Extron Electronics Extender Setup Guide

Setup Guide — Extender Series

To RGB
Video Equipment

Extender Series

9

-1

8

VD

C

wer

Gain

(S

w

itch

is on

th

e

lo

w

er circu

it b

oa

rd

.)

Maximum

Max. peaking

& gain

Medium

– Mid-lev

el

peaking & gain

Normal

Unity

gain

www.extron.com

33-612-02

Rev. C

02 05

L

Audio

R

Sleeve (s)

Left Tip

Left Ring

9-18 VDC

Power

Sleeve (s)

Left Tip

Right Tip

Left Ring

Right Ring

9-18 VDC

Power

Audio

Unbalanced Output

Left Tip

NO Ground Here

Sleeve(s)

Right Tip

NO Ground Here

Balanced Output

Sleeve(s)

Left Tip

Right Tip

Left Ring

Right Ring

L

Audio

R

L

Audio

R

Do not tin the wires!

CAUTION

For unbalanced audio, connect the
sleeve(s) to the ground contact.

DO NOT connect the sleeve(s) to

the negative (-) contacts.

Installation

Cable

Cable Clamp

Wall Stud

Screws or

Nails

W

Installation and service must be performed by

authorized personnel only. These products
must be used with UL approved, grounded
electrical boxes.

Step 1

Turn all of the equipment off and disconnect the power cords
from the power source.

Step 2

Select the installation location and install the electrical
wall box.

N

The Extron Extender AAP EX does not require

a wall box if it is installed into an Extron
HSA 400 Series or HSA 800 Series surface access
product.

Step 3

Attach the cables. See chapter 2 in the Extender Series User’s Manual.
For the Extender AAP EX, install the unit into the faceplate of an Extron
HSA 400 Series or HSA 800 Series surface access product before attaching the cables.

N

Horizontal sync = black.

Vertical sync = yellow.

(Continued on reverse side)

Setup Guide — Extender Series, cont’d

Extron USA - West

Headquarters

+800.633.9876

Inside USA / Canada Only

+1.714.491.1500
+1.714.491.1517 FAX

Extron USA - East

+800.633.9876

Inside USA / Canada Only

+1.919.863.1794
+1.919.863.1797 FAX

Extron Europe

+800.3987.6673

Inside Europe Only

+31.33.453.4040
+31.33.453.4050 FA X

Extron Asia

+800.7339.8766

Inside Asia Only

+65.6383.4400
+65.6383.4664 FAX

Extron Japan

+81.3.3511.7655
+81.3.3511.7656 FAX

Extron China

+400.883.1568

Inside China Only

+86.21.3760.1568
+86.21.3760.1566 FAX

Extron Middle East

+971.4.2991800
+971.4.2991880 FAX

Cable
Clamp

Screws or Nails

Wall Stud

#4-40 Nut w/ Captive
Washer

Extron

Extender AAP

AAP 102

AAP 102

EXTENDER

COMPUTER IN

AUDIO IN

Extron
Extender AKM MAAP

Line Driver

EXTENDER AKM MAAP

COMPUTER IN

AUDIO IN

#4 - 40 Screws

Maximum

Max. peaking

and gain

Medium – Mid-level

peaking and gain

Normal

Unity

gain

Maximum

Max. peaking

and gain

Medium – Mid-level

peaking and gain

Normal

Unity

gain

Circuit

board

Faceplate

Maximum –

Max. peaking

and gain

Medium –

Mid-level

peaking

and gain

Normal –

Unity gain

Extender D

(viewed

from front)

Extender WM

Extender WM AAP

(viewed from side)

Extender MK, AKM,

AUS, AAP Models

(viewed from rear)

Step 4

Mount all AAPs into faceplates with AAP openings.
Mount Extender AAP models into wall plates or faceplates.

Step 5

Connect power and turn the equipment on.

Step 6

Test the system and set the gain switch. Ensure that all devices
receive power. Check and adjust cabling and gain as needed.

Step 7

Disconnect power from all the devices.

Step 8

Mount the line driver into the electrical box or the body of the HSA. See the

Extender AKM MAAP Installation Guide, or the appropriate HSA Series user’s manual, if needed.

Step 9

For the Extender D, install the Decora© faceplate.

Step 10

Restore power to the devices.

© 2009 Extron Electronics. All rights reserved.

68-552-50

Rev. A

02 09