Extron electronics FOX 3G HD-SDI SM, FOX 3G HD-SDI MM, FOX 3G HD-SDI P SM User Manual

Fiber Optic Transceivers

FOX 3G HD-SDI

Multi-Rate HD-SDI / SDI Fiber Optic Transceiver

User Guide

68-1384-01 Rev. C

10 17

Safety Instructions

Safety Instructions • English

WARNING: This symbol, , when used on the product, is intended to

alert the user of the presence of uninsulated dangerous voltage within
the product’s enclosure that may present a risk of electric shock.

ATTENTION: This symbol, , when used on the product, is intended

to alert the user of important operating and maintenance (servicing)
instructions in the literature provided with the equipment.

For information on safety guidelines, regulatory compliances, EMI/EMF
compatibility, accessibility, and related topics, see the Extron Safety and
Regulatory Compliance Guide, part number 68-290-01, on the Extron
website, www.extron.com.

Istruzioni di sicurezza • Italiano

AVVERTENZA: Il simbolo, , se usato sul prodotto, serve ad

avvertire l’utente della presenza di tensione non isolata pericolosa
all’interno del contenitore del prodotto che può costituire un rischio di
scosse elettriche.

ATTENTZIONE: Il simbolo, , se usato sul prodotto, serve ad

avvertire l’utente della presenza di importanti istruzioni di funzionamento
e manutenzione nella documentazione fornita con l’apparecchio.

Per informazioni su parametri di sicurezza, conformità alle normative,
compatibilità EMI/EMF, accessibilità e argomenti simili, fare riferimento
alla Guida alla conformità normativa e di sicurezza di Extron, cod. articolo
68-290-01, sul sito web di Extron, www.extron.com.

Sicherheitsanweisungen • Deutsch

WARNUNG: Dieses Symbol auf dem Produkt soll den Benutzer

darauf aufmerksam machen, dass im Inneren des Gehäuses dieses
Produktes gefährliche Spannungen herrschen, die nicht isoliert sind und
die einen elektrischen Schlag verursachen können.

VORSICHT: Dieses Symbol auf dem Produkt soll dem Benutzer in

der im Lieferumfang enthaltenen Dokumentation besonders wichtige
Hinweise zur Bedienung und Wartung (Instandhaltung) geben.

Weitere Informationen über die Sicherheitsrichtlinien, Produkthandhabung,
EMI/EMF-Kompatibilität, Zugänglichkeit und verwandte Themen finden Sie in
den Extron-Richtlinien für Sicherheit und Handhabung (Artikelnummer
68-290-01) auf der Extron-Website, www.extron.com.

Instrucciones de seguridad • Español

ADVERTENCIA: Este símbolo, , cuando se utiliza en el producto,

avisa al usuario de la presencia de voltaje peligroso sin aislar dentro del
producto, lo que puede representar un riesgo de descarga eléctrica.

ATENCIÓN: Este símbolo, , cuando se utiliza en el producto, avisa

al usuario de la presencia de importantes instrucciones de uso y
mantenimiento recogidas en la documentación proporcionada con el
equipo.

Para obtener información sobre directrices de seguridad, cumplimiento
de normativas, compatibilidad electromagnética, accesibilidad y temas
relacionados, consulte la Guía de cumplimiento de normativas y seguridad
de Extron, referencia 68-290-01, en el sitio Web de Extron, www.extron.com.

Instructions de sécurité • Français

AVERTISSEMENT : Ce pictogramme, , lorsqu’il est utilisé sur le

produit, signale à l’utilisateur la présence à l’intérieur du boîtier du
produit d’une tension électrique dangereuse susceptible de provoquer
un choc électrique.

ATTENTION : Ce pictogramme, , lorsqu’il est utilisé sur le produit,

signale à l’utilisateur des instructions d’utilisation ou de maintenance
importantes qui se trouvent dans la documentation fournie avec le
matériel.

Pour en savoir plus sur les règles de sécurité, la conformité à la
réglementation, la compatibilité EMI/EMF, l’accessibilité, et autres sujets
connexes, lisez les informations de sécurité et de conformité Extron, réf.
68-290-01, sur le site Extron, www.extron.com.

Instrukcje bezpieczeństwa • Polska

OSTRZEŻENIE: Ten symbol, , gdy używany na produkt, ma na celu

poinformować użytkownika o obecności izolowanego i niebezpiecznego
napięcia wewnątrz obudowy produktu, który może stanowić zagrożenie
porażenia prądem elektrycznym.

UWAGI: Ten symbol, , gdy używany na produkt, jest przeznaczony do

ostrzegania użytkownika ważne operacyjne oraz instrukcje konserwacji
(obsługi) w literaturze, wyposażone w sprzęt.

Informacji na temat wytycznych w sprawie bezpieczeństwa, regulacji
wzajemnej zgodności, zgodność EMI/EMF, dostępności i Tematy pokrewne,
zobacz Extron bezpieczeństwa i regulacyjnego zgodności przewodnik, część
numer 68-290-01, na stronie internetowej Extron, www.extron.com.

Инструкция по технике безопасности • Русский

ПРЕДУПРЕЖДЕНИЕ: Данный символ, , если указан

на продукте, предупреждает пользователя о наличии
неизолированного опасного напряжения внутри корпуса
продукта, которое может привести к поражению электрическим
током.

ВНИМАНИЕ: Данный символ, , если указан на продукте,

предупреждает пользователя о наличии важных инструкций
по эксплуатации и обслуживанию в руководстве,
прилагаемом к данному оборудованию.

Для получения информации о правилах техники безопасности,
соблюдении нормативных требований, электромагнитной
совместимости (ЭМП/ЭДС), возможности доступа и других
вопросах см. руководство по безопасности и соблюдению
нормативных требований Extron на сайте Extron: ,

www.extron.com, номер по каталогу - 68-290-01.

安全说明 • 简体中文

警告： 产品上的这个标志意在警告用户该产品机壳内有暴露的危险 电压，

有触电危险。

注意： 产品上的这个标志意在提示用户设备随附的用户手册中有

重要的操作和维护(维修）说明。

关于我们产品的安全指南、遵循的规范、EMI/EMF 的兼容性、无障碍
使用的特性等相关内容，敬请访问 Extron 网站 , www.extron.com，参见

Extron 安全规范指南，产品编号 68-290-01

。

安全記事 • 繁體中文

警告: 若產品上使用此 符號，是為了提醒使用者，產品機殼內存在著

可能會導致觸電之風險的未絕緣危險電壓。

注意 若產品上使用此符號，是為了提醒使用者，設備隨附的用戶手冊中有

重要的操作和維護（維修）説明。

有關安全性指導方針、法規遵守、EMI/EMF 相容性、存取範圍和相關主題的詳細資
訊，請瀏覽 Extron 網站：www.extron.com，然後參閱《Extron 安全性與法規
遵守手冊》，準則編號 68-290-01。

安全上のご注意

• 日本語

警告: この記 号 が製品上に表示されている場合は、筐体内に絶縁されて

いない高電圧が流れ、感電の危険があることを示しています。

注意:この記号 が製品上に表示されている場合は、本機の取扱説明書に

記載されている重要な操作と保守( 整備)の 指示についてユーザーの注 意
を喚起するものです。

安全上のご注意、法規厳守、EMI/EMF適合性、その他の関連項目に
つ い て は 、エ ク ストロ ン の ウ ェブ サ イト www.extron.com よ り 『 Extron Safety
and Regulatory Compliance Guide』 ( P/N 68-290-01) をご覧ください。

안전 지침 • 한국어

경고: 이 기호 가 제품에 사용될 경우, 제품의 인클로저 내에 있는

접지되지 않은 위험한 전류로 인해 사용자가 감전될 위험이 있음을
경고합니다.

주의: 이 기호 가 제품에 사용될 경우, 장비와 함께 제공된 책자에 나와

있는 주요 운영 및 유지보수(정비) 지침을 경고합

안전 가이드라인, 규제 준수, EMI/EMF 호환성, 접근성, 그리고 관련 항목에
대한 자세한 내용은 Extron 웹 사이트(www.extron.com)의 Extron 안전 및
규제 준수 안내서, 68-290-01 조항을 참조하십시오.

니다.

Copyright

© 2017 Extron Electronics. All rights reserved.

Trademarks

All trademarks mentioned in this guide are the properties of their respective owners.

The following registered trademarks®, registered service marks(SM), and trademarks(TM) are the property of RGBSystems, Inc. or Extron
Electronics (see the current list of trademarks on the

Cable Cubby, ControlScript, CrossPoint, DTP, eBUS, EDID Manager, EDID Minder, Flat Field, FlexOS, GlobalViewer, Global Configurator, Global Scripter,
Hideaway, IP Intercom, IP Link, Key Minder, LinkLicense, LockIt, MediaLink, MediaPort, NetPA, PlenumVault, PoleVault, PowerCage, PURE3, Quantum,
SoundField, SpeedMount, SpeedSwitch, System INTEGRATOR, TeamWork, TouchLink, V-Lock, VoiceLift, VN-Matrix, WallVault, WindoWall, XTP, and
XTP Systems

(SM)

Registered Service Mark

AAP, AFL (Accu-RATE Frame Lock), ADSP - Advanced Digital Sync Processing, Auto-Image, CableCover, CDRS - Class D Ripple Suppression, Codec
Connect, DDSP (Digital Display Sync Processing), DMI (Dynamic Motion Interpolation), Driver Configurator, DSP Configurator, DSVP (Digital Sync
Validation Processing), eLink, Entwine, EQIP, EverLast, FastBite, FOX, FOXBOX, HyperLane, IP Intercom HelpDesk, MAAP, MicroDigital, Opti-Torque,
ProDSP, QS-FPC - QuickSwitch Front Panel Controller, Room Agent, Scope-Trigger, ShareLink, Show Me, SIS (Simple Instruction Set), Skew-Free,
SpeedNav, StudioStation, Triple-Action Switching, True4K, Vector™ 4K, VideoLounge, WebShare, XTRA, ZipCaddy, and ZipClip

: S3 Service Support Solutions

Terms of Use page at www.extron.com):

Registered Trademarks

Trademarks

(®)

(™)

FCC Class A Notice

This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part15 of the FCC rules. The ClassA limits provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is
likely to cause interference. This interference must be corrected at the expense of the user.

NOTE: For more information on safety guidelines, regulatory compliances, EMI/EMF

compatibility, accessibility, and related topics, see the Extron Safety and Regulatory

Compliance Guide on the Extron website.

Class 1 Laser Product

Any service to this product must be carried out by Extron Electronics and its qualified
service personnel.

CAUTION: Using controls, making adjustments, or performing procedures in a manner

other than what is specified herein may result in hazardous radiation exposure.

NOTE: For more information on safety guidelines, regulatory compliances,

EMI/EMF compatibility, accessibility, and related topics, see the “Extron Safety and

Regulatory Compliance Guide” on the Extron website.

Produit laser de classe1

Si ce produit a besoin d’un quelconque entretient, celui-ci doit être fait par
ExtronElectronics et son personnel qualifié.

ATTENTION : L’utilisation de commandes, la réalisation de réglages, ou l’exécution de

procédures de manière contraire aux dispositions établies dans le présent document,
présente un risque d’exposition dangereuse aux radiations.

Remarque : Pour plus d'informations sur les directives de sécurité, les conformités

de régulation, la compatibilité EMI/EMF, l'accessibilité, et les sujets en lien, consultez le
«Informations de sécurité et de conformité Extron» sur le site internet d'Extron.

Conventions Used in this Guide

Notifications

The following notifications are used in this guide:

WARNING: Potential risk of severe injury or death.
AVERTISSEMENT : Risque potentiel de blessure grave ou de mort.

CAUTION: Risk of minor personal injury.
ATTENTION : Risque de blessuremineure.

ATTENTION:

• Risk of property damage.

• Risque de dommages matériels.

NOTE: A note draws attention to important information.

Specifications Availability

Product specifications are available on the Extron website, www.extron.com.

Extron Glossary of Terms

A glossary of terms is available at http://www.extron.com/technology/glossary.aspx.

Contents

Introduction ...............................................1

About this Manual................................................ 2

About the FOX 3G HD-SDI .................................. 2

Transceiver Configurations ............................... 2

Features .............................................................. 4

Installation and Operation .........................6

Installation Overview ............................................ 6

Connections and Settings.................................... 6

Operation .......................................................... 10

Front Panel Indicators .................................... 10

Fiber Compatibility Indications ....................... 10

Unit Mounting .......................................... 11

viiFOX 3G HD-SDI • Contents

FOX 3G HD-SDI • Contents viii

Introduction

WARNING: The FOX 3G HD-SDI outputs continuous invisible light (Class 1 rated),

which may be harmful to the eyes; use with caution.

Do not look into the rear panel fiber optic cable connectors or into the fiber optic
cables themselves.

Plug the attached dust caps into the optical transceivers when the fiber optic cable is
unplugged.

AVERTISSEMENT :

(conforme à la classe1) qui peut être dangereux pour les yeux, à utiliser avec
précaution.

Ne regardez pas dans les connecteurs de câble fibre optique sur le panneau arrière
ou dans les câbles fibre optique eux-mêmes.

Branchez les protections contre la poussière dans l’ensemble émetteur/récepteur
lorsque le câble fibre optique est débranché.

This section introduces this manual and the FOX 3G HD-SDI transceivers.

• About this Manual

• About the FOX 3G HD-SDI

• Features

Le FOX 3G HD-SDI émet une lumière invisible en continu

FOX 3G HD-SDI • Introduction 1

About this Manual

oadcast

Ext
FO

Fi
T

Video Editor

This manual contains information about the following Extron FOX fiber optic transceivers:

FOX 3G HD-SDI SM — A singlemode, very long distance (up to 30 km [18.75 miles])
transceiver. See figure 1.

FOX 3G HD-SDI P SM — A singlemode, very long distance (up to 30 km [18.75 miles])
transceiver that is pathologically compliant

FOX 3G HD-SDI MM — A multimode, long distance (up to 2 km [6,561 feet]) transceiver

X HD-SDI SM

ber Optic

ransceiver

ron

1 2

FOX HD-SDI

OPTICAL

BUFFERED OUTPUTS

MODE

ON

RxTx

1 2

POWER
12V

0.3A MAX
HD/SDI IN

HD-SDI Camera

Extron
FOX HD-SDI SM

Fiber Optic
Transceiver

OPERATE

STATUS

OVER RANGE

OPTION A

OPTION B

HD-SDI Broadcast
Monitor

Video Editor

Up to 30 km (18.75 miles)
on singlemode ber
SM Model

1 2

FOX HD-SDI

OPTICAL

BUFFERED OUTPUTS

MODE

ON

RxTx

1 2

POWER
12V

0.3A MAX
HD/SDI IN

OPTION B

HD-SDI Br
Monitor

OPERATE

STATUS

OVER RANGE

OPTION A

Figure 1. Typical FOX 3G HD-SDI Application

NOTE: The three products are physically and functionally identical, with the exception

of the effective range of transmission and the compliance. In this manual, the term
“FOX 3G HD-SDI” refers to any of the products.

About the FOX 3G HD-SDI

The Extron FOX 3G HD-SDI product family consists of three models (P SM, SM, and MM)
of high performance digital (HD-SDI, SDI, or 3G-SDI) video fiber optic transceivers. The
transmitted signal can include any audio or unidirectional serial data that is embedded in the
input video.

NOTE: All transceivers in the system must be the same model (all singlemode, all

singlemode pathologically compliant, or all multimode).

Transceiver Configurations

The transceiver can be configured via its rear panel Mode DIP switches to operate in one of
three ways:

• Bidirectional transceiver

• Transmitter

• Receiver

NOTE: See item B, “Mode switches,” on page 7 to set the configuration.

FOX 3G HD-SDI • Introduction 2

Bidirectional transceiver

12

Configured as bidirectional transceiver

Configured as bidirectional transceiver

NOTES:

• In this manual, the term “transceiver” refers to any FOX 3G HD-SDI; the term

“bidirectional transceiver” refers to a FOX 3G HD-SDI configured as described in
this section.

• Although the description below does allow connection of a FOX 3G HD-SDI

configured as transmitter or receiver, the typical configuration is as shown: two
bidirectional transceivers.

A FOX 3G HD-SDI that is configured as a bidirectional transceiver (see figure 2) inputs
digital video on its SDI/HD-SDI Input BNC. The transceiver converts the video input to a

proprietary signal and transmits the video over a fiber link to another FOX 3G HD-SDI that is
configured as either a bidirectional transceiver or a receiver.

HD-SDI

In From

Source A

POWER

12V

0.3A MAX

HD/SDI IN

FOX 3G HD-SDI

MODE

FOX HDSDI

OPTICAL

RxTx

HD-SDI
Out From
Source B

Out From
Source B

12

BUFFERED OUTPUTS

HD-SDI

FOX 3G HD-SDI

POWER

12V

0.3A MAX

HD-SDI

In From

Source B

HD/SDI IN

MODE

FOX HDSDI

OPTICAL

RxTx

HD-SDI
Out From
Source A

BUFFERED OUTPUTS

HD-SDI
Out From
Source A

Figure 2. Bidirectional Transceiver Connections

A bidirectional transceiver can also simultaneously receive a proprietary signal from another
transceiver (in any configuration) on its Optical Rx port, convert the proprietary signal back
to the original format digital video, and output the video on its own two Buffered Outputs
BNC connectors.

FOX 3G HD-SDI • Introduction 3

Transmitter and receiver

Configured as transmitter

Configured as receiver

FOX HD-SDI(s)

NOTE: Although the description below does allow connection of a FOX 3G HD-SDI

configured as a bidirectional transceiver, the typical configuration is as shown: a
transmitter and one or more receivers.

A FOX 3G HD-SDI that is configured as a transmitter (see figure 3) inputs digital video
on its HD/SDI Input BNC. The transmitter converts the video input to a proprietary signal
and transmits the video over a fiber link to a FOX 3G HD-SDI that is configured as either a
receiver or a bidirectional transceiver. The transmitter also simultaneously outputs the digital
video on its two Buffered Outputs BNCs.

Configured as receiver(s)

POWER

12V

0.3A MAX

HD-SDI

In From

Source A

FOX HDSDI

MODE

HD/SDI IN

OPTICAL

HD-SDI
Out From
Source A

RxTx

HD-SDI
Out From
Source A

12

BUFFERED OUTPUTS

Transmitted HD-SDI

POWER

12V

0.3A MAX

HD/SDI IN

from source A

MODE

FOX HDSDI

OPTICAL

RxTx

HD-SDI
Out From
Source A

1 2

BUFFERED OUTPUTS

Features

FOX 3G HD-SDI

FOX 3G HD-SDI

Figure 3. Transmitter-to-Receiver Connections

A FOX 3G HD-SDI that is configured as a receiver receives a proprietary signal on its
Rx fiber optic port. The receiver converts the proprietary signal back to original HD-SDI,
SDI, or 3G-SDI video and outputs the video on only one of its own Buffered Output BNC
connectors, Output 2.

The receiver converts the second digital video signal that it created from the optical input
back into a proprietary signal and outputs it on the Optical Tx port over a fiber link to
another FOX 3G HD-SDI that is configured as a receiver or as a bidirectional transceiver.

NOTE: Up to 10 receivers can be daisy-chained in this manner.

• Fiber optic characteristics — The FOX 3G HD-SDI sends and receives digital

optical signals via fiber optic small form factor pluggable (SFP) modules with LC-type
connectors.

• Extends HD-SDI, SDI, and 3G-SDI signals very long distances over a single fiber

— The FOX 3G HD-SDI supports multi-rate SDI at rates up to 2.97 Gbps, and complies
with SMPTE 259M-C, 292M, 424M, and ITU digital video standards.

• (FOX 3G HD-SDI P SM only) Immunity to SDI and HD-SDI pathological signal

patterns — The FOX 3G HD-SDI P SM model adds immunity to pathological signals,
including test patterns defined by SMPTE RP 178 and SMPTE RP 198 for SD-SDI,
HD-SDI and 3G-SDI

• Video input — When it is configured as a transmitter, the FOX 3G HD-SDI inputs digital

video on a BNC connector.

• HD-SDI loop-through — The transceiver has two Buffered SDI/HD-SDI BNC

connectors that allows connection of a local monitor when the transceiver is configured
as a transmitter.

FOX 3G HD-SDI • Introduction 4

• Video output — The transceiver outputs digital video on one or two Buffered

SDI/HD-SDI BNC connectors when it is configured as a bidirectional transceiver or a
receiver.

• Dual buffered outputs — When the FOX 3G HD-SDI is configured as a transmitter,

the SDI/HD-SDI BNC output connectors can be used for previewing the video on a
local monitor.

• Input equalization and reclocking on buffered outputs — The FOX 3G HD-SDI

automatically equalizes incoming multi-rate SDI signals, and reshapes and restores
signals on its buffered outputs.

• Daisy chain capability — Up to 3 transceivers can be daisy chained to send the video

to multiple locations when one of more units are configured as receivers.

• Real-time status LED indicators for troubleshooting and monitoring

• 1-inch high, quarter rack width, metal enclosures — With low profile enclosures,

the transceiver can be discreetly installed in various locations, such as behind a plasma
or LCD flat-panel display.

• Rack mountable — The unit is rack mountable in any conventional 19-inch wide rack,

using any of a variety of Extron rack shelves.

• Power — The 100 VAC to 240 VAC external power supply provides worldwide power

compatibility.

FOX 3G HD-SDI • Introduction 5

Installation and

12

CC DDEE BBAA

Operation

This sections details the installation of the FOX 3G HD-SDI, including:

• Installation Overview

• Connections and Settings

• Operation

Installation Overview

Follow these steps to install and set up an Extron FOX 3G HD-SDI for operation:

ATTENTION:

• Installation and service must be performed by authorized personnel only.

• L’installation et l’entretien doivent être effectués par le personnel autorisé

uniquement

1. Turn off all of the equipment. Ensure that the video sources and the output display are

all turned off and disconnected from the power source.

2. Mount the transceivers. See Mounting the Transceiver on page 11.

3. Connect the cables and configure the transceivers. See “Connections and Settings.”

4. Plug in the power supplies, then turn on the display devices and the input devices.

Connections and Settings

All connectors are on the rear panel (figure 4).

POWER

12V

0.3A MAX

HD/SDI IN

Figure 4. FOX 3G HD-SDI Transceiver Connectors

HD-SDI Input BNC (see page 7)

A

Mode switch (see page 7)

B

Fiber optic connectors (see page 7)

C

MODE

12

FOX HDSDI

OPTICAL

RxTx

BUFFERED OUTPUTS

FOX 3G HD-SDI • Installation and Operation 6

Buffered Outputs BNC (see page 8)

D

Power connector (see page 8)

E

HD-SDI Input connector (see figure 4 on the previous page) — If the

MODE

OPTICAL

RxTx

A

FOX 3G HD-SDI is configured as either a bidirectional transceiver or as a
transmitter, connect an HD-SDI, SDI, or 3G-SDI video input to this BNC connector.

Mode switches (see figure 4) — Set these DIP switches to the positions shown in the

B

table below to select the transceiver configuration. See Transceiver Configurations
on page 2 for more information.

SW2 Mode

SW1

Down

Down Bidirectional transceiver (default position)

UpDown

Transmitter with local monitor outputs

Up

Down

12

Fiber optic connectors (see figure 4) —

C

Receiver with daisy chaining

UpUp

Spare (functions as receiver with daisy chaining)

WARNING: The FOX 3G HD-SDI outputs continuous invisible light (Class 1 rated),

which may be harmful to the eyes; use with caution.

Do not look into the rear panel fiber optic cable connectors or into the fiber optic
cables themselves.

Plug the attached dust caps into the optical transceivers when the fiber optic
cable is unplugged.

AVERTISSEMENT :

Le FOX 3G HD-SDI émet une lumière invisible en continu
(conforme à la classe1) qui peut être dangereux pour les yeux, à utiliser avec
précaution.

Ne regardez pas dans les connecteurs de câble fibre optique sur le panneau
arrière ou dans les câbles fibre optique eux-mêmes.

Branchez les protections contre la poussière dans l’ensemble émetteur/récepteur
lorsque le câble fibre optique est débranché.

NOTE: Ensure that you use the proper fiber cable for your transceivers. Typically,

singlemode fiber cable has a yellow jacket and multimode fiber cable has an
orange or aqua jacket. Also, see Fiber Compatibility Indications on page 10 to
determine the compatibility of the transceiver.

Tx — In any FOX 3G HD-SDI configuration, for all one-way HD-SDI, SDI,
or 3G-SDI transmission, connect a fiber optic cable to the Optical Tx LC
connector.

RxTx

Connect the free end of this fiber optic cable to the Optical Rx LC connector
on another FOX 3G HD-SDI transceiver that is configured as either a
bidirectional transceiver or a receiver.

Rx — If the FOX 3G HD-SDI is configured as a bidirectional transceiver
or as a receiver, for one-way communications from the transmitting unit,

connect a fiber optic cable to the Optical Rx LC connector. Connect the free
end as detailed below:

In a 2-transceiver system, connect the free end of this fiber optic cable to
the Optical Tx LC connector on the transmitting FOX 3G HD-SDI, which is

OPTICAL

configured as a transmitter.

In a daisy-chained system, connect the free end of this fiber optic cable
to the Optical Tx LC connector on the previous FOX 3G HD-SDI in the daisy
chain.

FOX 3G HD-SDI • Installation and Operation 7

Buffered Outputs connectors (see figure 4 on page 6) — In any FOX 3G HD-SDI

Connector

Smooth

D

configuration, connect a digital display to these BNC connectors. See Transceiver
Configurations for more details.

If the FOX 3G HD-SDI is configured as a bidirectional transceiver, the video
is output on both connectors 1 and 2 and is the video signal sent from the other
transceiver.

If the FOX 3G HD-SDI is configured as a receiver, the video is output on connector
2 only and is the video sent by the transmitting unit.

If the FOX 3G HD-SDI is configured as a transmitter, the video is output on both
connectors 1 and 2 and is looped through from the HD/SDI Input connector, item A
on the previous page, on the same transceiver.

Power connector (see figure 4) — Plug the included external 12 VDC power supply

E

into this 2-pole captive screw connector. Figure 5 shows how to wire the power
connector. Use the supplied tie-wrap to strap the power cord to the extended tail of the
connector.

Ridges

AA

Power Supply

Output Cord

SECTION A–A

Tie Wrap

Captive Screw

3

5

Figure 5. Power Connector Wiring

CAUTION: The length of the exposed wires in the stripping process is important.

The ideal length is 3/16 inch (5 mm).

• Any longer and the exposed wires may touch, causing a short circuit between

them.

• Any shorter and the wires can be easily pulled out even if tightly fastened by

the captive screws.

ATTENTION :

La longueur des câbles exposés est importante lorsque l’on

entreprend de les dénuder. La longueur idéale est de 5mm (3/16inches).

• S’ils sont trop longs, les câbles exposés pourraient se toucher et provoquer

un court-circuit.

• S’ils sont trop courts, ils peuvent être tirés facilement, même s’ils sont

correctement serrés par les borniers à vis.

NOTE: Do not tin the power supply leads before installing them in the direct

insertion connector. Tinned wires are not as secure in the connectors and could

be pulled out.

FOX 3G HD-SDI • Installation and Operation 8

WARNING: The two power cord wires must be kept separate while the power

supply is plugged in. Remove power before wiring.

AVERTISSEMENT : Les deux cordons d’alimentation doivent rester séparés

tant que l’alimentation est branchée. Coupez l’alimentation avant de faire les
raccordements.

CAUTION:

• If not provided with a power supply, this product is intended to be supplied

by a power source marked “Class 2” or “LPS” and rated 12V DC, 0.5 A
minimum. Always use a power supply supplied by or specified by Extron. Use
of an unauthorized power supply voids all regulatory compliance certification
and may cause damage to the supply and the end product.

• Unless otherwise stated, the AC/DC adapters are not suitable for use in

air handling spaces or in wall cavities. The installation must always be
in accordance with the applicable provisions of National Electrical Code
ANSI/NFPA 70, article 725 and the Canadian Electrical Code part 1,
section 16. The power supply shall not be permanently fixed to a building
structure or similar structure.

• Power supply voltage polarity is critical. Incorrect voltage polarity can damage

the power supply and the unit. The ridges on the side of the cord (figure 5 on
the previous page) identify the power cord negative lead.

ATTENTION :

• Si le produit n’est pas fourni avec une source d’alimentation, il doit être

alimenté par une source d’alimentation certifiée UL de classe 2 ou LPS, avec
une tension nominale 12 Vcc, 0.5 A minimum. Utilisez toujours une source
d’alimentation fournie ou recommandée par Extron. L’utilisation d’une source
d’alimentation non autorisée annule toute conformité réglementaire et peut
endommager la source d’alimentation ainsi que le produit final.

• Sauf mention contraire, les adaptateurs CA/CC ne conviennent pas à une

utilisation dans les espaces d’aération ou dans les cavités murales. Cette
installation doit toujours être conforme aux dispositions applicables du Code
américain de l’électricité (National Electrical Code) ANSI/NFPA 70, article 725,
et du Code canadien de l’électricité, partie1, section16. La source
d’alimentation ne devra pas être fixée de façon permanente à la structure de
bâtiment ou à d’autres structures similaires.

• La polarité de la source d’alimentation est primordiale. Une polarité incorrecte

pourrait endommager la source d’alimentation et l’unité. Repérez le pôle
négatif du cordon d’alimentation grâce aux stries sur le côté du cordon
(illustration 5).

FOX 3G HD-SDI • Installation and Operation 9

Operation

Front Panel Indicators

After the transmitting and receiving units and all of their connected devices are powered up,
the system is fully operational. If any problems are encountered, ensure all traditional and
fiber cables are routed and connected properly.

All indicators are on the front panel (figure 6).

270

Mbps

Gbps

Gbps

UNKNOWN

FOX HDSDI

RATE

2.97

1.485

Figure 6. FOX 3G HD-SDI transceiver indicators

HD-SDI Input connector — When lit, this light emitting diode (LED) indicates that the

A

FOX 3G HD-SDI transceiver is receiving power.

Mode switches — These LEDs light to indicate the detected input video rate, either

B

on the HD/SDI input BNC (if configured as a transmitter) or on the Optical Rx connector
(if configured as a receiver or bidirectional transceiver). The recognized rates are
270 Mbps, 1.485 Gbps, or 2.97 Gbps.

When the Rate Unknown LED lights, this indicates that an input is detected, either on
the HD/SDI input BNC (if configured as a transmitter) or on the Optical Rx connector
(if configured as a receiver or bidirectional transceiver), but that the FOX 3G HD-SDI
does not recognize the rate.

NOTES:

• All four Rate LEDs blink repeatedly if a fiber optic connector module on the

rear of the unit is unseated.

• The FOX 3G HD-SDI equalizes and distributes the input whether it recognizes

the rate or not.

Fiber Compatibility Indications

You must use the proper fiber cable for your transceivers. Each transceiver indicates its fiber
compatibility, singlemode or multimode, at power-up by blinking the four Rate indicators.

Multimode — The Rate LEDs blink once.

Singlemode — The Rate LEDs blink twice.

NOTES:

• To determine the fiber cable type, observe the cable jacket. Typically, singlemode

fiber cable has a yellow jacket and multimode fiber cable has an orange or aqua
jacket.

• All transceivers in the system must be the same model (all singlemode or all

multimode). Mixed transmission mode units will not work together.

FOX 3G HD-SDI • Installation and Operation 10

Unit Mounting

Mounting the Transceiver

ATTENTION:

• Installation and service must be performed by authorized personnel only.

• L’installation et l’entretien doivent être effectués par le personnel autorisé

uniquement.

The 1-inch high, quarter rack width FOX 3G HD-SDI can be placed on a tabletop. It can
also be mounted on any of mounted in any of the following ways:

• On a rack shelf • Through a desk or tabletop

• Under a desk or tabletop • On a projector bracket

Tabletop Use

Affix the included rubber feet to the bottom of the unit and place it in any convenient location.

Mounting Kit

Mount the unit using any compatible rack, furniture, or projector mounting kit, listed on the
Extron website (www.extron.com), in accordance with the directions included with the kit.
For rack shelf mounting, also see “UL Rack-Mounting Guidelines.”.

UL Rack-Mounting Guidelines

The following Underwriters Laboratories (UL) guidelines pertain to the installation of the
FOX 3G HD-SDI into a rack.

• Elevated operating ambient — If installed in a closed or multi-unit rack assembly,

the operating ambient temperature of the rack environment may be greater than room
ambient. Therefore, consider installing the equipment in an environment compatible with
the +122 °F (+50 °C) maximum ambient temperature (Tma) specified by Extron.

• Reduced air flow — Installation of the equipment in a rack should be such that the

amount of air flow required for safe operation of the equipment is not compromised.

• Mechanical loading — Mounting of the equipment in the rack should be such that a

hazardous condition is not achieved due to uneven mechanical loading.

• Circuit overloading — Consideration should be given to the connection of the

equipment to the supply circuit and the effect that overloading of the circuits might have
on overcurrent protection and supply wiring. Appropriate consideration of equipment
nameplate ratings should be used when addressing this concern.

• Reliable earthing (grounding) — Reliable earthing of rack-mounted equipment

should be maintained. Particular attention should be given to supply connections other
than direct connections to the branch circuit (such as the use of power strips).

FOX 3G HD-SDI • Unit Mounting 11

Extron Warranty

Extron Electronics warrants this product against defects in materials and workmanship for a period of three years
from the date of purchase. In the event of malfunction during the warranty period attributable directly to faulty
workmanship and/or materials, Extron Electronics will, at its option, repair or replace said products or components,
to whatever extent it shall deem necessary to restore said product to proper operating condition, provided that it is
returned within the warranty period, with proof of purchase and description of malfunction to:

USA, Canada, South America,
and Central America:
Extron Electronics
1230 South Lewis Street
Anaheim, CA 92805

Japan:
Extron Electronics, Japan
Kyodo Building, 16 Ichibancho
Chiyoda-ku, Tokyo 102-0082
Japan

U.S.A.

Europe and Africa:

Extron Europe
Hanzeboulevard 10
3825 PH Amersfoort
The Netherlands

China:

Extron China
686 Ronghua Road
Songjiang District
Shanghai 201611
China

Asia:

Extron Asia Pte Ltd
135 Joo Seng Road, #04-01
PM Industrial Bldg.
Singapore 368363

Middle East:

Extron Middle East
Dubai Airport Free Zone
F13, PO Box 293666
United Arab Emirates, Dubai

Singapore

This Limited Warranty does not apply if the fault has been caused by misuse, improper handling care, electrical
or mechanical abuse, abnormal operating conditions, or if modifications were made to the product that were not
authorized by Extron.

NOTE: If a product is defective, please call Extron and ask for an Application Engineer to receive an RA (Return

Authorization) number. This will begin the repair process.

USA: 714.491.1500 or 800.633.9876 Europe: 31.33.453.4040
Asia: 65.6383.4400 Japan: 81.3.3511.7655

Units must be returned insured, with shipping charges prepaid. If not insured, you assume the risk of loss or damage
during shipment. Returned units must include the serial number and a description of the problem, as well as the
name of the person to contact in case there are any questions.

Extron Electronics makes no further warranties either expressed or implied with respect to the product and its quality,
performance, merchantability, or fitness for any particular use. In no event will Extron Electronics be liable for direct,
indirect, or consequential damages resulting from any defect in this product even if Extron Electronics has been
advised of such damage.

Please note that laws vary from state to state and country to country, and that some provisions of this warranty may
not apply to you.

Extron Headquarters

+1.800.633.9876 (Inside USA/Canada Only)

Extron USA - West Extron USA - East
+1.714.491.1500 +1.919.850.1000
+1.714.491.1517 FAX [phone] FAX

Extron Europe

+800.3987.6673
(Inside Europe Only)

+31.33.453.4040
+31.33.453.4050 FAX

© 2017 Extron Electronics All rights reserved. www.extron.com

Extron Asia

+65.6383.4400
+65.6383.4664 FAX

Extron Japan

+81.3.3511.7655
+81.3.3511.7656 FAX

Extron China

+86.21.3760.1568
+86.21.3760.1566 FAX

Extron Middle East

+971.4.299.1800
+971.4.299.1880 FAX

Extron Australia

+61.8.8113.6800
+61.8.8351.2511 FAX

Extron India

1800.3070.3777
(Inside India Only)

+91.80.3055.3777
+91.80.3055.3737 FAX