Extron electronic PMK 560 User Manual

IMPORTANT:

ews

Go to www.extron.com for the

PMK 560 • Installation Guide

complete system installation guide,

instructions, and specifications.

The Extron PMK 560 Pole Mount Kit, designed for use with the Extron PoleVault™ System, allows
for easy mounting of PoleVault products to a projector pole. It is used to mount the PoleVault system switcher the associated
power supply and an accessory device within an enclosure and below a suspended ceiling.

CAUTION: Maximum load for the PMK 560 is 15 lbs (6.8 kg).

Items included in the kit are:
Covers (2), Base plate (1), Mounting plate (1),
Tie wraps and pads (to secure power supply)
4-40 Screws (to mount devices) (3),Cover Screws (4)

NOTE: For full device installation, configuration,

menus, connector wiring, and operation details of
the PoleVault switcher, see the PoleVault System
Installation Guide, available at www.extron.com.

Installation

To install the PMK 560 in a PoleVault system:

1. Remove the four cover screws from the center of the PMK 560

(see gure 1). Slide the two halves apart and remove them from
the base plate.

NOTE: If the PoleVault switcher and its power supply

are already installed, go directly to step 4.

2. To mount the PoleVault switcher, place the mounting plate, with

the raised tabs upwards, on the top surface of the switcher and
pass the two supplied 4-40 x 3/16 inch screws into the top of the

switcher (see gure 2, b). Secure the mounting plate but do not
overtighten.

3. Attach the associated power supply to the base plate with the

supplied tie wraps and pads, by passing them through the
appropriate slots and around the power supply (see gure 2 c).

Tighten until snug.

4. Loosen the four pipe collar set screws (see gure 2 d), and slide

the base plate up the pipe until it is touching the suspended ceiling.

5. Level the base plate and secure it by fully tightening the set screws.

NOTE: At least three set screws must come in contact

with the pipe.

6. Hook the combined plate and switcher into the PMK 560 base plate

(see gure 2, e). Secure it to the base plate with two screws.

Mounting Plate

Base Plate

PMK Covers (2)

Figure 1. PMK 560

4

Attach PMK to the projector
pole pipe collar with the four
10-32 set screws.

5

Hook the combined mounting
plate and switcher into the
base plate and secure with
screws.

2

Attach Mounting plate
to the top of the
PoleVault switcher.

To open, remove 4 cover scr
and slide the covers away.

3

Attach
Power
Supply

Projector
Pole

INPUTS

POWER
12V
3A MAX

1/2

SIG

OUTPUT

LINK SIG LINK

3/4

AUDIO OUT

L

HDMI

PVT IN

PAGING

R

SENSOR

PVS 405SA IP

PVT IN

INPUT 5

L

+V

R

VOICELIFT

AUX

AMPLIFIED AUDIO OUT

DO NOT
GROUND
OR SHORT
SPEAKER
OUTPUTS

L R

OVER PVT

4/8
Ω

IR

REMOTE

RS-232

LAN 1

SG G

Tx

Rx

PVS 405D
Switcher

LAN 2 LAN 3

ATTENTION: Use only supplied screws to avoid

damaging the switcher.

Figure 2. Attach the mounting plate to the switcher

and secure both to the base plate.

PMK 560 • Installation Guide (Continued)

7. Route the signal cables so that they exit the pipe via the cable access slot (see gure 3).

WARNING: Do not thread any high voltage power cabling, such as power supply or projector power cords, through the

projector pipe. This violates National Electrical Code.

8. Attach the cables to the switcher and pull any excess cable back into the ceiling. Feed the output cables to the projector via

the cable access slot to the base of the pipe.

9. Continue installing the projector and other devices, following the directions of the relevant device manufacturer.

10. Slide the covers onto the base plate, passing the AC power cord out through the power cord slot between the covers (see

gure 3).

11. Lock the covers to the plate with the cover screws.

Refer to the PoleVault System Installation Guide, available at www.extron.com, to complete the installation and setup.

Power Cord Slot

PVS 305SA IP
Switcher

INPUTS

POWER
12V
3A MAX

1/2

SIG LINK SIG

OUTPUT

3/4

PVS 405D
Switcher

AUDIO OUT

LINK

L

HDMI

PVT IN

PAGING

R

SENSOR

PVS 405SA IP

PVT IN

INPUT 5

L

+V

R

VOICELIFT

AUX

AMPLIFIED AUDIO OUT

DO NOT
GROUND
OR SHORT
SPEAKER
OUTPUTS

L R

OVER PVT

4/8
Ω

IR

REMOTE

RS-232

LAN 1 LAN 2 LAN 3

S

G G

Tx

Rx

Cable Access Slot

Power Supply

Projector
Pole

Cable Slot
Cover

Figure 3. Attach the PMK to the pole, cable the PVS switcher and then re-attach the

two covers (inset shows the PVS 305SA IP installation location).

Power Supply

Extron Headquarters

+800.633.9876 (Inside USA/Canada Only)

Extron USA - West Extron USA - East

+1.714.491.1500 +1.919.850.1000

+1.714.491.1517 FAX [phone] FAX

© 2013 Extron Electronics All rights reserved. All trademarks mentioned are the property of their respective owners. www.extron.com

Extron Europe

+800.3987.6673

(Inside Europe Only)

+31.33.453.4040

+31.33.453.4050 FAX

Extron Asia

+65.6383.4400

+65.6383.4664 FAX

Extron Japan

+81.3.3511.7655

+81.3.3511.7656 FAX

Extron China

+86.21.3760.1568

+86.21.3760.1566 FAX

Extron Middle East

+971.4.299.1800

+971.4.299.1880 FAX

Extron Korea

+82.2.3444.1571

+82.2.3444.1575 FAX

Extron India

1800.3070.3777

(Inside India Only)

+91.80.3055.3777

+91.80.3055.3737 FAX

68-2385-01 Rev. A

08 13