Extron electronic P-2 DA2 MT User Manual

User’s Guide
P/2 DA2 MT
Distribution Amplifier
68-435-01 B
Printed in the USA
01 02
Installation and Operation
Description
Front Panel
Rear Panel
The P/2 DA2 MT Distribution Amplifier can be mounted using the included mounting brackets and screws. Audio input and output connectors and an external DC power supply are also features of the P/2 DA2 MT. See example application diagram below.
Stereo
P/2 DA2 MT
PC Audio Input
Output
B U
F F
E R
E D
LOCAL MONITOR
C O
M P
U T
E
R
ID P
IN 4
INPUT
I D
P I N
1 1
P
/
2
D
A
2
M
T
With Mounting Brackets
B U
F F E
R E
D
L O
C A
C
L
O
M
M
O
P
N
U
I
T
T
E
O
R
R
I D P
I N 4
I
N
I D
P
P
U
I N
T
1 1
P
/ 2
D
A 2
M
T
Mounted under a Desk
or
Mounted in a Table
L O
C A L
M O
N I T O
B U
R
F F E R
E D
I N
P U T
C
O M P U
T E R
I D
P
P I
/
N
2
4
D
A
I D
2
P I
N
M
1 1
T
or
PC Computer
Video MonitorProjector
The front panel consists of a 2-color LED indicator (amber indicates power On only, green indicates power On with video signal present), a 3.5 mm female audio input jack, a 15-pin female VGA input, a 15-pin female VGA buffered local monitor output, and 2 DIP switches that set the input termination.
COMPUTER
INPUT
BUFFERED
LOCAL MONITOR
ID PIN 4
ID PIN11
P/2 DA2 MT
The rear panel consists of a 9-volt power input jack, a Level/ Peaking DIP switch to control video level and peaking (data display device only), a 15-pin VGA output connector, and a 3.5 mm captive screw audio output connector.
POWER
9V DC
0.5A MAX.
SPARE
LEVEL/PEAKING
DATA DISPLAY
Easy Setup Procedure
These easy-to-follow steps describe the general setup of the P/2 DA2 MT. Refer to the previous application diagram.
1. If the P/2 DA2 MT is to be mounted using the mounting brackets, please refer to the previous section.
2. Power off the computer and its local monitor.
3. Connect the computer’s VGA output to the 15-pin female VGA input on the front panel of the P/2 DA2 MT.
4. If a local monitor is being used, connect the monitor to the 15­pin local monitor output on the front panel.
5. Set termination pins (see below).
6. If audio is being input, connect the audio source to the 3.5 mm audio input jack on the front panel. Refer to the audio connector diagrams on the last page.
7. Connect the output display device, such as a projector, VGA­compatible monitor, etc., to the 15-pin VGA data display connector on the rear panel of the P/2 DA2 MT.
8. Connect an audio device to the 3.5 mm captive screw audio output connector on the rear panel. Refer to the audio connector diagram on the following page.
9. Connect the 9-volt power plug of the included power supply into the power input jack on the rear panel.
Front Panel DIP Switch Settings
Set the two DIP switch pin positions (on/up or off/down):
Pin 4 Pin 11 Function
off off computer input pins 4 & 11 passed to
on on provide ID bit termination when no
on off provide correct MAC 13” ID bit
Rear Panel DIP Switch Settings
Set the Level/Peaking DIP switch On (up) to increase level and peaking of the data display, otherwise, set the switch Off (down).
Front Panel DIP Switch Settings
ID PIN 4
local monitor output connector
local monitor connected
termination
ID PIN11
Mounting Bracket
The included mounting brackets are attached to the P/2 DA2 MT using the 6 bracket screws, as shown on page 5. The unit may then be mounted under a desk or some other suitable location using the 4 wood screws (see mounting template). Optional brackets are also available for vertical mounting (see mounting template).
Operation
1. Power on the computer and monitor.
2. Power on the output display device.
3. Power on the P/2 DA2 MT. The LED will light amber when the power is on and will light green when the power is on and there is an input present.
P/2 DA2 MT • Installation and OperationP/2 DA2 MT • Installation and Operation
Installation and Operation, cont’d
B U F F E
R E D
L O C A
L M O N
I
T O R
C O M P
U T E R
P /
2 D A
2 M
T
I
N P U T
IN P U T
I D P I N 1 1
ID P IN 4
B
UFFERE
D
L
O
C
A
L M
O
NIT
O
R
CO
M
P
U
TE
R
ID PIN11
I
D
P
I
N
4
P
/
2
D
A
2
M
T
IN
PU
T
IN
P
U
T
p
Audio Connections
Warning!
___
No sleeve means NO CONNECTION. Wiring errors
Unbalanced output:
(high impedance)
Balanced output: (high
impedance or 600 ohms)
or plugging the audio connectors incorrectly may damage the audio output circuits.
Under Desk
Recommended pilot drill hole size
for supplied screws = 3/32” x 1/4” deep .
All dimensions are in inches
Thru desk mounting template
(Requires mounting kit P/N 70-077-02)
Thru Desk
= Bracket hole diameter - 4 places
P/2 DA2 MT • Installation and OperationP/2 DA2 MT • Installation and Operation
Installation and Operation, cont’d
Specifications
Video
Gain ................................................ (0.7V) unity, (0.8V) 15%
Bandwidth ..................................... 300 MHz (-3dB)
Video input
Number/signal type ................... 1 VGA-UXGA RGBHV, RGBS, RGsB,
RsGsBs
Connectors ................................... 1 15-pin HD female
Minimum/maximum level(s) .... Analog ....... 0.4V to 1.4V p-p with no
offset at unity gain
Impedance .................................... 75 ohms
Horizontal frequency .................. 15 kHz to 135 kHz
Vertical frequency ....................... 30 Hz to 170 Hz
Return loss .................................... -38.3dB @ 5 MHz
Maximum DC offset .................... 200mV
Video output
Number/signal type ................... 2 VGA-UXGA RGBHV, RGBS, RGsB,
RsGsBs
(1 for display, 1 for local monitor output)
Connectors ................................... 2 15-pin HD female
Minimum/maximum levels ....... 0.4V to 1.4V p-p
Impedance .................................... 75 ohms
Return loss .................................... -41dB @ 5 MHz
DC offset ....................................... ±5 mV maximum with input at 0 offset
Sync
Input type ..................................... RGBHV, RGBS, RGsB, RsGsBs
Output type .................................. RGBHV, RGBS, RGsB, RsGsBs
Input level ..................................... 3V to 5V p-p
Output level .................................. TTL ............. 5V p-p
Input impedance .......................... 75 ohms or 510 ohms (selectable)
Output impedance ....................... 75 ohms
Max. propagation delay .............. 18.8 nS
Max. rise/fall time ....................... 4 nS
Recommended pilot drill hole size for supplied screws = 3/32” x 1/4” deep .
Polarity .......................................... Positive or negative
Audio
Gain ................................................ Unbalanced 0dB, balanced +6dB
Frequency response .................... 20 Hz to 20 kHz, ±0.05dB
THD + Noise ................................. 0.03% @ 1 kHz at rated maximum output
drive
S/N ................................................ >90dB, balanced, at rated maximum
output drive (21dB)
Stereo channel separation .......... >80dB @ 1 kHz
P/2 DA2 MT • Installation and OperationP/2 DA2 MT • Installation and Operation
CMRR ............................................ >75dB @ 20 Hz to 20 kHz
Audio input
Number/signal type ................... 1 stereo, unbalanced
Connectors ................................... 1 3.5 mm female stereo jack, 2-channel; tip
(L), ring (R), sleeve (GND)
Impedance .................................... >5 kohms unbalanced, DC coupled
Maximum level ............................ +8.5dBu (unbalanced
Audio output
Number/signal type ................... 1 stereo, balanced/unbalanced
Connectors ................................... 1 3.5 mm captive screw connector, 5 pole
Impedance .................................... 50 ohms unbalanced, 100 ohms balanced
Maximum level (Hi-Z) ................ >+14dBu, balanced or unbalanced at stated
%THD+N
Maximum level (600 ohm) ......... >+0dBu, balanced or unbalanced at stated
%THD+N
0dBu = 0.775 volts (RMS).
General
Power ............................................ 100VAC to 240VAC , 50/60 Hz, 5 watts,
external, autoswitchable; to 9VDC, 1A
power supply.
Temperature/humidity .............. Storage -40° to +158°F (-40° to +70°C) /
Rack mount .................................. No
Enclosure type .............................. Metal
Enclosure dimensions ................. 1.0" H x 5.7" W x 4.5" D
Product weight ............................. 0.6 lbs (0.3 kg)
Shipping weight ........................... 3 lbs (1.4 kg)
Vibration ....................................... ISTA/NSTA 1A in carton (International
Listings .......................................... UL, CUL
Compliances ................................. CE
MTBF ............................................. 30,000 hours
Warranty ....................................... 3 years parts and labor
10% to 90%, non-condensing
Operating +32° to +122°F (0° to +50°C) /
10% to 90%, non-condensing
2.5 cm H x 14.5 cm W x 11.4 cm D
Safe Transit Association)
www.extron.com
Specifications are subject to change without notice.
Extron Electronics, USA
1230 South Lewis Street Anaheim, CA 92805 USA
714.491.1500 Fax 714.491.1517
Extron Electronics, Europe
Beeldschermweg 6C 3821 AH Amersfoort The Netherlands +31.33.453.4040 Fax +31.33.453.4050
© 2002 Extron Electronics. All rights reserved.
Extron Electronics, Asia
135 Joo Seng Road, #04-01 PM Industrial Building Singapore 368363 +65.6383.4400 Fax +65.6383.4664
Extron Electronics, Japan
Daisan DMJ Building 6F 3-9-1 Kudan Minami Chiyoda-ku, Tokyo 102-0074 Japan +81.3.3511.7655 Fax +81.3.3511.7656
Loading...