Extron Electronics EWB 700 User Manual

EWB 700 User Guide

The Extron® EWB 700 is an optional accessory for mounting the TLP 700MV

Conduit

Cables

touchpanel onto the surface of various wall types (such as drywall, wood, or masonry) where it is not possible to embed the touchpanel in the wall. The EWB 700 has knockouts that accept raceways or conduit for running cables over the surface of the wall to the touchpanel.

The following items are required for installation, but are not supplied:

• Extron TLP 700MV (includes

Extron TR 700M Trim Ring)

• Four screws (Extron recommends a

minimum length of 1 inch, if possible)

• Power drill

• Drill bit that is appropriate for wall type

Extron EWB 700

Wall Box

Extron TR 700M

Trim Ring

Extron TLP 700MV

Faceplate

• Conduit or surface raceway to carry cables

• Screwdriver

• Level

Fastener Suggestions for Different Wall Types

Choose a type of screw or bolt that is appropriate for the wall (see table below). The mounting holes in the back of the EWB 700 accommodate screws up to ¼ inch in diameter.

Wall Type Fasteners Min. Size

Fastener

Drywall Toggle bolts 3/16 inch 4 1/2 inch Min. 3/8 inch

Wood (solid wall or stud)

Masonry Masonry

Wood screws #10 screw

with a washer

1/4 inch 4 3/16 inch

screws

Quantity Drill Bit

Size

4 1/16 inch

wood bit

masonry bit

Notes

wall thickness

Min. 3/8 inch wall thickness

Do not mount to masonry joints

Mounting the EWB 700

1. If mounting to standard wood wall studs, locate

the center of the studs.

2. Place the EWB 700 against the wall in a suitable

location. Use a level to ensure the box is horizontal and mark the position of the four holes.

3. If required, drill four holes into the wall.

4. Insert four screws (see the table above) and attach

the EWB 700 to the wall.

Mounting Screws (4)

EWB 700 User Guide (cont’d)

5. Remove the required knockout and run

conduit or raceway to the EWB 700.

6. Pull the cables through the conduit,

the EWB 700 knockout, and the Extron TR 700M trim ring (provided with the Extron TLP 700MV).

7. Attach the trim ring to the EWB 700 using

four #6-32 screws (provided).

CAUTION: Do not overtighten the

screws. Use a manual screwdriver.

Installing the TLP 700MV

8. Remove the faceplate from the TouchLink

panel.

9. Attach the cables to the back of the

TLP 700MV. There are three sets of cables:

• One cable for the 12 VDC power input

• Two cables with BNC connectors for

video (optional)

• One network cable with a

RJ-45 connector for network connection

Trim Ring Screws (4)

Power Input

Video Input

Network Connection

10. Fold the locking arms

into their recesses on the side of the TLP 700MV and slide the unit into the wall box. Tighten the screws on the front of the unit to hold the unit in place. The locking arms rotate behind the EWB 700 and trim ring.

11. Conﬁgure the TLP 700MV

as described in the

TLP 700MV and TLP 700TV User Guide.

12. Snap the faceplate into

position (four clips on each side).

Extron USA - West Headquarters

+800.633.9876

Inside USA/Canada Only

+1.714.491.1500 +1.714.491.1517 FAX

Extron USA - East

+800.633.9876

Inside USA/Canada Only

+1.919.863.1794 +1.919.863.1797 FAX

Extron Europe

+800.3987.6673

Inside Europe Only

+31.33.453.4040 +31.33.453.4050 FAX

Extron Asia

+800.7339.8766

Inside Asia Only

+65.6383.4400 +65.6383.4664 FAX

Extron Japan

+81.3.3511.7655 +81.3.3511.7656 FAX

Extron China

+400.883.1568

Inside China Only

+86.21.3760.1568 +86.21.3760.1566 FAX

Locking Arm (6)

Extron Middle East

+971.4.2991800 +971.4.2991880 FAX

68-1932-01

07 10

Rev B