Extron electronic MTP 1500RL User Manual
MTP 1500RL 15HD A SEQ • Setup Guide
This guide provides basic instructions for an experienced installer to set up and operate the Extron MTP 1500RL
15HD A SEQ twisted pair receiver.
For full details, see the MTP 1500RL 15HD A SEQ User Guide, available online at www.extron.com.
POWER
12V
1.0A MAX
INPUT
MTP
SELECT
GREEN
BLUE
DELAY
BUFFERED OUTPUT
MTP
RED
ADJUST
LEVEL
PEAKING
RGB
OUTPUT
MIN/MAX
AUDIO
MONO
LR
MTP 1500RL Series
H +
V +
CSYNC
SOG
ON
MTP 1500RL 15HD A SEQ
Installation and Setup
Step 1 — Mounting
Turn off or disconnect all equipment power sources. Mount the MTP 1500RL 15HD A SEQ receiver as required.
Step 2 — Connect Input
Connect the RJ-45 cable from an MTP transmitter to the Input port on the MTP 1500RL 15HD A SEQ receiver.
Terminate the cable as shown below right, using the same standard (A or B) at both ends.
RJ-45 Connector
Pins:
12345678
Insert Twisted
Pair Wires
VIDEO
END
SPARE
Pin T568A Wire
Color
T568B Wire
Color
1 White-green White-orange
2 Green Orange
3 White-orange White-green
4 Blue Blue
5 White-blue White-blue
6 Orange Green
7 White-brown White-brown
8 Brown Brown
NOTE: The transmitter and receiver are designed for and perform best with Extron Enhanced Skew-Free AV cable terminated in accordance
with the TIA/EIA T568A standard. CAT 5 cables are acceptable but less preferable. Using preterminated and tested cables is also
recommend, Cables terminated on site should be tested before use to ensure that they comply with Category 5 specifications.
Step 3 — Connect Outputs
Attach the applicable output cables (video, audio, and buffered output).
A. High resolution video output — Connect a display device to the 15-pin HD connector (RGB).
B. Audio connector — Connect an audio device to the 5-pole captive screw connector for mono audio output
MONO AUDIO
Mono output 1+
1
Mono output 1-
Mono output 2+
2
Mono output 2-
Sleeve(s)
Balanced Output
Do not tin the wires!
Mono output 1
NO GROUND.
Sleeve(s)
Mono output 2
NO GROUND.
Unbalanced Output
CAUTION
For unbalanced audio, connect the sleeve(s) to the ground contact.
DO NOT connect the sleeves to the negative (-) contacts.
C. Buffered output — Connect up to 5 daisy-chained MTP receivers to this RJ-45 connector.
MONO AUDIO
1
2
MTP 1500RL 15HD A SEQ • Setup Guide (Continued)
AA
Step 4 — Receiver DIP Switches
• H sync (H+) and V sync (V+) switches — Set these switches up (On) for positive
sync or down (Off) for negative sync.
• Composite Sync, SOG, and Video switches — Set these switches as shown in the
table on the right to output the indicated format.
• End Unit switch — Set this switch up if either of the following is true:
• The receiver being congured is the only receiver connected to the transmitter.
• The receiver being congured is the last receiver in a daisy-chained system.
Step 5 — Power
H +
V +
CSYNC
SOG
VIDEO
ON
END
Output
SPARE
Format
RGBHV
C Sync SOG Video
RGBS
RGsB
Component*
S-video*
Composite*
* Input video format must match.
a
Smooth
Ridges
POWER
12V
xA MAX
Rear
Panel
Wire the 2-pole captive screw connectors for the included external 12 VDC power supplies (see
image a on the right). Plug them into all units.
3/16"
(5 mm)
Grounding guidelines
Extron MTP 1500RL 15HD A SEQ products can be adversely affected by electrostatic discharge (ESD)
if they are not grounded correctly.
To prevent malfunctions or product damage, an experienced installer can correctly ground an Extron
SECTION A–A
Power Supply
Output Cord
Max.
MTP 1500RL 15HD A SEQ product in either of two ways:
• Ground the power input port — Insert one end of the grounding wire to the negative or ground pin on the
power input connector (see image a on the right). Tie the other end of the wire to an earth ground.
b
• Ground the chassis — Use a connector hex nut (see image b on the right). Tie the other end of the wire
to an earth ground.
If you have any questions about how to ground a product in a specic application, contact an Extron technical
support specialist.
Step 6 — Peaking and Level
Adjust image sharpness with the Peaking control. Increased peaking compensates for mid- and high-frequency detail
loss. The LED lights red when minimum (zero) and maximum peaking is reached.
Adjust image brightness using the Level control. View the image and adjust either control for the best image quality.
LEVEL
PEAKING
RGB
Step 7 — Skew Compensation
Pair skew can be measured with test equipment or by viewing a crosshatch test pattern. The SEQ receivers have
built-in skew compensation capabilities. Adjust the equalization as follows:
SELECT
A. Set the skew delay to zero for red, green, and blue by pressing and holding the Select button in for 3 seconds,
using a Tweeker or small screwdriver. When the Red, Green, and Blue LEDs all go out, release the Select button.
B. Use UTP cable test equipment or examine the displayed image to determine which video signal — red, green, or blue
— is shifted furthest to the right.
C. Adjust the furthest left video signal by using a Tweeker or screwdriver to press and release the Select button until the LED for the left-
shifted color lights.
D. Slowly rotate the Adjust control clockwise until the shifted color is properly aligned.
E. Repeat steps C and D to align the third color if needed.
RED
GREEN
BLUE
DELAY
ADJUST
Tie
Wrap
Ridges
Earth
Ground
MIN/MAX
Extron
MTP 1500RL 15HD A SEQ
PC
RGBHV
Audio
SPARE
END
VIDEO
SOG
CSYNC
V +
H +
ON
AUDIO
MONO
L R
OUTPUT
BUFFERED OUTPUT
INPUT
MTP
MTP
MTP 1500RL 15HD A SEQ
POWER
12V
0.5A MAX
500' (152 m) UTP Cable
(CAT 5/5e/6)
Extron
MTP T 15HD A
Audio
Flat Panel
Display
RGBHV
Extron
MTP 1500RL 15HD A SEQ
1,000' (305 m) UTP Cable
(CAT 5/5e/6)
Flat Panel
SPARE
Audio
END
VIDEO
SOG
CSYNC
V +
H +
ON
AUDIO
R
MONO
L
OUTPUT
BUFFERED OUTPUT
INPUT
MTP
MTP
MTP 1500RL 15HD A SEQ
POWER
12V
0.5A MAX
Display
RGBHV
Figure 1. Example of a typical MTP 1500RL 15HD A SEQ application
Extron USA Headquarters +1.800.633.9876 (USA/Canada Only) Extron USA - West: +1.714.491.1500 FAX: +1.714.491.1517 Extron USA - East: +1.919.850.1000 FAX: +1.919.850.1001
© 2013 Extron Electronics — All rights reserved. All trademarks mentioned are the property of their respective owners. www.extron.com
68-1554-50
Rev. B
01 13
Loading...