Extron electronic MTP User Manual
Setup Guide — MTP Series
Extron USA - West
Headquarters
+800.633.9876
Inside USA / Canada Only
+1.714.491.1500
+1.714.491.1517 FAX
Extron USA - East
+800.633.9876
Inside USA / Canada Only
+1.919.863.1794
+1.919.863.1797 FAX
Extron Europe
+800.3987.6673
Inside Europe Only
+31.33.453.4040
+31.33.453.4050 FA X
Extron Asia
+800.7339.8766
Inside Asia Only
+65.6383.4400
+65.6383.4664 FAX
Extron Japan
+81.3.3511.7655
+81.3.3511.7656 FAX
Extron China
+400.883.1568
Inside China Only
+86.21.3760.1568
+86.21.3760.1566 FAX
Extron Middle East
+971.4.2991800
+971.4.2991880 FAX
Power Supply
Output Cord
SECTION A–A
Ridges
Smooth
A A
Captive
Screw
Connector
Tie Wrap
3"
16 (5 mm) Max.
Reserved / Chroma+
Reserved / Chroma-
Mono audio+
Video- / Luma-
Mono audioReserved
Reserved
MTP signal
Composite / S-video
Video+ / Luma+
5
Pin
1
2
3
6
7
8
4
Wire color
White-green
NOTE If you are using Enhanced Skew-Free™ A/V cable,
use the TIA/EIA T568A standard only.
NOTE The pin assignment is different if you have shifted
the jumpers in “Pre-installation — Jumpers” above.
Refer to the MTP Series User’s Guide.
Green
White-orange
White-blue
Orange
White-brown
Brown
Wire color
T568A T568B
White-orange
Orange
White-green
White-blue
Green
White-brown
Brown
Blue Blue
Insert
TP Wires
Pins:
12345678
INPUT
LR
S-VIDEO
INPUT
VIDEO
LR
L R
L R
Unbalanced Stereo Input
Balanced Stereo Input
(high impedance)
(high impedance)
Ring
Sleeve (s)
Tip
Sleeve
Tip
Sleeve
Tip
Tip
Ring
Do not tin the wires!
Mono
Stereo
Jumpered for
Mono (Default)
1
MONO AUDIO
2
1
MONO AUDIO
2
Unbalanced Output
Balanced Output
Do not tin the wires!
Mono output 1-
Sleeve(s)
Mono output 1+
Mono output 2+
Mono output 2-
Sleeve(s)
Mono output 1
Mono output 2
NO GROUND.
NO GROUND.
SHARP
C GAIN
Y GAIN
SHARP
GAIN
S-video Receiver
Composite Video
INPUT
MTP T SV A RCA
VIDEO OUTPUT
L R
12V
0.5a
MAX
OUTPUT
SHARP
L R
INPUT
VIDEO
12V
0.5aMAX
MTP R SV A
XPA 1002
12
LIMITER/PROTECT
SIGNAL
OVER
TEMP
MTP T SV A RCA
Twisted Pair
Transmitter
MTP R SV A
Twisted Pair
Receiver
TP Cable
(up to 1,000')
DVD Player
Flat Panel
Display
Extron
SI 28
Surfacemount
Speakers
Extron
XPA 1002
Audio Powe
r
Amplier
Setup Guide — MTP Series, cont’d
This card provides quick start instructions for an experienced
installer to set up and operate any of the MTP A/V
transmission systems.
Pre-installation — Jumpers
The units are factory-set to handle mono audio and
so that one unit cannot remotely power another.
They can be set to handle stereo audio and provide remote power.
A stereo audio unit is only compatible with older generation units.
The jumper blocks’ appearance and location change with each unit.
Refer to the MTP Series User’s Guide to set the jumpers for the unit(s)
to be installed.
Installation
Step 1 — Mounting
Turn off or disconnect all equipment power sources and mount the MTP tansmitter and
receiver as required.
Step 2 — Transmitter inputs
N The drawings at right show the available connections. Your unit may look different.
• Plug a video source into the applicable input
connector:
S-video output connector — A 4-pin mini DIN
(Y/C) connector
Composite video Input connector — A female
BNC connector
• Plug an audio source into the applicable audio input
connector:
Two RCA connectors
5-pole captive screw connector — Wire the connector as shown below.
Step 4 — Receiver outputs
• Plug a video display into the applicable output connector:
S-video output connector — A 4-pin mini DIN (Y/C) connector
Composite video Input connector — A female BNC connector
• Plug an audio device into the applicable audio output connector:
Two RCA connectors
5-pole captive screw connector — Wire the connector as shown below.
C Connect the sleeves to ground (Gnd). Connecting the sleeve to a negative (-)
terminal will damage the audio output circuits.
Step 5 — Power
Wire the 2-pole captive screw connectors for the included
external 12 VDC power supplies as shown at right. Plug them
into both units.
Step 6 — Receiver’s Sharpness and Gain
• Sharpness—Adjusts the output image sharpness for long
cable runs.
• Gaincontrol—Adjusts the brightness of the output image to
compensate for long cable runs.
S-video receivers — There are separate controls for
luminance (Y) and chrominance (C). If the chrominance
setting is too low, the image may appear in monochrome.
Adjust the S-video gain until color appears.
Composite video receivers — There is only one gain control on composite video
MTP receivers.
N The control knobs are removable to limit access if desired.
Step 3 — TP cables
between units
Terminate a TP cable as shown
at right. Connect it between the
transmitter’s Output port and
the receiver’s Input port.
Example of a typical MTP S-video and audio application
68-732-50
Rev. B 02 09
Loading...