Extron Electronics SGS 408 DVI User Manual

5. Attach the power cord to the SGS 408 and to the AC power

source. Make sure the SGS 408 is working correctly.

6. If the SGS 408 is rack mounted, remove the power cable
from the SGS 408 and reattach the SGS 408 to the rack.
Reconnect the power cord and the input and output cables.

Part Numbers

Related part numbers

Extron Part Part Number

DVI transmitter and DVI receiver 60-316-02

User’s Guide

www.extron.com

Extron Electronics, USA

1230 South Lewis Street
Anaheim, CA 92805
USA

714.491.1500
Fax [phone]

Extron Electronics, Europe

Beeldschermweg 6C
3821 AH Amersfoort
The Netherlands
+31.33.453.4040
Fax [phone]

© 2006 Extron Electronics. All rights reserved.

Extron Electronics, Asia

135 Joo Seng Road, #04-01
PM Industrial Building
Singapore 368363
+65.6383.4400

ax +65.6383.4664

F

Extron Electronics, Japan

Kyodo Building
16 Ichibancho
Chiyoda-ku, Tokyo 102-0082 Japan
+81.3.3511.7655
Fax [phone]

SGS 408 DVI Connector

70-122-01 Upgrade Kit

68-535-01 Rev. C

06 06

Installation

Installing the DVI Connector

The DVI connector card may be installed in the SGS 408 by
following the instructions and illustrations shown below. Before
the DVI connector card can be installed, the internal components
of the SGS 408 must first be accessed.

Internal access

To gain access to the internal components, do the following:

1. Remove the power cable from the SGS 408 and from the
power source.

Do not open the cover of the switcher without unplugging
the power cord.

2. If the SGS 408 switcher is rack mounted, remove the input
and output cables from it and remove the unit from the
rack. If the switcher is not rack mounted, you do not need
to remove the input and output cables.

3. Remove 16 screws from the sides and top of the cover and
two #10 screws from the upper half of the front panel
(figure 1).

Remove (16)
screws from
top and sides.

Installing the DVI connector card

After following the instructions in “Internal access” to remove
the cover, do the following:

1. Remove and retain the two screws that hold the DVI
connector cover in place (figure 2), and set the cover aside.
You will not need it.

After removing the DVI connector cover,
insert the DVI connector through the
opening in the chassis and press
the circuit card evenly into the socket.

Lift cover
straight up

1

FREEZE BLACK

1

BLACK

FREEZE

INPUT

AM

E

PROGR

PREVIEW
TRANSITIONS
CUTTAK

OUTPUT RATE

2

EFFECTS

1

6 7 8

5

M

A

4

R

G

O
R
P

3

2

W

IE

V
E
R

P

3 4 5

2

4

3

8

7

N
IO

T

6

A

IC

N

U

M

M

O
C
P

C

Tx

R

Rx

T

C

N

E

IO

FF

IT

E

S
N
A

TR

SGS 408

SEAMLESS GRAPHIC SWITCHER

Remove #10 screw
(two plcs) each side
of front plate.

Figure 1 — Removing the cover

4. Remove the cover by slightly lifting each side alternately
until the cover is free.

Reverse this procedure to reinstall the cover.

Figure 2 — Installing the DVI connector card

2. Insert the DVI connector through the hole that was created
in the rear panel in step 1.

3. Carefully align the DVI circuit card 50-pin connector with
socket J3 on the SGS 408 circuit board. With the pins
aligned, press down gently on the DVI circuit card. Check
the alignment of the DVI circuit card and socket J3.

Use the two previously removed DVI connector cover
screws to fasten the DVI connector in place.

4. Reinstall the cover of the SGS 408.

SGS 408 DVI Connector • InstallationSGS 408 DVI Connector • Installation

32