Extron Electronics RGB 192V Setup Guide

Setup Guide — RGB 190FV and RGB 192V

witch 2 (item ).

Setup Guide — RGB 190FV and RGB 192V, cont’d

This guide provides quick start instructions for an experienced installer to set up and operate Extron® RGB 190FV and RGB 192V analog computer-video interfaces. The RGB 192V also has audio capabilities.

Installation

Step 1 — Mounting

Turn off or disconnect all equipment power sources and mount the interface as required. With optional mounting kits, it can be mounted under or through a desk or other furniture.

Step 2 — Connections

The drawing below shows an RGB 192V. With the exception of audio features (marked with

an asterisk [*] in the callout), the features described in step 2 apply to both models.

8 2*

POWER

12-15V

1A MAX.

AUDIO

1 3 69

C O MP UT ER

I N PU T M O NI TO R

H - SH IF T

R G B 1 9 2

SE RR

LE VE L

SO G

Computer Input — Connect a computer-video source to this female 15-pin HD connector.

Audio input (RGB 192V only) — Connect an unbalanced

stereo audio source to this 3.5 mm mini stereo jack for

Tip (Left) Sleeve (Gnd)

unbalanced audio input.

Monitor connector — If desired, connect a local monitor or

other device to this female 15-pin HD connector.

BNC output connectors — Connect a display to these rear

panel BNC connectors as shown in the ﬁgure below.

RGBHV

RGsB

Stereo audio output connector (RGB 192V only) — Connect an audio device, such

as powered speakers, to this 3.5 mm, 5-pole captive screw connector for balanced or

RGBS

For RGsB video, also select the

NOTE

SOG option using DIP s

Ring (Right)

unbalanced stereo or mono audio output.

For unbalanced audio output, connect the sleeve(s) to the ground contact.

DO NOT connect the sleeve(s) to the negative (-) contacts).

Tip

Ring

Sleeve (s)

Tip

Ring

Balanced Stereo OutputUnbalanced Stereo Output

Do not tin the wires!

Tip

NO GROUND HERE.

Sleeve(s)

Tip

NO GROUND HERE.

L R

L/MONO

345

AUDIO

L R

DD SP NO M O N. M. A UD IO

5*7

Tip (Left)

Sleeve (Gnd)

Conﬁgure the interface for stereo or mono output using rear panel DIP switch 6 in item f,

DIP switches, below. When Mono is selected, the right and left inputs are combined and placed on the left output connectors.

DIP switches — This bank of DIP switches conﬁgures the interface as shown in the

following table. Default position for all switches is off (down).

Switch On (up) Off (down) 1 — Level and peaking 2 — SOG 3 — Serration pulses 4 — DDSP 5 — No monitor

0.8 V p-p, 15% peaking Unity (0.7 V) p-p, no peaking Sync on green (RGsB) RGBHV or RGBS Serration pulses present No serration pulses Bypass sync processing Allow sync processing No local monitor connected

Local monitor connected

ID bits 4 and 11 grounded

6 — Mono audio

Mono on left channel only Stereo

(spare for RGB 190FV)

Power connector — Connect an IEC power cord

between the included 12 V power supply and a 100 VAC/240 VAC, 50-60 Hz source. Connect the power

Smooth

supply to the interface as shown at right.

This product is intended to be supplied by a Listed

Power Unit marked “Class 2” or “LPS”, rated 12 VDC, 1.0 A minimum. Always use a power supply supplied by or speciﬁed by Extron. Use of

SECTION A–A

an unauthorized power supply voids all regulatory compliance certiﬁcation and may cause damage to the supply and the end product. Unless otherwise stated, the AC/DC adapters are not suitable for use in air handling spaces or in wall cavities. The installation must always be in accordance with the applicable provisions of National Electrical Code ANSI/NFPA 70, article 75 and the Canadian Electrical Code part 1, section 16. The power supply shall not be permanently ﬁxed to a building structure or similar structure.

Operation

After all devices are powered up, the system is fully operational. If any problems are encountered, verify that the cables are routed and connected properly. If your problems persist, call the Extron S3 Sales & Technical Support Hotline that is closest to you, at the number shown below.

Power indicator —

Amber — Indicates power is applied. Green — Indicates that power is applied and a sync signal is present on the input.

H(orizontal) Shift — While viewing the displayed image, rotate this control to move

the image to the right or left on the screen.

N 

Extron USA - West

Headqua rters

+800.6 33.9876

Inside USA / Canada Only

+1.714.491.1500 +1.714.491.1517 FAX

DDSP disables the interface’s Horizontal Shift control.

To use the display’s centering controls rather than the interface’s controls, set the DDSP DIP switch to On (up).

Extron USA - East

+800.6 33.9876

Inside USA / Canada Only

+1.919.863.1794 +1.919.863.1797 FA X

Extron Euro pe

+800.3 987.6673

Inside Europe Only

+31.33.4 53.4040 +31.33.4 53.4050 F AX

Extron Asia

+800.7 339.8766

Inside Asia Only

+65.63 83.440 0 +65.63 83.466 4 FAX

Extron Japa n

+81.3.35 11.7655 +81.3.35 11.7656 FAX

Extron Chi na

+400. 883.1568

Inside China Only

+86.21. 3760.1568 +86.21. 3760.1566 FA X

Extron Mid dle East

+971.4.2 991800 +971.4.2 991880 FA X

Power Supply

Output Cord

Ridges

A A

Rev. A 03 10

Captive

Screw

Connector

Tie Wrap

3" 16 (5 mm) Max.

68-647-50