Extron Electronics RM 1 User Manual

RM 1 • Installation Guide

TLP PRO 520M

Refer to www.extron.com for the complete
TLP Pro 320m and TLP Pro 520M user guide

and installation instructions before

connecting the product to the power source.

Overview

This guide provides instructions for an experienced, professional installer to mount and install the Extron
TLPPro320M or TLP Pro 520M TouchLink® panel using the RM 1 rack mounting plate. This plate ts into a standard
19-inch equipment rack, with 3U of vertical space. For complete instructions about installing and calibrating the
TouchLink panel, see the TLPPro320M User Guide or the TLP Pro 520M User Guide at

www.extron.com.

ATTENTION: The installation shall be in accordance with the applicable provisions of National Electrical Code

ANSI/NFPA 70, article 725 and the Canadian Electrical Code part 1, section 16.

NOTE: The diagram below shows the TLP Pro 520M. The TLP Pro 320M is mounted in exactly the same way.

Preparing and Installing the RM 1 Mounting Kit

To mount the TLP Pro TouchLink
touchpanel in any standard 19-inch
equipment rack, follow these
instructions:

1. If necessary, disconnect any cables

that are attached to the touchpanel.

2. Run cables to the rack. Provide

some slack in the cable for installing
the touchpanel.

3. Secure the RM 1 rack mounting

plate to the rack using the provided
#10-32 rack mount screws (a in
the gure to the right).

RM 1

1

Secure the RM 1 to
the rack with the four
#10-32 screws provided.

Mounting the Touchpanel

Extron Headquarters

+1.800.633.9876 (Inside USA/Canada Only)

Extron USA - West Extron USA - East
+1.714.491.1500 +1.919.850.1000
+1.714.491.1517 FAX [phone] FAX

© 2014 Extron Electronics — All rights reserved. All trademarks mentioned are the property of their respective owners. www.extron.com

Wall Plate Adapter

1. Align the four mounting holes of

the wall plate adapter (one in each
corner) with the four mounting holes
on the RM1.

2. Use the four provided mounting

3

TLP Pro 520M snaps onto
the wall plate adapter
(2 places on each side).

2

Secure the wall adapter plate to the
RM 1 with the provided screws (4).

screws (#6-32 x 0.375 inches) to
secure the wall plate adapter to the nut inserts in the RM1 (bin the gure to the right). Do not overtighten the
screws.

3. Snap the touchpanel to the wall plate adapter (

4. Connect the cables to the back of the touchpanel. If necessary, carry out an initial calibration of the TouchLink

in the gure to the right).

c

panel. For complete instructions about cabling and calibration, see the TLPPro320M User Guide or the
TLPPro520M User Guide at www.extron.com.

Extron Europe

+800.3987.6673
(Inside Europe Only)

+31.33.453.4040
+31.33.453.4050 FAX

Extron Asia

+65.6383.4400
+65.6383.4664 FAX

Extron Japan

+81.3.3511.7655
+81.3.3511.7656 FAX

Extron China

+86.21.3760.1568
+86.21.3760.1566 FAX

Extron Middle East

+971.4.299.1800
+971.4.299.1880 FAX

Extron Korea

+82.2.3444.1571
+82.2.3444.1575 FAX

Extron India

1800.3070.3777
Inside India Only

+91.80.3055.3777
+91.80.3055.3737 FAX

68-2299-01 Rev. A

02 14