Extron electronics WPD 110 A, WPD 130 A, WPD 120 A, WPS 140A Installation Manual
WPD Series Wallplates • Installation Guide
The Extron WPD Series (WPD 110 A, WPD 120 A, WPD 130 A, and WPS 140A) are single gang
pass-through wallplates with HDMI, DisplayPort, DVI, or VGA connectors and pigtail mounted
rear connectors. All models can be installed in single gang junction boxes, and include a
decorator-style frame. The models are as follows:
• WPD 110 A — HDMI, stereo audio, and control
• HDMI female to HDMI female connector on a pigtail
• 3.5 mm stereo audio jack with 3-pole captive screw connector
• 3-pole captive screw connector (for pass-through signals such as IR and RS-232)
• WPD 120 A — DisplayPort, stereo audio, and control
• DisplayPort female to DisplayPort female connector on a pigtail
• 3.5 mm stereo audio jack with 3-pole captive screw connector
• 3-pole captive screw connector (for pass-through signals such as IR and RS-232)
• WPD 130 A — DVI, stereo audio, and control
• DVI-I female to DVI-I female connector on a pigtail
• 3.5 mm stereo audio jack with 3-pole captive screw connector
• 3-pole captive screw connector (for pass-through signals such as IR and RS-232)
• WPD 140 A — VGA, stereo audio, and control
• 15-pin VGA female connector on a pigtail
• 3.5 mm stereo audio jack with 3-pole captive screw connector
• 3-pole captive screw connector (for pass-through signals such as IR and RS-232)
Install the wallplate directly into the wall using the supplied mud ring or a UL-approved 1-gang
junction box (not supplied). Follow the steps in the “Installation” section on page 2.
Planning - Check the Proposed Installation Location
Before starting the installation it is important that you do the following:
CAUTION:
• Failure to check the items listed below may result in personal injury.
• La non-vérication des éléments listés ci-dessous peut provoquer des blessures.
ATTENTION: Failure to check the items listed below may result in property damage.
Ensure there are no utility cables or pipes at the intended location that might be damaged
or cause injury when you are installing the device.
Check that the installation meets the local and state regulatory requirements, including
building, electrical, and safety codes, and UL and ADA accessibility requirements.
Side View
e
e
A
B
C
A
WPD 110 A
WPD 120 A
WPD 130 A
BC
DVI
e
DISPLAYPORT
ABC
WPD 140 A
e
COMPUTER
ABC
WPD Series Wallplates • Installation Guide (Continued)
During installation ensure the space behind the device
is sufficient for the bend radius of the pigtail. The
recommended minimum bend radii are as follows:
• WPD 110A = 2.0 inches.
• WPD 120A, WPD 130A and WPD 140A = 2.4 inches.
(see image at right)
Installation
1. Using the supplied mud ring or a junction box
(not included) as a guide, mark and cut out the
appropriate material within the marked area.
2. Either:
• Insert the mud ring into the opening, rotate the
locking arms, and secure it with the supplied
screws (as shown at right), or
• Insert the junction box and secure it with nails or
screws.
3. Run the cables (video, audio, IR or RS-232 control)
from the output or input device locations (as
applicable), behind the wall, and to the WPD
location, then thread the cables through the mud
ring or junction box.
4. Video — Insert the HDMI, DisplayPort, DVI, or VGA cable connector into the connector on
the pigtail.
NOTE: If using a DVI display with the WPD 110A, connect a HDMIM-DVIDF adapter and a
separate audio cable.
5. Audio — Secure the output audio cable into the 3-pole captive screw
connector. Wire as described below (see the gure at right). This may
be easier to do before attaching the device to the mud ring.
• For balanced mono audio:
tip (T) = +, ring (R) = -, sleeve (S) = ground
• For unbalanced stereo audio:
tip (T) = left channel, ring (R) = right channel, sleeve (S) = ground
6. Control — 3-pole pass-through connector — Connect applicable cables to the 3-pole
captive screw connector on the rear of the WPD for pass-through signals, such as IR or
RS-232. When connecting the cables, ensure the polarity will be the same as the proposed
input device to avoid crossover and grounding issues.
7. Mount the cabled device into either the mud ring or the junction box and attach the
supplied decorator-style frame.
8. Connect the appropriate input or output devices to the front panel connectors.
9. Test the system and resolve any cabling or signal issues.
T
S
R
Extron
WPD 110 A
Wall Mounting
Bracket
HDM
I
A
B
C
Decorator-Style
Frame
68-2279-01
Rev. C 04 17
e
B
A
C
WPD 130 A
4.1"
(104 mm)
2.37"
(60 mm)
1.41"
(36 mm)
Extron Headquarters
+1.800.633.9876 (Inside USA/Canada Only)
Extron Asia
+65.6383.4400
Extron China
+86.21.3760.1568)
Extron Australia
+61.8.8113.6800
Extron Europe
+31.33.453.4040
Extron Japan
+81.3.3511.7655
Extron Middle East
+971.4.299.1800
Extron India
+91.80.3055.3777
© 2017 Extron Electronics — All rights reserved. All trademarks mentioned are the property of their respective owners. www.extron.com
Loading...