long beep=0 or 1-9 beeps

___________________________________________________________________________________________________________________

The unit automatically exits to standby mode

___________________________________________________________________________________________________________________

Counting the beeps digits together gives the number of user cards that have already been programmed. See the examples on page 8.

___________________________________________________________________________________________________________________

*See page 10, "System Reset," for instructions on clearing all cards from memory.

The number of beeps indicates the value of each digit. All three

(Warning: master cards cannot be deleted)*

FAAC PR-112S-A User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual