Extron Electronics FCMP 1010 User Manual
FCMP 1010 • Installation Guide
IMPORTANT SAFETY INSTRUCTIONS
Read all instructions before starting installation.
When using this accessory, basic precautions should always be followed, including the following:
WARNING: Risk of Personal Injury. Maximum setup load for the FCMP 1010 is 200 lbs (91.6 kg). The
structural ceiling must be capable of supporting 4 times the weight of the final setup.
SAVE THESE INSTRUCTIONS
NOTE: Refer to local building standards and codes to verify that the installation will meet the regulatory
requirements. Observe all local and national building and safety codes, UL requirements, and ADA
accessibility guidelines.
FCMP 1010 Flat Ceiling Mounting Plate
The FCMP 1010 is a simple and easily installed mounting
solution for hanging a projector in installations where a long
extension pole is used. The FCMP 1010 is available in black, can
support a projector setup weighing up to 200 lbs (91.8 kg), and
is suitable for installation on wooden joists and metal beams.
It has an integral 1½" National Pipe Thread pipe adapter,
allowing the attachment of a suitable projector pole, such as
one of the Extron PMP (Projector Mounting Pole) series (See
page 2 for list). The FCMP 1010 is a complementary mounting
accessory for use with the Extron UPB 25 (Universal Projector
Mount Bracket).
The features of the FCMP 1010 are shown in figure 1. Included
in the kit are:
PRELIMINARY
Flat Ceiling Mounting Plate, (1), and Hex Wrench, 3/32", (1).
Checking the Mounting Location
Before starting the installation, it is important that these steps are followed:
• Check that the ceiling plate is suitable for the angle of the ceiling where the projector is to be installed.
• The installation must be done by a skilled technician
Mounting
Holes
1½" NTP
Set Screws (2)
Figure 1 — FCMP 1010 Features
Pipe adapter
Installation
To install the FCMP 1010 on a flat ceiling
1. Locate a suitable wooden joist at the location chosen for the installation. Mark the position of the four corner
mounting holes, or a minimum of one hole per side (see figure 1) in the center of a joist (minimum size 2 inch
by 4 inch).
2. Drill pilot holes perpendicular to the joist. The pilot holes should be 70% of shank diameter and the full depth
of the lag bolts to be used (1/4 inch diameter by 4 inch lag bolts are recommended).
3. Using fasteners suitable for the mounting surface (not supplied, see above for recommended type), firmly
secure the FCMP 1010 to the joists. A minimum of four bolts, with washers, should be used.
4. Back out the set screws, and then screw a projector mounting pole (with an NPT 1.5 inch thread, such as an
Extron PMP) of suitable length into the mounting plate. A minimum of three turns is needed to safely secure
the pole. Be careful not to cross thread the pole into the mounting plate.
5. Secure the pole in position by tightening the set screws down.
6. Follow the instructions supplied with the projector mounting bracket to hang the bracket.
1
FCMP 1010 • Installation Guide, cont'd
Extron
Specications
Mount type .................................. Pole Mount
Material ........................................ Metal
Plate dimensions .......................... Various (see image below)
Shipping weight .......................... ~ 3 lbs (1 kg)
Maximum capacity ....................... 200 lbs (92 kg)
Regulatory compliance
Safety ..................................... CE, c-UL, UL for use with UL
Listed mount and projector;
OSHPD anchorage pre-approval
Vibration ...................................... ISTA 1A in carton (International
Safe Transit Association)
Warranty ...................................... 3 years parts and labor
FCMP 1010
Flat Ceiling Mounting
Plate
Extron
Extron
PMP
Projector Mount
Pole (optional)
Projector
UPB 25
Universal Projector
Mounting Bracket (optional)
Figure 3. Typical Application of FCMP 1010
Security
Lock
PRELIMINARY
4X Ø.34
[Ø8.73]
Ø2.20
[Ø55.88]
THRU
(CUTOUT)
8X .34 X .59
[8.73] X [15.08]
16X R
5.00
3X 4.50
[114.30]
[127.00]
2X 2.12
[53.88]
2X 2.12
[53.88]
Figure 2. FCMP 1010 Dimensions
3X 4.50
[114.30]
2X 2.12
[53.88]
2X 2.12
[53.88]
3X 4.50
[114.30]
3X 4.50
[114.30]
5.00
[127.00]
Extron Headquarters
+1.800.633.9876 (Inside USA/Canada Only)
Extron Europe
+31.33.453.4040
© 2012 Extron Electronics — All rights reserved. All trademarks mentioned are the property of their respective owners. www.extron.com
2
Extron Asia
+65.6383.4400
Extron Japan
+81.3.3511.7655
Extron China
+86.21.3760.1568)
Extron Middle East
+971.4.2991800
Extron Korea
+82.2.3444.1571
Extron India
+91.80.3055.3777
68-1356-01
Rev B
08 12
Loading...