Extron NAV 10SD 501, NAV 10SD 101 Setup Guide

IMPORTANT:

IMPORTANT:

NAV 10SD 501 and NAV 10SD 101 • Setup Guide

CLASS 1 LASER PRODUCT, see NAV 10SD 501 and NAV 10SD 101 User Guide at www.extron.com

WARNING: The NAV 10SD 501 and NAV 10SD 101 output continuous invisible light (Class 1 rated), which may be harmful to the

eyes; use with caution.

•

Do not look into the ber optic cable connectors or into the ber

• Plug the attached dust caps into the optical transceivers when the ber cable is unplugged.

optic cables themselves.

Go to www.extron.com for the complete

user guide, installation instructions, and

specifications before connecting the

product to the power source.

AVERTISSEMENT : Le NAV 10SD 501 et le NAV 10SD 101 émettent une lumière invisible en continu (équipement de classe 1) qui

peut être dangereuse pour les yeux ; à utiliser avec précaution.

•

Ne pas xer dir

ectement les connecteurs optiques ou les câbles bre optique.

• Associez les bouchons anti-poussière à l’ensemble émetteur/récepteur optique lorsque le câble bre optique est débranché.

This guide provides instructions for an experienced installer to install the Extron NAV 10SD 501 and NAV 10SD 101 scaling decoders and
to make all connections. One or more compatible Extron NAV encoders and one or more decoders form an AV distribution and switching
matrix on a managed 10G IP network.

NOTE: For more information on any subject in this guide, see the NAV 10SD 501 and NAV 10SD 101 User Guide, available at

www.extron.com

.

Installation

Step 1 — Mounting

Turn off or disconnect all equipment power sources and mount the decoder as required.

Step 2 — Rear Panel Connections

POWER
12V

2.0 A MAX

POWER
12V

2.0 A MAX

Figure 1. NAV 10SD 501 and NAV 10SD 101 Rear Panel Features

NAV 10G port — Use a pair of fiber cables to connect to an Ethernet LAN on which one or more encoders also reside for streaming

A

and control.

NOTE: Ensure that you use the proper ber cable for your encoder. Typically, singlemode ber has a yellow jacket

and multimode cable has an orange or aqua jacket.

AUDIO

L

HDMI

CCCHHH EEE GGGAAA

HDMI

DDD

AUDIO

L

CONTROLOUTPUT

RS-232 IRR

Tx Rx GSG

CONTROLOUTPUT

RS-232 IRR

Tx Rx GSG

USB 2.0

5V/200 mA

LAN

NAV 10G EXT

FFF BBB

LAN

NAV 10G

NAV 10SD 501

RESET

NAV 10SD 101

RESET

Extension port (NAV 10SD 501 only) — If desired, connect another networked device to this port. The port acts as a networked 1G

B

switch to the NAV 10G port.

HDMI output port — Connect an HDMI cable between this port and an HDMI display (or a DVI display, with an appropriate adapter).

C

See LockIt

Audio output port — This 5-pole, 3.5 mm captive screw connector outputs the streamed, unamplified, line level analog audio. Connect

D

an audio device, such as an audio amplifier or powered speakers (see Analog audio output connector on page 6 to wire the
connector).

®

Lacing Brackets on page 6 to use the LockIt HDMI Cable Lacing Bracket to secure the connector to the decoder.

1

Control RS-232/IR port (see figure 1 on page 1) — Connect a serial RS-232 signal, a modulated IR signal, or both to this 3.5 mm,

E

5-pole captive screw connector for bidirectional RS-232 and IR communication with connected remote controlled devices using an
Extron control system (see Control connector on page 6 to wire the connector).

USB 2.0 port (NAV SD 501 only) — Connect a USB Type-C cable to USB host or a USB device. See LockIt® Lacing Brackets on

F

page 6 to securely fasten the USB connector to the decoder.

NOTE: This connector is limited to supplying 200 mA in USB device mode.

Reset button — This button initiates three modes of reset (see the NAV 10SD 501 and NAV 10SD 101 User Guide, available at

G

www.extron.com, for details).

Power connector (optional) — Plug the included external 12 VDC power supply into this 2-pole connector (see Power connector on

H

page6 to wire the connector).

Step 3 — Front Panel Configuration Port Connection

CONFIG

BBB

CONFIG

Figure 2. NAV 10SD 501 and NAV 10SD 101 Front Panel Features

Configuration port — Connect a PC to the decoder via this front panel mini-USB connector for configuration of the unit. The

A

port uses IP over USB technology; the IP address is always 203.0.113.22 and CANNOT be changed. The Config port is also
discoverable via Toolbelt (see the NAV 10SD 501 and NAV 10SD 101 User Guide, the guide and Toolbelt are available for download at

www.extron.com).

Indicators

Power LED — Indicates power and startup status, as follows:

B

Blinking

•

Lit steadily

•

NAV LEDs — Indicates status of the streaming input, as follows:

C

• VIDEO — Indicates status of the video stream.

• Lit steadily — The decoder is receiving a video stream.

• Blinking — A video stream is being decoded, but network errors are present that affect the video quality.

• HDCP — The video stream is HDCP encrypted.

• AUDIO LED — Indicates status of the audio stream

• Lit steadily — The decoder is receiving an audio stream.

•

Blinking

• USB LED (NAV 10SD 501 only) — Indicates status of the USB stream.

• Lit Steadily - The decoder is actively receiving and sending a NAV USB stream

• Unlit — The decoder is not actively sending and receiving a NAV USB Stream.

• Blinking - The decoder is unable to establish a NAV USB stream.

Audio LEDs — Indicate the active audio output, as follows:

D

• HDMI — The embedded HDMI audio output is selected.

• ANALOG — The analog audio output is selected.

2

NAV

VIDEO

HDCP

AUDIO

USB

AAA

NAV

VIDEO

HDCP

— The unit is receiving power and is booting up.

— The unit is receiving power and is operational.

AUDIO

AUDIO LAN IDUSB

HDMI

ANALOG

DDD

AUDIO LAN ID

HDMI LNK

ANALOG

HOST

ACTIVE

EEECCC

.

— An audio stream is being decoded, but network errors are present that affect the audio quality.

NAV EXT

-LNK-

-ACT-

NAV 10SD 501

EEE FFF

ACT

NAV 10SD 101