IMPORTANT:
specifications bef
Power Supply
)
POWER
ABCE GIH
DF
ore connecting the
EDID 101H 4K • Setup Guide
Go to www.extron.com for the complete
user guide, installation instructions, and
product to the power source.
This guide provides basic instructions for an experienced installer to install and operate the
EDID 101H 4K.
The Extron EDID 101H 4K is an EDID Emulator for HDMI signal sources. It features EDID Minder®, an Extron-exclusive technology
that provides automatic and continuous EDID - Extended Display Identication Data - management. EDID Minder ensures that
the source powers up properly and reliably outputs content. Pre-stored EDID information is communicated to the source based
on a user-selected resolution and refresh rate. Alternatively, the EDID 101H 4K can be congured to capture and store EDID
information from a connected display. The EDID 101H 4K is housed in a compact 1 inch high, quarter-rack width, 6-inch deep
enclosure for convenient, discreet installation. An energy-efcient external universal power supply is included.
Rear Panel Cabling
AB C
POWER
12V
0.3 A MAX
EDID 101H 4K
INPUT OUTPUT
Figure 1. EDID 101H 4K Rear Panel
Power Connector – Connect the included 12VDC power supply to this orange, two-pole, 3.5mm captive screw connector.
A
12V
0.3A MAX
Rear Panel
Power Receptacle
ATTENTION: Risk of property damage:
ATTENTION : Risque de dommages matériels :
• Do not connect any external power supplies until you
have read the Attention notications in the Power Supply
section of the user guide for that device.
• Ne branchez pas de sources d’alimentation externes
avant d’avoir lu les mises en garde dans la section «
Ground
+12 VDC
AC Power Cord
External
(12 VDC, 1 A
Power Supply » du guide utilisateur pour cet appareil.
Figure 2. External Power Supply Connection
HDMI Input – Connect an HDMI source to this female HDMI Type A connector.
B
HDMI Output – Connect a display or other output device to this female HDMI Type A connector.
c
Front Panel
CONFIG
Figure 3. EDID 101H 4K Front Panel
Power LED – Illuminates when power is supplied.
A
Config port – Mini USB connector for SIS configuration, monitoring, and firmware updates.
B
IN OUT
SIGNAL
HDCP
EDID
STORE
EDID 101H 4K
1
HDMI Input Signal LED (see figure 3) – This LED illuminates green when a signal is detected at the HDMI input.
C
Input HDCP LED – This LED illuminates green if the source requires HDCP and has been authenticated with the HDMI input.
D
HDMI Output LED – This LED illuminates green when a display or other output device is connected to the HDMI output.
E
Output HDCP LED – This LED illuminates green if the signal is encrypted and the HDMI output is authenticated with the
F
connected display.
EDID Store Status LED – One green LED illuminates when power is available and the rotary switch is in positions D, E, or
G
F. It blinks when reading and storing an EDID setting from a connected output device, returning to solid green when EDID
storing is complete.
LED
(G)
Rotary
Switch
Store Button (H)
Description
(I)
Off 0-C Non-functional EDID storing is not possible on the selected rotary switch position.
Solid D-F N/A EDID storing is possible on the selected rotary position.
Blinking D-F Button pressed and
released
After the Store button is pressed, the EDID is written to the user slot
selected by the rotary switch. When the EDID is stored, the LED turns
solid green.
EDID Store Button – One recessed push-button initiates both reading and storing an EDID from the connected display.
H
Press the Store button to read the EDID of the connected device and store it to a user slot selected by the rotary switch. Up
to three EDID files (switch positions D through F) can be stored.
EDID Selection Rotary Switch – One 16-position rotary switch allows the selection of a user stored or Extron factory EDID.
I
See the table below to determine the rotary switch position for the desired EDID. Position 8 is the default. Position C reads
the EDID of a connected display.
Switch
Position
Resolution Refresh
(Hz)
Audio Switch
Position
Resolution Refresh
(Hz)
Audio
0 1280x800 60 2-Ch 8 720p 60 2-Ch
1 1440x900 60 2-Ch 9 1080p 50 2-Ch
2 1600x900 60 2-Ch A 1080p 60 2-Ch
3 1680x1050 60 2-Ch B 4K/UHD 30 2-Ch
4 1920x1200 60 2-Ch C Output Automatically populated
with the connected
display EDID
5 2560x1440 60 2-Ch D User Slot 1
6 2560x1600 60 2-Ch E User Slot 2
7 720p 50 2-Ch F User Slot 3
Connect and Power the EDID 101H 4K
1. Set the rotary switch (see gure 3,
2. Connect an HDMI cable from the source to the EDID 101H 4K Input (see gure 1,
3. Connect an HDMI cable from the EDID 101H 4K Output (
4. Turn on the video display.
5. Connect the power supply to the EDID101H 4K (
6. Connect AC power to the power supply. The EDID 101H 4K power LED lights green.
7. Turn on the video source. The video source reads the EDID from the EDID101H 4K.
Extron Headquarters
+800.633.9876 Inside USA/Canada Only
Extron USA - West Extron USA East
+1.714.491.1500 +1.919.850.1000
+1.714.491.1517 FAX +1.919.850.1001 FAX
© 2016 Extron Electronics All rights reserved. All trademarks mentioned are the property of their respective owners. www.extron.com
2
Extron Europe
+800.3987.6673
Inside Europe Only
+31.33.453.4040
+31.33.453.4050 FAX
on page 1) for the desired resolution.
I
) to the display or distribution system.
C
).
A
Extron Asia
+65.6383.4400
+65.6383.4664 FAX
Extron Japan
+81.3.3511.7655
+81.3.3511.7656 FAX
Extron China
+86.21.3760.1568
+86.21.3760.1566 FAX
on page 1).
B
Extron Middle East
+971.4.299.1800
+971.4.299.1880 FAX
Extron Australia
+61.8.8351.2188
+61.8.8351.2511 FAX
Extron India
1800.3070.3777
(Inside India Only)
+91.80.3055.3777
+91.80.3055.3737
FAX
68-2784-50 Rev. A
04 16
Loading...