Extron Electronics FCMP 44 User Manual
FCMP 44 • Installation Guide
1½" NTP
IMPORTANT SAFETY INSTRUCTIONS
Read all instructions before starting installation.
When using this accessory, basic precautions should always be followed, including the following:
WARNING: Risk of Personal Injury. Maximum setup load for the FCMP 44 is 200 lbs (91.6 kg). The structural
ceiling must be capable of supporting 4 times the weight of the final setup.
SAVE THESE INSTRUCTIONS
NOTE: Refer to local building standards and codes to verify that the installation will meet the regulatory
requirements. Observe all local and national building and safety codes, UL requirements, and ADA
accessibility guidelines.
The FCMP 44 (Flat Ceiling Mount Plate) is a simple and
easily installed mounting solution for hanging a projector in
installations where a short extension pole is used or where larger
mounting plates cannot be installed. The FCMP 44 can support a
projector setup weighing up to 200 lbs (91.6 kg), and is suitable
for installation on wooden joists. It has an integral 1½"
National Pipe Thread pipe adapter, allowing the attachment of a
suitable projector pole, such as one of the Extron PMP
(Projector Mounting Pole) series. The FCMP 44 is a complementary
mounting accessory for use with the Extron UPB 25
(Universal Projector Mount Bracket).
The features of the FCMP 44 are shown in figure 1. Included in the kit are:
Flat Ceiling Mounting Plate, (1), and Hex Wrench, 3/32", (1).
Checking the Mounting Location
PRELIMINARY
Before starting the installation, it is important that these steps are followed:
• Check that the ceiling plate is suitable for the angle of the ceiling where the projector is to be installed.
• The installation must be done by a skilled technician
Set Screw
Mounting
Holes
Pipe Adapter
Figure 1. FCMP 44 Features
1
FCMP 44 • Installation Guide, cont'd
Extron
all dimensions in inches (millimeters)
Installation
To install the FCMP 44 on a flat ceiling
FCMP 44
Flat Ceiling Mounting
Plate
1. Locate a suitable wooden joist at the location chosen for the
installation. Mark the position of the four corner mounting
holes (see figure 1). Each hole should be in the center of a
joist (minimum size 2 inch by 4 inch). If the plate does not
span two joists, build up a suitable support, using 2 by 4 inch
minimum sized joists, ensuring each hole falls in the center
of a joist.
Extron
PMP
Projector Mount
Pole (optional)
2. Drill pilot holes perpendicular to the joist. The pilot holes
should be 70% of shank diameter and the full depth of the
lag bolts to be used (1/4 inch diameter by 4 inch lag bolts are
recommended).
3. Using fasteners suitable for the mounting surface (not
Projector
supplied, see above for recommended type), firmly secure
the FCMP 44 to the joists. A minimum of four bolts, with
washers, should be used.
4. Back out the set screws, and then screw a projector mounting
Figure 4. Typical Application of FCMP 44
pole (with an NPT 1.5 inch thread, such as an Extron PMP) of
suitable length into the mounting plate. A minimum of three
turns is needed to safely secure the pole.
Be careful not to cross thread the pole into the mounting plate.
5. Secure the pole in position by tightening the set screws down.
6. Follow the instructions supplied with the projector mounting bracket to hang the bracket.
Extron
UPB 25
Universal Projector
Mounting Bracket (optional)
Security Lock
Specications
Mount type .................................. Pole Mount
Material ........................................ Metal
PRELIMINARY
Plate dimensions .......................... Various (see image)
Shipping weight .......................... ~ 2 lbs (1 kg)
Maximum capacity ....................... 200 lbs (91 kg)
Regulatory compliance
Safety ..................................... CE, c-UL, UL for use with UL Listed
mount and projector;
OSHPD anchorage pre-approval
Vibration ...................................... ISTA 1A in carton (International
Safe Transit Association)
Warranty ...................................... 3 years parts and labor
2.00 [50.8]
(1 1/2"-11.5 NPT)
4.00 [101.6]
2X .66 [16.6]
4X .44 [11.2]
2.220
[56.39]
(CUTOUT)
2X 2.690 [68.3]
4X .75 [19.0]
2.00 [50.8]
Figure 3. FCMP 44 Dimensions
2X .50 [12.7]
4.00 [101.6]
2X 3.000 [76.2]
Extron Headquarters
+1.800.633.9876 (Inside USA/Canada Only)
Extron Europe
+31.33.453.4040
© 2012 Extron Electronics — All rights reserved. All trademarks mentioned are the property of their respective owners. www.extron.com
2
Extron Asia
+65.6383.4400
Extron Japan
+81.3.3511.7655
Extron China
+86.21.3760.1568)
Extron Middle East
+971.4.2991800
Extron Korea
+82.2.3444.1571
Extron India
+91.80.3055.3777
68-1248-01
Rev B
08 12
Loading...