Extron electronics SF 26PT Setup Manual

Page 1
SF 26PT • Setup Guide
Product Category
This setup guide contains installation information for the Extron SF 26PT Pendant Speaker.
NOTE: Observe all
applicable building codes and local ordinances when installing the SF 26PT speaker.
NOTE: The 2 speaker
wires of the PendantConnect-2 cable are a red wire with a black stripe (black) and a solid red wire (red). Throughout the rest of this guide the speaker wires are referred to as either being black or red.
NOTE: This speaker is intended for
indoor dry environment only.
Steel Cables (2)
Speaker Wires (2) —
• Red with Black Stripe
• Red
PendantConnect-2 Cable
Speaker
WARNING: Risk of personal injury or
property damage.
The nal installation should be able to
continuously support the speaker weight. The nal installation should also be able to support any short term overloading. Since applications can vary considerably, it is assumed that the installer will exercise good judgment when selecting the mounting location, method, and hardware. Installation and service must be performed by authorized personnel only.
In order to ensure that the cable lock is not
unintentionally unlocked, keep the area within 2 inches of the cable lock in all directions free
of any other objects.
AVERTISSEMENT : Risque de dommages
corporels ou matériels.
L’installation nale doit pouvoir supporter
en permanence le poids de l’enceinte. L’installation nale doit également supporter toute surcharge temporaire. Étant donné la possibilité d’évolution considérable des applications, il est supposé que l’installateur fera preuve de discernement lors de la sélection de l’emplacement, du mode, et du matériel de montage. L’installation et la maintenance du système doivent être exclusivement effectuées par le personnel autorisé.
An d’assurer que le verrou du câble ne
soit involontairement enclenché, libérez l’espace situé dans un intervalle de cinq centimètres autour du verrou de tout autre objet.
Installing the SF 26PT Speaker with the Default Hardware
The SF 26PT speaker assembly includes the SF 26PT speakers with removable top caps, removable grilles, and a 30-foot length of PendantConnect-2 (PCC-2) suspension cable that incorporates both the speaker wires and two steel support cables.
Installation requires attaching two steel cables to a suitable mounting point, such as a pipe or eye bolt, attaching the swaged ends of the cables to a hook for the speaker, and routing the two speaker wires to the 2-pole splicing connectors on the speaker. Follow the steps below to properly install the speaker. Locate a suitable permanent mounting location for the SF 26PT where the two support cables can be securely attached.
NOTE: The structural member of the building must
be able to support the complete speaker assembly including the speaker and cap, support cables, the speaker grille, and any optional accessories. See the
Warning at the beginning of this guide.
NOTE: To help determine the necessary length of
PCC-2 cable needed, if pre-cutting, refer to the “Reference Information” section of the user guide, otherwise follow the numbered steps below.
NOTE: The speaker comes in a bag that helps to keep
the speaker clean during installation.
Installing the Mounting Hardware
1. Locate a suitable mounting point for the SF 26PT, such
as a pipe or an eye bolt.
2. After determining the longest length of the two support
cables that will be needed to attach the speaker to the structure attachment points, cut the 30-foot PCC-2 cable so that the 2 steel cables and 2 speaker wires are all of the same length.
ATTENTION: Do not use regular wire cutters
to cut through the steel cable. Ordinary wire cutters may be damaged when attempting to cut through the steel cable. You must use a suitable cable cutter to cut the steel cable.
ATTENTION : N’utilisez pas de cisaille standard
pour couper le câble en acier. Ce type de cisaille peut être endommagé lors de la coupe du câble en acier. Vous devez utiliser une pince coupe­câble adaptée à ce type de câble.
NOTE: Be sure to allow extra cable length for the
structure attachment points
1
Page 2
SF 26PT • Setup Guide (Continued)
0.43" (11 mm)
DO NO
0.43" (11 mm)
DO NO
NOTE: For optional speaker hanging methods,
see Optional Ceiling Bracket Kit, Optional
2-cable Installation Kit, and Optional 4-cable Installation Kit.
3. Strip back as much of the PCC-2 outer jacket as needed.
4. If the optional ceiling bracket is being installed, see
Optional Ceiling Bracket Kit on page 4, otherwise continue
with the next step.
5. At the structure attachment point end of the support cables,
route the cut end of one cable through one end of the cable lock 1, then route the cable around or through the attachment structure 2 using as much cable as needed to allow the speaker to be positioned at the correct height. An attachment example is shown below. Do this step for both cables.
Steel Cable
22
C
3
3
1
1
Cable Lock
2"
1"
2" min.
6. After ensuring that the cable is of sufcient length to
position the speaker at the proper installation height, run the free end of the cable through the open end of the cable lock 3 and secure it in place, as shown above. Do this step for both cables.
NOTE: In order to ensure that the cable lock is not
unintentionally unlocked, keep the area within 2 inches of the cable lock in all directions free of any other objects. See the Warning at the beginning of this guide.
8. Lift one lever of one 3-pole splicing connector 1 and
insert the stripped end of the red speaker wire into an empty pole of the connector 2. Press the lever down to lock the red wire in place 3.
33
2
2
11
Do the same with the second 3-pole splicing connector for the black speaker wire.
9. Connect the speaker/amplier wires to the 3-pole
splicing connectors in step 8.
a. Strip 0.43 inch (11 mm) from the ends of the black
and red amplier wires. These wires will be inserted into the two 3-pole splicing connectors.
T TIN the wires.
b. The red speaker/amplier wire connects to the
splicing connector wired to the red wire, and the black speaker/amplier wire coming from the junction box connects to the splicing connector wired to the black wire.
NOTE: Each pole of the splicing connector is
capable of accepting up to 12 AWG wire.
10. When daisy-chaining speakers, wire the 3-pole splicing
connectors for a Loop-through conguration.
Loop-through:
Red Wire (+) from Previous Speaker/Amplifier
Red Wire (+) to Next Speaker
Red Wire (+) to Speaker
7. To connect the speaker wires to the amplifier:
On the cut end of the PCC-2 cable, strip 0.43 inch (11 mm) from the ends of the protruding black and red wires. These wires will be inserted into the two 3-pole splicing connectors (included).
T TIN the wires.
2
Black Wire (-) from Previous Speaker/Amplifier
Black Wire (-) to Next Speaker
Black Wire (-) to Speaker
Page 3
r
.43" (11 mm)
DO NO
g
NOTE: Wiring is the same for all hanging methods
where PCC-2 cable is used. If it is not used, the 2-pole splicing connectors at the speaker should be replaced with the provided 3-pole splicing connectors. Refer to Speaker Installation and
Configuration for details.
NOTE: Setting the tap switch is the same for all
installation metnods.
Product Category
11
2
2
Do the same for the black speaker wire.
5. The speaker wires are now connected at the back of
the speaker.
3
3
Speaker Installation and Configuration
1. Attach the swaged ends of the steel cables through the
speaker cover 1 and onto the speaker hook 2 on the top of the speaker, as shown here.
Speaker Cap
11
PendantConnect-2 Cable
2
2
Speake Hook
2. The top of the speaker has a red and a black speaker wire
with 2-pole splicing connectors attached.
3. Using the guide printed on the side of the splicing
connector, strip .43 inch (11 mm) from the ends of the red and black speaker wires coming from the cable. These wires will be inserted into the 2-pole splicing connectors
of the speaker.
2-Pole Splicing Connectors
Remove and properly dispose of the bag.
6. To set the tap selector switch, use the provided grille
hook to rst remove the speaker grille. Insert the small end of the hook through any perforation along the outer edge of the grille and pull the grille off the speaker.
Enclosure
Cloth Scrim Backin
T TIN the wires.
4. Lift the splicing connector lever 1 and insert the stripped
end of the red wire into the empty pole of the connector
that is attached to the red wire coming from the
2
speaker. Press the lever down to lock the red wire in place
.
3
Speaker Grille
Grille Hook
7. Use a Tweeker or small screwdriver to set the tap
selector switch to the desired position.
3
Page 4
SF 26PT • Setup Guide (Continued)
Optional Ceiling Bracket Kit
16W
100 V
32W 64W
OFF
OFF
64W 32W
70 V
16W
8Ω
8W
The optional SMK C SF 26PT Extron Ceiling Bracket Kit allows the SF 26PT speaker assembly to be suspended from a octagon junction box. The kit consists of two ceiling brackets and matching magnetic covers.
Steel Cables
Adjust the Tap Selector
8. Replace the grille.
NOTE: Wiring is the same for all hanging methods
NOTE: Setting the tap switch is the same for all
NOTE: Follow steps 1 through 2 of the Installing
NOTE: Be sure to allow extra cable length for the
where PCC-2 cable is used. If it is not used, the 2-pole splicing connectors at the speaker should be replaced with the provided 3-pole splicing connectors. Refer to Speaker Installation and
Configuration for details.
installation metnods.
the Mounting Hardware section before
continuing with any of the optional mounting methods.
structure attachment points
Ceiling Bracket
4
4
Cover Plate
PendantConnect-2 Cable
3
3
2
2
11
3-Pole Splicing Connector
Speaker Wires
Cable Lock
Cable Lock Release
Min. 1”
Side View
1. Install and wire an octagon junction box where the
ceiling bracket is to be attached.
NOTE: The junction box must be attached to a
permanent structural member of the building and be able to support the complete speaker assembly including the speaker and cap, cable, and the ceiling bracket and cover plate. See the Warning at the beginning of this guide.
2
2
3
3
4
4
Grommet
2. Route the free end of the PCC-2 cable through the
ceiling bracket cover 1 with the magnetic side of the cover facing the ceiling bracket.
3. Keeping in mind how much speaker wire and steel
cable will be required, remove as much of the PCC­2 cable jacket as necessary such that the end of the jacket remains ush with the top of the black center
grommet 2 of the ceiling bracket.
4. Route the free ends of the two steel support cables
through the two ceiling bracket cable locks 4. Inserting the steel cable through the bottom of the cable lock will lock the cable in place. Pressing the cable lock release will unlock the cable.
NOTE: A minimum of 1" (25.4 mm) of steel cable
must protrude from the top of the cable lock.
4
Page 5
Product Category
x
Three Mounting Points
ATTENTION: Do not use regular wire cutters
to cut through the steel cable. Ordinary wire cutters may be damaged when attempting to cut through the steel cable. You must use a suitable cable cutter to cut the steel cable.
ATTENTION : N’utilisez pas de cisaille standard
pour couper le câble en acier. Ce type de cisaille peut être endommagé lors de la coupe du câble en acier. Vous devez utiliser une pince coupe­câble adaptée à ce type de câble.
5. Attach the ceiling bracket to the junction box using two
screws with the splicing connectors inserted into the junction box.
Junction Bo
Ceiling Bracket
Screw
Optional 2-Cable Installation Kit
The optional Extron SMK A 2C 2-aircraft cable installation kit allows the SF 26PT speaker to be suspended from 3 overhead points such as a pipe or eye bolt using the 2 included PCC-2 steel cables and the 2 additional cables from the kit.
0° Vertical
4
4
11
Steel Cables (2)
2
2
2" min.
45°
45°
5
5
PCC-2
45°
Cable Lock
3
3
Ceiling Bracket Cover Plate
6. Attach the ceiling bracket cover onto the ceiling
bracket. Two small magnets secure the cover plate in place.
1. Route the cut end of both PCC-2 steel cables to an
overhead anchor point 1 using the cable locks to secure the cables in place.
NOTE: The angle between those PCC-2 steel
cables and the 0° vertical position directly above the speaker is 45°.
2. Route the two cables from the kit to overhead mounting
locations such that angle between those cables 2 and the 0° vertical position directly above the speaker is 45°.
3. The angle between each of the 3 cables and its
adjacent cable is 120°.
4. Use cable locks to secure both cables from the kit to
the mounting locations 3.
NOTE: In order to ensure that the cable lock is not
unintentionally unlocked, keep the area within 2 inches of all cable lock in any direction free of any other objects. See the Warning at the beginning of this guide.
5. Connect the 4 swaged steel cable ends (2 from the
PCC-2 cable and 2 from the kit) through the speaker cap and to the hook 5 .
5
Page 6
Optional 4-Cable Installation Kit
Four Mounting Points
Five Mounting Points
Five mounting points
The optional Extron SMK A 4C 4-aircraft cable installation kit allows the SF 26PT speaker to be suspended from 4 overhead points or 5 overhead points such as a pipe or eye bolt (when also using the PCC-2 cable).
0° Vertical
Speaker
45°11
Wires (2)
2
2
Cable Lock
Steel Cables (4)
2" min.
45°
45°
3
3
45°
0° Vertical
4
4
PCC-2
45°
45°
11
5
5
45°
45°
3
3
Cable Lock
Steel Cables (4)
2
2
2" min.
1. Route the cut end of both PCC-2 steel cables to an
overhead anchor point 1 using the cable locks to secure the cables in place.
2. Route the four cables from the kit to the overhead
Four mounting points
1. Route the four cables from the kit to overhead mounting
locations such that the angle between each cable and the vertical position directly above the speaker is 45°
2. The angle between each of the 4 cables and its adjacent
cable is 90°.
3. Use cable locks to secure the 4 cables from the kit to the
mounting locations 2.
NOTE: In order to ensure that all cable locks are
not unintentionally unlocked, keep the area within 2 inches of all cable locks in any direction free of any other objects. See the Warning at the beginning of this guide.
4. Connect the 4 swaged steel cable ends from the kit
through the speaker cap and to the hook 3.
For information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, see the
Extron Safety and Regulatory Compliance Guide on the Extron website.
© 2018 Extron Electronics All rights reserved. All trademarks mentioned are the property of their respective owners. www.extron.com
6
1.
mounting locations 2 such that angle between those cables and the 0° vertical position directly above the speaker is 45°.
3. The angle between each of the 4 kit cables and its
adjacent cable is 90°.
4. Use cable locks to secure the 4 cables from the kit to
the mounting locations 3.
NOTE: In order to ensure that the cable lock is not
unintentionally unlocked, keep the area within 2 inches of all cable locks in any direction free of any other objects. See the Warning at the beginning of this guide.
5. Connect the 6 swaged steel cable ends (2 from the
PCC-2 cable and 4 from the kit) through the speaker cap and to the hook 5.
NOTE: See the user guide for painting instructions.
See the SF 26PT User Guide for further details.
68-3135-50
Rev. A
10 18
Loading...