Extron electronic DTP T USW 233 User Manual

POWER
12V

2

--A MAX

Rx GTx RxTxG

RS-232 IR

RxTx

1

RGB, Y, R-Y, B-Y HDMI HDMI

SIG LINK

DTP OUT

AUDIO

CONTACT RS-232TALLY

3

123G 123+V

RESET

INPUTS

OVER DTPREMOTE

4 6

10 51 2 923

87

TP Wires

Pins:

IR Device

RS-232 Device

DTP T USW 233 • Setup Guide

This guide provides instructions for an experienced installer to set up and operate the
Extron DTP T USW 233 switching video transmitter. The DTP T USW 233 transmitter switches among
an analog video and two digital (HDMI) video inputs and, paired with a compatible receiver, can
extend the selected signal up to 230 feet (70 m). If the selected input is HDMI, the extended video
signal is HDCP-compliant.

Installation

Step 1 — Mounting

Turn off or disconnect all equipment power sources and mount the transmitter as required.

Step 2 — Making Connections

Inputs

Input 1 (RGB) connector — Connect a VGA cable between this port and the VGA output port of the analog video source.

a

Input 2 and 3 (HDMI) connectors — Connect HDMI cables between these ports and the HDMI output ports of the digital video

b

sources.

NOTE: See the LockIt

®

Lacing Brackets on page 3 of this guide for to securely fasten the HDMI connectors to the transmitter.

Audio input — Connect an unbalanced stereo audio source to this 3.5 mm mini stereo jack for an analog audio input.

c

NOTE: Audio is not embedded in the HDMI signal; it is transmitted simultaneously and is present on all inputs.

Over DTP RS-232 and IR pass-through

RS-232 and IR connector — To pass serial or infrared data or control signals on the Over

d

DTP RJ-45 output, connect the controlling device to the transmitter via the RS-232 and IR
captive screw connector. Connect the device to be controlled to the receiver.

DTP output to receiver

DTP RJ-45 connector — Connect the transmitter DTP Out port to the DTP In port on the

e

receiver. Extron recommends that you terminate both cable ends in accordance with the
following specications, at a minimum:

• TIA/EIA T 568B • CAT 6a, shielded

• 24 AWG, solid conductor

ATTENTION: Do not connect this device to a computer data or telecommunications network.

Signal LED — Lights when the unit is outputting a TMDS clock signal on the DTP output.

Link LED — Lights when a valid link is established between the units on the DTP cable.

Remote control

Remote Contact port — If desired, for contact closure control, plug a locally-contructed contact closure control device into this

f

3.5 mm, 4-pole captive screw port. Momentarily short the pin for the desired input (1, 2, or 3) to G to select that input. To force an
input to be always selected, leave the short in place.

NOTES:

• Contact closure control overrides front panel input selections.

• For contact closure control, auto-input switching mode must be off (see Selecting the switch mode on the next page).

TxRx

Gnd

OVER DTP

RxTx RxTxG

RS-232 IR

RxTx

Gnd

12345678

TIA/EIA T

Pin

Wire color

White-orange

1

Orange

2
3

White-green

4

Blue

5

White-blue
Green

6
7

White-brown

8

Brown

568B

1

DTP T USW 233 • Setup Guide (Continued)

Smooth

16 (5 mm) Max.

RS-232 Device

23

MODE

NORMAL

Press the button.
The LED lights

MODE

NORMAL

AUTO

Press the and HOLD the Mode button.

Release the Mode button.

23

HOLD

All three LEDs flash three times. Release the Input buttons.

SIGNAL

STATUS

Remote Tally port — If desired, to remotely identify the currently selected input, plug a locally-constructed device into this 3.5 mm,

g

4-pole captive screw connector. Connect the power wire for the device into the +V pin and connect the ground wire for the each
indicator into the corresponding tally output pin: 1, 2, or 3.

When an input is selected, by either contact closure or front panel selection, the corresponding tally output pin shorts to ground,
closing the circuit and lighting the connected indicator (LED).

Remote RS-232 port — Plug a serial RS-232 device into the switching transmitter via this rear

h

panel 3.5 mm, 3-pole captive screw connector for remote control of the switching transmitter.

Reset button

Reset button — This button initiates two levels of reset. For different reset levels, use an

i

Extron Tweeker or small screwdriver to press and hold the recessed button while the switcher
is running or while applying power. See the DTP T USW 233 User Guide, available at www.extron.com, for details.

Power

Power connector — Connect an IEC power cord between the included 12 VDC

j

power supply and a 100-240 VAC, 50-60 Hz source. Connect the power supply to
either unit, transmitter or receiver, as shown at right. Use the included tie-wrap to
strap the cord to the captive screw connector.

RxTx Gnd

Ridges

V

RS-232

GRxTx

Captive

Screw

Connector

REMOTE

NOTE: Only one power supply is required. A single power supply connected to

either unit in the pair powers both units. A power supply is included with the
transmitter.

Front panel Configuration port

Configuration port — Plug a PC or other controlling device into the switching transmitter via this front

a

panel mini-USB connector for remote conguration of the switching transmitter.

Operation

Switching inputs

Select the desired input by pressing the associated input button. Observe that the
LED for the selected input lights.

NOTE: The switcher must be in normal (manual) mode (see below).

Selecting the switch mode

In auto-input switching mode, the switcher selects to the highest numbered input
with a sync signal present. Turn auto-input switching mode on and off as follows:

1. Press and hold the Mode (Input 1) button.

2. Press and release the button for the desired mode:

Auto (Input 3) — The Auto Switch LED lights.

Normal (Input 2) — The Auto Switch LED goes off.

3. Release the Mode button.

Press and release the Auto or Normal button.

1 23

SECTION A–A

Power Supply

Output Cord

green.

1

3"

AA

AUTO

SWITCH

CONFIG

1

AUTO

Auto Switch lights (auto)
or goes out (normal).

AUTO

SWITCH

Locking and unlocking the front panel
(Executive mode)

The switcher has a front panel lock feature that locks the front panel. If you try to make
front panel input selections when the panel is locked, all front panel LEDs ash three
times. Toggle the front panel lock on and off by pushing and holding all three Input
buttons simultaneously for 5 seconds. All front panel LEDs ash three times.
Release the buttons.

Interpreting the Status LEDs

2

Signal LEDs (1 through 3) —Indicate that the switcher detects horizontal sync
(Signal LED 1) or TMDS clock (Signal LED 2 and Signal LED 3) signals on the associated input.

HDCP LEDs (2 and 3) —Indicate that the corresponding input signal is HDCP encrypted.

Press the and

1

MODE

HDCP

the all three Input buttons.

NORMAL

123

AUTO