FAAC 1834-080 User Manual

Owner’s Manual
1833, 1834, 1835, 1837 PC Programmable Telephone Entry and Access Control Systems
DoorKing, Inc.
120 Glasgow Avenue
Inglewood, California 90301
U.S.A.
Fax: 310-641-1586 www.doorking.com
P/N 1835-065 REV R, 10/11 Copyright 2003 DoorKing, Inc. All rights reserved.
Page 2 1835-065-R-10-11
Use this manual with the following models only.
1833, 1834, 1835 and 1837 Telephone Entry Systems, REV C or Higher.
DoorKing, Inc. reserves the right to make changes in the products described in this manual without notice and without obligation of DoorKing, Inc. to notify any persons of any such revisions or changes. Additionally, DoorKing, Inc. makes no representations or warranties with respect to this manual. This manual is copyrighted, all rights reserved. No portion of this manual may be copied, reproduced, translated, or reduced to any electronic medium without prior written consent from DoorKing, Inc.
1835-065-R-10-11 Page 3
TABLE OF CONTENTS
Preface
Important Notices......................................................................................................................................................7
General Information..................................................................................................................................................8
Features ..................................................................................................................................................................9
Section 1 – Installation
1.1 General Installation Information................................................................................................................11
1.2 Surface Mount Units.................................................................................................................................12
1.3 Surface Mount Units with Recess Box .....................................................................................................13
1.4 Flush Mount Units.....................................................................................................................................14
1.5 Flush Mount Rough-in Box.......................................................................................................................15
1.6 Flush Mount Trim Ring.............................................................................................................................16
1.7 Flush Mount Surface Mounting Kit ...........................................................................................................17
1.8 Wall Mount Units ......................................................................................................................................18
1.9 Memory Chip Installation..........................................................................................................................19
1.10 Postal Lock Installation.............................................................................................................................20
Section 2 – Wiring
General Information..................................................................................................................................................21
2.1 Wiring Guidelines .....................................................................................................................................22
Terminal Descriptions...............................................................................................................................................23
2.3 Wiring Detail
2.3.1 Controller Only .........................................................................................................................24
2.3.2 Controller and Expansion Boards 1-8 ......................................................................................25
2.3.3 Controller and Expansion Boards 1-16 ....................................................................................26
2.4 RS 232 Cable Connections......................................................................................................................27
Section 3 – Programming
3.1 General Programming Information
3.1.1 Programming with a PC ...........................................................................................................29
3.1.2 Programming from the Keypad ................................................................................................30
3.1.3 System Memory .......................................................................................................................30
3.2 Programming with a PC
3.2.1 Master Code.............................................................................................................................31
3.2.2 Programming the Number of Area Codes Allowed ..................................................................31
3.2.3 Programming for Call Up Operation.........................................................................................32
3.2.4 Programming Resident Elevator Button Relay Time................................................................32
3.2.5 Open Tone On or Off................................................................................................................32
3.2.6 RS-232 Speed Setting..............................................................................................................32
3.2.7 Switch Input Function...............................................................................................................33
3.2.8 Elevator Control Function.........................................................................................................33
3.3 General Programming
3.3.1 Relay Strike Time.....................................................................................................................34
3.3.2 Talk Time..................................................................................................................................34
3.3.3 Tone Open Numbers................................................................................................................35
3.3.4 Switch Input..............................................................................................................................35
3.3.5 Touch-tone / Rotary-dial...........................................................................................................36
3.3.6 Rotary-dial 9.............................................................................................................................36
3.3.7 Single or Multiple Systems.......................................................................................................36
Page 4 1835-065-R-10-11
3.4 Programming Letters, Numbers and Messages
3.4.1 Programming Letters and Numbers.........................................................................................37
3.4.2 Programming the User Message – 1834, 1835 .......................................................................38
3.4.3 Programming the Instruction Message – 1834, 1835 ..............................................................39
3.4.4 Programming the User Message – 1837 .................................................................................40
3.4.5 Programming the Instruction Message – 1837 ........................................................................41
3.5 Programming Phone Numbers and Names .............................................................................................42
3.5.1 Programming the Directory Code Length.................................................................................43
3.5.2 Programming 7-digit Phone Numbers......................................................................................43
3.5.3 Programming Area Codes........................................................................................................44
3.5.4 Programming Phone Numbers with Area Codes .....................................................................44
3.5.5 Programming Names ...............................................................................................................45
3.5.6 Deleting Individual Phone Numbers.........................................................................................45
3.5.7 Delete Names ..........................................................................................................................45
3.5.8 Delete Area Codes...................................................................................................................46
3.5.9 Display Phone Numbers ..........................................................................................................46
3.5.10 Programming PBX Line Access Code .....................................................................................46
3.5.11 Touch-tone Dialing Pause........................................................................................................47
3.6 Device Codes
3.6.1 Programming Device Codes....................................................................................................48
3.6.2 Deleting Device Codes.............................................................................................................48
3.6.3 Enabling Facility Codes............................................................................................................48
3.6.4 Programming Facility Codes....................................................................................................48
3.7 Four-digit Entry Codes
3.7.1 Programming Four-digit Entry Codes.......................................................................................49
3.7.2 Delete Four-digit Entry Codes..................................................................................................49
3.7.3 Entry Code Ranges..................................................................................................................49
3.8 Anti-Pass Back
3.8.1 Programming Anti-Pass Back Mode........................................................................................50
3.8.2 Re-Sync All Devices.................................................................................................................50
3.8.3 Re-Sync Individual Devices .....................................................................................................50
3.8.4 Reset Facility Counter..............................................................................................................50
Section 4 – Adjustments
Circuit Board Adjustments Location .........................................................................................................................51
Circuit Board Adjustment Descriptions and Instructions...........................................................................................52
Section 5 – Operating Instructions
5.1 Guest Instructions ....................................................................................................................................55
5.2 Resident Instructions
5.2.1 Responding to a Guest Call .....................................................................................................56
5.2.2 Using an Entry Code................................................................................................................56
5.3 System Administrator
5.3.1 Opening from a Remote Location ............................................................................................57
5.3.2 Tracker Board Override Hold Open Command........................................................................57
5.3.3 Relay Check.............................................................................................................................58
5.3.4 Time and Date Check ..............................................................................................................58
5.4 Miscellaneous Operating Instructions
5.4.1 Talk Time..................................................................................................................................59
5.4.2 Line Sharing.............................................................................................................................59
5.4.3 Connection to a PBX................................................................................................................59
5.4.4 10-digit Dialing .........................................................................................................................59
1835-065-R-10-11 Page 5
Section 6 – Maintenance and Trouble Shooting
6.1 Trouble Shooting......................................................................................................................................61
6.1.1 RS-232 Test.............................................................................................................................63
6.1.2 Weigand Test...........................................................................................................................64
6.1.3 Elevator Board Hardware Test.................................................................................................64
6.1.4 Elevator Board Floor Hardware Test........................................................................................65
6.1.5 Automatic Hang-up Options.....................................................................................................65
6.2 Accessories..............................................................................................................................................66
6.3 Log Tables................................................................................................................................................67
Page 6 1835-065-R-10-11
IMPORTANT NOTICE
FCC - UNITED STATES
This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of the FCC Rules and Regulations. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
FCC Registration Number: DUF6VT-12874-OT-T
DOC - CANADA
The Canadian Department of Communications label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operational, and safety requirements. The Department does not guarantee the equipment will operate to the users satisfaction.
Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company. The equipment must also be installed using an acceptable means of connection. The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations.
Repairs to certified equipment should be made by an authorized Canadian maintenance facility designated by the supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give the telecommunications company cause to request the user to disconnect the equipment.
Users should ensure, for their own protection, that the electrical ground connections of the power utility, telephone lines, and internal metallic water pipe system, if present, are connected together. This precaution may be particularly important in rural areas.
CAUTION: Users should not attempt to make such connections themselves, but should contact the appropriate electric inspection authority, or electrician, as appropriate.
DOC Registration Number: 1736 4528 A
Notice:
The Load Number (LN) assigned to each terminal device denotes the percentage of the total load to be connected to a telephone loop which is used by the device, to prevent overloading. The termination on a loop may consist of any combination of devices subject only to the requirement that the sum of the load numbers of all the devices does not exceed 100.
Notice:
DoorKing does not provide a power transformer on units sold outside of the United States. Use only transformers that are listed by a recognized testing laboratory to power the telephone entry system. An Inherently Protected Transformer must be used to power this device. 1833, 1834 and 1835 systems require a 16.5-volt, 20 VA transformer. The model 1837 requires a 16.5-volt, 40 VA transformer.
Listing:
This product has been tested to and found to be in compliance with the U.L 294 Safety Standard by Intertek Testing Services NA Inc. (a Nationally Recognized Testing Laboratory) and is ETL listed.
1835-065-R-10-11 Page 7
GENERAL INFORMATION
Prior to beginning the installation of the telephone entry system, we suggest that you become familiar with the instructions, illustrations, and wiring guidelines in this manual. This will help insure that you installation is performed in an efficient and professional manner.
Telcom Access Standards. It is not permissible for customers to use the telcom network lead-in cable to provide the intercom function between the gate and the house. New Zealand Customers: All door and gate entry systems wiring must comply with PTC106: March 2008, Section 9.
The proper installation of the telephone entry panel is an extremely important and integral part of the overall access control system. Check all local building ordinances and building codes prior to installing this system. Be sure your installation is in compliance with local codes.
When used to control a door or pedestrian gate, try to locate the telephone entry system as near as possible to the entry point. The unit should be mounted on a rigid wall to prevent excessive shock and vibration from closing doors or gates. Continuous vibration and shock from slamming doors or spring-loaded pedestrian gates will damage the circuit board. Under no circumstances should the unit be mounted directly to a moving door or gate.
ADA mounting requirements for door control (Ref: ICC/ANSI A117.1-2009).
1. Unobstructed Forward Reach
. Where a clear floor or ground space allows only a forward approach to an object and is unobstructed, mounting height shall be a minimum of 15 inches (381 mm), and a maximum of 48 inches (1.22 m), above the floor or ground to the operable controls.
2. Obstructed High Forward Reach
. If the high forward reach is over an obstruction greater than 20 inches, but less than 25 inches, mounting height shall be a maximum of 44 inches (1.12 m) above the floor or ground to the operable controls.
3. Unobstructed Side Reach
. Where a clear floor or ground space allows a parallel approach to an object and the side reach is unobstructed, and the edge of the clear floor space is 10 inches (255 mm) maximum from the object, mounting height shall be a minimum of 15 inches (380 mm), and a maximum of 48 inches (1.22 m), above the floor or ground to the operable controls.
4. Obstructed High Side Reach
. If the side reach is over an obstruction greater than 10 inches, but less than 24 inches, mounting height shall be a maximum of 46 inches (1.17 m) above the floor or ground to the operable controls.
WARNING: When used to control a vehicular gate with an automatic gate operator, the
telephone entry system must be mounted a minimum of ten (10) feet away from the gate and gate operator, or in such a way that a person cannot operate the entry system and/or touch the gate or gate operator at the same time.
Be sure that the system is installed so that it is not directly in the traffic lane. Goose neck mounting post and kiosks work well for these type systems. When planning where to locate the system, take into consideration traffic lane layouts, turn around lanes for rejected access, conduit runs, power availability, etc.
Environmental factors must also be taken into account. Surface mount units are designed for direct outdoor installation; however it is preferable to protect them from direct exposure to driven rain or snow whenever possible. Flush mount and wall mount units must be protected from direct exposure to the elements. Be sure that ample lighting is provided so that guest can read both the directory and the operating instructions at night.
This telephone entry system contains a number of static sensitive components that can be damaged or destroyed by static discharges during installation or use. Discharge any static prior to removing the circuit board from the lobby panel by touching a proper ground device.
Page 8 1835-065-R-10-11
FEATURES
Can provide service for up to 3000 residents.
Can store up to 8000 card, transmitter or digital PIN codes (not applicable to 1834).
System can be programmed with a PC by modem, RS-232, RS-422 (requires 1508-055
adapters), a LAN connection (requires 1830-175 TCP/IP kit) or via the internet using the Internet Modem Server (use of the IM Server is fee based. Visit
http://www.doorking.com/IMServer
ONE TOUCH CALLING provides the easiest to use system on the market (does not apply to
1833).
System keypad will emit DTMF tones after a call is answered allowing the system to be used
with auto-attendants, answering machines, etc.
Directory codes can be set from 1 to 4 digits in length and can be randomly assigned.
Transaction buffer stores the last 8000 events and has its own backup power source to retain
memory during power outages.
View LIVE transactions.
31-security levels total (security level 00 always denies entry, security level 01 always admits
entry), with 29 programmable security levels, each with four time zones allows you to control and restrict user access as needed (not applicable to 1834).
Programmable holiday schedule (not applicable to 1834).
for more information).
Facility codes can be enabled or disabled. Store up to 10 different facility codes (not
applicable to 1834).
True Anti-Pass Back feature.
Up to 255 programmable area codes (Rev E and higher boards only) allow the system to be
used in areas requiring 10 and 11-digit dialing.
Three internal relays allow the system to control a main entry point plus two additional entry
points (1834 system has only 2 relays).
System can be expanded to control up to 16 entry points in addition to the main entry point.
Tracker expansion boards are required (one for each additional entry point) and are not included with the system. Tracker boards also provide output for door ajar and forced entry alarms (not applicable to 1834).
Optional elevator control board(s) can control up to four elevators with each elevator serving
up to 64 floors (not applicable to 1834).
System will interface with selected models of DKS DoorKing vehicular gate operators to
provide gate operator information and data (requires a Tracker board for each gate operator that is to send data to the system). Not applicable to 1834.
Available in surface, flush or wall mount styles (1833 available in surface or flush mount
only).
1835-065-R-10-11 Page 9
Page 10 1835-065-R-10-11

SECTION 1 - INSTALLATION

Order your telephone line at least two weeks prior to the planned installation date. This will assure that a phone line is available when the unit is installed. The telephone company will require the following information from you:
Type: Touch Tone, Loop Start Ringer Equivalence: 0.0 A Jack Type: RJ11C FCC Registration (US): DUF6VT-12874-OT-T DOC (Canada): 1736 4528 A Electrical Listing: Complies with U.L. 294 - ETL Listed
CALLER ID: You may want to consider ordering caller ID blocking from the telephone company for the entry system phone line. Without caller ID blocking, tenants with the proper phone equipment will be able to identify the telephone number that the entry system is installed on. This may or may not be desirable.

1.1 General Installation Information

1. Open the cabinet of the telephone entry system and disconnect the keypad ribbon cable
from the main circuit board.
2. Remove the 6-32 x 1/2 round head screws from the upper corners of the circuit board.
3. Remove the circuit board by gently pulling it out of the main terminal edge connector.
CAUTION - the circuit board contains static sensitive components. Discharge any static electricity from your hands by touching a proper ground device before removing the circuit board. Place the circuit board where it will not be damaged.
4. Mount the cabinet using the mounting holes provided in the corners. Be sure that
mounting screws do not protrude into the cabinet where they could cause a short on the back of the circuit board. Make any necessary conduit connections using the conduit knockouts provided on the back and/or bottom of the cabinet. DO NOT make any other conduit holes in the cabinet.
5. Route wiring into the cabinet. Do not apply any power at this time.
6. Clean out the cabinet. Be sure that all dirt, metal and/or wood debris is removed from the
cabinet and that the terminal strip edge connector is clean and free of any loose particles.
7. Re-install the circuit board into the cabinet by gently pushing the circuit board terminals
into the edge connector. CAUTION - the circuit board contains static sensitive components. Discharge any static electricity from your hands by touching a proper ground device before removing the circuit board.
8. Secure the circuit board to the cabinet using the screws removed in step 2.
9. Plug the keypad ribbon cable into the circuit board. The cable points down.
1835-065-R-10-11 Page 11

1.2 Surface Mount Units

Surface mount units can be mounted directly to a wall or pilaster, or can be post mounted using a DoorKing Architectural Style mounting post (p/n 1200-037 and 1200-038). Be sure the unit is mounted securely and is not subject to vibration from closing doors or gates.
Standard Surface Mount Housing Case and Mounting Hole Dimensions
4.75
10.125
.25 DIA
1
1.625
10.875
9.0 .875 DIA
1.125
2.625
5.625
11.25
2.625
.875
.875 DIA
13.0
3.25
DOORKING, INC., INGLEWOOD, CA 90301
Surface Mount Case and Mounting Hole
Title:
Dimensions
Date: Dwg. No.
10/05
M1835-065-6
Rev.
B
Page 12 1835-065-R-10-11

1.3 Surface Mount Units with Recess Box

Surface mount units can be semi-flush mounted into a wall or pilaster by using the optional recess­mounting box (p/n 1803-150). Be sure the unit is mounted securely and is not subject to vibration from closing doors or gates.
Standard Surface Mount Recess Mounting Box
13.375
1.625
2.187
10.875
.25 DIA
2.187
1.125.437 2.063
2.687 6.0
10.125
10-24 x 1.25 STUD (4 PL)
9.0
9.0
1.375 DIA
6.0 3.687
3.375
8.5
15.25
3.625
.437
.25 DIA
2.25
4.875
8.375
11.0
13.25
.25 DIA
Rev.
Recess Mount Box
B
3.5
11.375
3.5 2.187
Surface Mount Entry System
DOORKING, INC., INGLEWOOD, CA 90301
Title:
Surface Mount Recess Mounting Box
10/05
Date: Dwg. No.
M1800-065-2
1835-065-R-10-11 Page 13

1.4 Flush Mount Units

Flush mount units are installed into a wall with flush mount kits 1814-165 (stainless) or 1814-166 (gold). Flush mount kits are not included with the entry system. Flush mount units are not designed for direct exposure to the weather. Be sure the unit is mounted securely and is not subject to vibration from closing doors or gates.
Flush Mount Units
1.125
12.0
10.125
.25 DIA
.875
2.625 2.625
5.625
1.625
2.5
.875 DIA
.875 DIA
9.0 .50
11.25
1.125
13.25
10.875
3.0
13.0
DOORKING, INC., INGLEWOOD, CA 90301
Title:
Flush Mount Units
10/05
Date: Dwg. No.
M1800-065-3
Rev.
B
Page 14 1835-065-R-10-11

1.5 Flush Mount Rough-in Box

The flush mount installation kit has two parts; the rough-in box and the trim ring. The rough-in box is installed first.
Flush Mount Rough- in Box
(Flush mount rough-in box is included with the 1814-165 and 1814-166 flush mount kits)
1.685
.275 DIA (3 PL)
12.800
10.120
10-32 x .75 Stud (4 PL)
1.125 DIA (3 PL)
1.500
3.0003.000
6.000 3.400
1.125 DIA (2 PL)
3.400
1.91410.886
1.800
1.800
3.450
.275 DIA (5 PL)
1.300
3.0003.000 3.0003.000
14.600
1.740
1.740
4.700
1.7004.700
DOORKING, INC., INGLEWOOD, CA 90301
Title:
Flush Mount Rough-in Box
4/11
Date: Dwg. No.
M1800-065-4
Rev.
D
1835-065-R-10-11 Page 15

1.6 Flush Mount Trim Ring

Flush mount units can be mounted by using the 1814-165 (stainless) or 1814-166 (gold) mounting kit. Flush mounting kits are not included with the unit. Flush mount units are not designed for direct exposure to the weather. Be sure the unit is mounted securely and is not subject to vibration from closing doors or gates.
Flush Mount Trim Ring ( P/N 1814-165 and 1814-166)
14.700
3.450
10.120
.286 DIA (4 PL)
1.250
1.250 DIA (3 PL)
1.250 DIA (3 PL)
3.000 3.000
1.325
4.5053.100
12.200
3.100
Trim Ring
M1800-065-5
13.555
Entry System
Rev.
D
10.886
16.055
1.575
Rough-in Box
DOORKING, INC., INGLEWOOD, CA 90301
Title:
Flush Mount Trim Ring
4/11
Date: Dwg. No.
Page 16 1835-065-R-10-11

1.7 Flush Mount Surface Mounting Kit

Flush mount units can be surface mounted by using the optional 1814-152 surface mount trim ring. Flush mount units are not designed for direct exposure to the weather. Be sure that the unit is securely mounted and is not subject to vibration from closing doors or gates.
Surface Mount Kit for Flush Style Units
12.0
1.0
.375
2.625
9.0
7.5
6.0
1.125 DIA 1.125 SQ
3.0
13.5
.375
.875
1.125
Flush Mount Ring
DOORKING, INC., INGLEWOOD, CA 90301
Surface Mount Kit for Flush Style Units
Title:
Date: Dwg. No.
3/03
Flush Unit
M1800-065-6
Rev.
A
1835-065-R-10-11 Page 17

1.8 Wall Mount Units

Wall mount units are designed to be mounted directly onto a wall without the need of cutting a large hole as is necessary with flush mount units. Be sure the unit is mounted securely and is not subject to vibration from closing doors or gates.
Wall Mount Housing Case and Mounting Hole Dimensions
.25 DIA
10.875
3.625 3.0 3.0
13.25
10.125
9.0
3.5
15.0
.875 DIA
2.0
DOORKING, INC., INGLEWOOD, CA 90301
Wall Mount Case and Mounting Hole Dimensions
Title:
Date: Dwg. No.
10/05
M1800-065-7
Rev.
B
Page 18 1835-065-R-10-11

1.9 Memory Chip Installation

The telephone entry system is shipped with the memory chips already installed in the unit. However, if you need to change the memory chips (to match an older unit, for example), follow the instructions below.
CAUTION!! Do not install the memory chips with power to the telephone entry system turned on. Attempting to install the memory chips with power on will irrevocably damage the chips. Memory chips are a static sensitive component. Discharge any static electricity from your hands by touching a proper ground device before removing the control board. Handle the memory chips with care.
1. The large memory chip socket is colored black and is located in the center of the circuit board. Be sure that the handle is in the un-locked position (pointing up).
2. Carefully insert the memory chip into the socket. The small half circular indentation on the chip must be at the top. CAUTION: Installing the memory chip upside down will cause permanent damage to the chip. Be sure that the memory chip is seated correctly in the socket, then move the lever on the chip socket to the locked position (down).
3. Install the small memory chip in the socket located at the bottom of the circuit board. The small circular indentation on the chip must be at the top. CAUTION: Installing the memory chip upside down will cause permanent damage to the chip. Be sure that the memory chip is seated correctly in the sock et .
1830 Series Circuit Boards Memory Chip Location
1
1
Dimple on chip must be at top!
1
DOORKING, INC., INGLEWOOD, CA 90301
Title:
1830 Series Memory Chip Location
Date: Dwg. No.
3/03
1835-065-R-10-11 Page 19
M1835-065-1
Rev.
A

1.10 Postal Lock Installation

At some locations, such as gated communities, it will be necessary to provide access to the mail carrier so that they can deliver the mail. Mail carrier access will be provided by the installation of an Arrow Postal Lock. This is the same lock that the Post Office uses for gang mailboxes. These locks are not available to the public. The installer or the building owner/manager will have to call the Post Office and arrange for the installation of this lock into the telephone entry system. All DoorKing commercial telephone entry systems are designed to accept installation of the postal lock.
Prior to installation of the postal lock, be sure power to the telephone entry system is turned off.
1. Remove the hole plug on the faceplate of the telephone entry system.
2. Cut the wire tie wrapped around the micro swit ch next to the postal lock access hole.
3. Remove the two hex nuts from the postal lock-mounting studs. Mount the postal lock on the two studs and secure with the hex nuts.
When the lock is installed, check to be sure that the pawl of the lock, in its extended position, is depressing the micro switch (the micro switch is wired normally closed). When the mail carrier inserts his key and turns the postal lock, the pawl is withdrawn and the micro switch will activate the relay that has been programmed for this function for the programmed strike time.
Postal Lock Installation Detail
2
Micro-switch is wired Normally Closed. Switch is
1
held “open” by tie-wrap or postal lock.
Cut tie-wrap only if postal lock is installed.
2
Micro-switch is pre-wired. Controller terminals are
3
shown for clarification only.
Postal lock supplied by others.
4
Common to Terminal 6 Normally Closed to Terminal 4
1
3
4
DOORKING, INC., INGLEWOOD, CA 90301
Postal Lock Installation Detail
Title:
Date: Dwg. No.
3/03
M1800-065-8
Rev.
A
Page 20 1835-065-R-10-11

SECTION 2 – WIRING

Prior to installing wiring to the telephone entry system, we suggest that you become familiar with the instructions, illustrations, and wiring guidelines in this manual. This will help insure that you installation is performed in an efficient and professional manner.
The wiring of the telephone entry panel is an extremely important and integral part of the overall access control system. Use proper wire for the communication line, power wires, and be sure that the system is properly grounded. Check all local building ordinances and building codes prior to installing this system. Be sure your installation is in compliance with local codes.
Telcom Access Standards. It is not permissible for customers to use the telcom network lead­in cable to provide the intercom function between the gate and the house. New Zealand Customers: All door and gate entry systems wiring must comply with PTC106: March 2008, Section 9.
WARNING: If this telephone entry system is used to control a vehicular gate with an automatic gate operator, the telephone entry system must be mounted a minimum of ten (10) feet away from the gate and gate operator, or in such a way that the user cannot come into contact with the gate or gate operator when using this entry system. If this unit has been installed closer to the automated vehicular gate, do not proceed with any wiring until the unit has been moved and re-installed so that it is in compliance with these instructions.
Use only the supplied transformers (or U.L. listed equivalent) to power the telephone entry and access control system (16.5 VAC, 20 VA for 1833, 1834 and 1835, 16.5 VAC, 40 VA for 1837) and any weigand input devices (16.5 VAC, 20 VA). Do not power any other devices (electric strikes, magnetic locks, etc.) from these power transformers. NOTE: Transformers are not supplied on units sold outside the United States. An Inherently Protected Transformer must be used to power this device. Use only transformers that are listed by a recognized testing laboratory to power the telephone entry system.
For wire runs up to 100 feet, use 18 AWG, 600 volt insulated wire. For wire runs up to 200 feet, use 16 AWG, 600 volt insulated wire. Power wires are susceptible to noise and hum pickup; therefore it is preferable that you keep power wire runs as short as possible.
This telephone entry system contains a number of static sensitive components that can be damaged or destroyed by static discharges during installation or use. Discharge any static prior to removing the circuit board from the lobby panel by touching a proper ground device.
If Tracker expansion boards are being used with this system, refer to the Tracker Installation and Wiring manual that came with the Tracker expansion boards, for detailed information on wiring Tracker boards to the PC programmable telephone entry system.
If Elevator Control is used with this system, refer to the Elevator Control Installation and Wiring manual for detailed information on wiring the elevator control boards to this system and to the elevator push button control panel.
1835-065-R-10-11 Page 21

2.1 Wiring Guidelines

Do not run high voltage (115 V) power lines and communication lines in the same conduit. These should be in separate conduits at least six (6) inches apart. Be sure that all phone line wiring is twisted and completely isolated from ground.
Use only the supplied 16.5 VAC (or U.L. listed equivalent) to power the entry system. An Inhe rently Protected Transformer must be used to power this device. If a s ubstitute transformer is used, it must be listed by a recognized testing laboratory. Do not power any other devices (electric strikes, magnetic locks, lights, etc.) from this transformer. Do not run 16 VAC entry system power lines over 200 feet. It is advisable to keep these wires as short as possible. Use 18 AWG wire for wire runs up to 100 feet, and 16 AWG wire for wire runs up to 200 feet. Install a low voltage surge suppresser (DoorKing p/n 1878-010 or equivalent) to help protect the entry system from power surges.
Weigand wire runs are 500-feet maximum. Use 6-conductor stranded wire with overall shield. 18, 20, 22 or 24 gauge is sufficient for these connections.
A 12 volt .8 amp hour gel-cell battery (DoorKing p/n 1801-008) can be installed in the system to provide stand-by power in the event of a power outage. Two batteries are required, one for the system power and one for the auxiliary terminal power.
Proper grounding of this system is a requirement. The use of surge suppressers can significantly reduce the chance of component failure because of static charges or surges. To be effective, ground connections should be made with a minimum 12 AWG, 600 volt insulated wire to a ground point within 10 feet of the telephone entry system. The ground point must be at an electrical panel, a metallic cold water pipe that runs in the earth, or a stainless steel grounding rod driven at least ten (10) feet into the soil.
Be sure that you use proper wire that has an insulation rated for an underground environment. All wires should be placed in conduits. Proper pre-planning can greatly ease the installation and wiring of this system. Always check with the local building code to determine the type of wire required in your municipality.
The Telephone Entry System is shipped with two (2) Ferrite Filters (1834 systems are shipped with just a single filter). One is installed on the 16 VAC power wires to the main circuit board (terminals 19-20). The second is installed and around the wires connected to the Auxiliary Terminal strip.
To install the ferrite filter, simply snap the filter open, place the wires in the circular core, then
snap the filter closed.
16 VAC POWER AUX TERMINAL WIRES
Page 22 1835-065-R-10-11
Loading...
+ 49 hidden pages