Extech EXT-1, EXT-3, EXT-5 User guide [ml]
User's Guide
Telescoping Handle Mango telescópico Poignée télescopique Alça Telescópica Teleskopgriff
Manico Telescopico
Models EXT-1, EXT-3, EXT-5
Telescoping Handle
Congratulations on your purchase of this Extech Telescoping Handle. This accessory can be used with several Extech meters to enable measurements in areas normally unreachable.
Operation
The meter sensor is attached to the top of the pole using the tripod screw.
1. |
Release the head cover (3) by pressing the two release |
|
|
|
2 |
||||
|
|||||||||
|
|
|
|
|
|
|
3 |
||
|
latches (1). |
|
|
|
|
|
|
|
|
2. |
1 |
|
|
|
|
|
|
1 |
|
Secure the meter to the head tripod screw (2) and replace the |
|
|
|
|
|
|
|
|
|
|
head cover |
|
|
|
|
|
|
|
|
3. |
Adjust the head to the needed angle and tighten with the |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
|
locking screw (4) |
|
|
|
|
|
|
|
|
|
4 |
|
|
|
|
|
|||
|
|
|
|
|
|
|
|||
Extend the pole sections by twisting the locking nuts as shown and then securing at the desired length.
NOTE: The extended pole should only be used in the vertical position. If used in the horizontal position with the pole extended the meter’s weight will damage the mechanism.
Specifications
Length |
EXT-1: Extended; 1.3m (4 ft), Collapsed; 0.47m (1.5ft) |
|
|
EXT-3: Extended; 3.2m (9.8ft), Collapsed; 1m (3.3ft) |
|
|
EXT-5: Extended; 5.2m (16.4ft), Collapsed; 1.5m (4.9ft) |
|
Weight |
EXT-1: 386g |
(0.85lbs.) |
|
EXT-3: 703g |
(1.55lbs.) |
|
EXT-5: 998g |
(2.2lbs.) |
Adjustment rings |
Polycarbonate with infused fiberglass |
|
Shafts |
Iodized black extruded aluminum |
|
Copyright © 2011 Extech Instruments Corporation (a FLIR company)
All rights reserved including the right of reproduction in whole or in part in any form. www.extech.com
2 |
EXT-1-3-5-EU-V1.0 11/11 |
Mango telescópico
Agradecemos su compra de este Mango telescópico Extech. Este accesorio se puede usar con varios medidores Extech para realizar mediciones en lugares difíciles de alcanzar.
Operación
El sensor del medidor se sujeta en la parte superior del poste con el tornillo del trípode.
1. Para soltar la tapa de la cabeza (3) presione las dos trabas |
|
|
2 |
||||
|
|||||||
|
|
|
|
|
|
3 |
|
(1). |
|
|
|
|
|
|
|
1 |
|
|
|
|
|
1 |
|
2. Asegure el medidor a la cabeza con el tornillo del trípode (2) y reemplace la tapa de la cabeza
3. Ajuste la cabeza al ángulo necesario y apriete e l tornillo de
trabe (4)
4
Extienda las secciones del poste girando las tuercas como se muestra y luego aprieta según el largo deseado.
NOTA: El poste extendido sólo se debe usar en posición vertical. Si se usa en posición horizontal el peso del medidor causará daños mecánicos al poste extendido.
Especificaciones
Longitud |
EXT-1: Extendido; 1.3m (4 ft), Colapsado; 0.47m (1.5ft) |
||
|
EXT/3: Extendido; 3.2m |
(9.8 ft), Colapsado; 1m (3.3ft) |
|
|
EXT/5: Extendido; 5.2m |
(16.4 ft), Colapsado; 1.5m (4.9 ft) |
|
Peso |
EXT-1: 386g (0.85 lbs.) |
||
|
EXT/3: 703g |
(1.55 lbs.) |
|
|
EXT/5: 998g |
(2.2 lbs.) |
|
Anillos de ajuste |
Policarbonato con infusión de fibra de vidrio |
||
Tubos |
Aluminio extruido anodizado negro |
||
Copyright © 2011 Extech Instruments Corporation (Una Empresa FLIR)
Reservados todos los derechos, incluyendo el derecho de reproducción total o parcial en cualquier medio. www.extech.com
3 |
EXT-1-3-5-EU-V1.0 11/11 |
Loading...