Evolution SDS4-800 User Manual

SDS4-800 HAMMER DRILL

Instruction Manual

Read instructions before operating this tool.

www.evolutionbuild.com

01/03/2016

SDS4-800 HAMMER DRILL

FIG 1 FIG 2

FIG 3 FIG 4

TABLE OF CONTENTS

EC - Declaration of Conformity Important Information 12 Month Limited Warranty General Safety Rules Labels & Symbols Additional Speciﬁc Safety Rules Speciﬁcation Assembly Functional Description Operation Maintenance Environmental Protection Service Parts Lists

EC - DECLARATION OF CONFORMITY

We, the importer Evolution Power Tools Ltd. Venture One Longacre Close Shefﬁeld S20 3FR

Declare that the product Part numbers: ZIC-SD6A-20 Evolution: SDS4, SDS4-800 SDS 4 Function Hammer Drill

Complies with the essential requirements of the following European Directives: 2006/42/EC – Machine Directive

2004/108/EC – EMC Directive

(until Apr 19th 2016)

2014/30/EU – EMC Directive (starting from Apr 20th 2016) 2002/95/EC – Restriction of the use of Certain Hazardous Substances in Electrical and Electric Equipment

Standards and Technical speciﬁcations referred to:-

EN55014-1 : 2006 EN55014-2 : 2001+A1 EN61000-3-2 : 2000 EN61000-3-3 : 2005+A2 EN60745-1 : 2006 EN60745-2-6 : 2007+A11

All documentation is held on ﬁle at the above address and is available, on request for review.

IMPORTANT

Please read these operating and safety instructions carefully and completely. For your own safety, before using this equipment check that the voltage is correct and that all handles and parts are ﬁrmly secured. If you are uncertain about any aspect of using this equipment, please contact our Technical Helpline.

Technical Helpline UK 0870 609 2297 Technical Helpline USA 1-866-EVO-TOOL

SDS HAMMER DRILL

Congratulations on your purchase of an Evolution Power Tools SDS 4 Function Hammer Drill. Please complete your product registration on line to validate your machine’s warranty period and ensure prompt service if needed. We sincerely thank you for selecting a product from Evolution Power Tools.

WARRANTY

12 MONTH LIMITED WARRANTY. Evolution power tools reserves the right to make improvements and modiﬁcations to design without prior notice.

Evolution Power Tools will, within twelve (12) months from the original date of purchase, repair or replace any goods found to be defective in materials or workmanship. This warranty is void if the tool being returned has been used to drill / chisel materials beyond the recommendations in the Instruction Manual or if the drill has been damaged by accident, neglect, or improper service. This warranty does not apply to machines and / or components which have been altered, changed, or modiﬁed in any way, or subjected to use beyond recommended capacities and speciﬁcations. Electrical components are subject to respective manufacturers’ warranties. All goods returned defective shall be returned prepaid freight to Evolution Power Tools. Evolution Power Tools reserves the right to optionally repair or replace it with the same or equivalent item. There is no warranty – written or verbal – for chisel / drill bits. In no event shall Evolution Power Tools be liable for loss or damage resulting directly or indirectly from the use of our merchandise or from any other cause. Evolution Power Tools is not liable for any costs incurred on such goods or consequential damages. No ofﬁcer, employee or agent of Evolution Power Tools is authorized to make oral representations of ﬁtness or to waive any of the foregoing terms of sale and none shall be binding on Evolution Power Tools. Questions relating to this limited warranty should be directed to the company’s head ofﬁce, or call the appropriate Helpline number.

Print: Matthew Gavins - Group Chief Executive Date: 01/03/16

IMPORTANT SAFETY INSTRUCTIONS

To reduce the risk of electric shock, this equipment is ﬁtted

with an approved cord and plug for its intended country of use. Do not change the cord or plug in any way.

www.evolutionbuild.com

SDS4-800 HAMMER DRILL

GENERAL SAFETY RULES

Read and understand all instructions before operating this product. Failure to follow all instructions listed below, may result in electric shock, ﬁre and / or serious personal injury. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

WARNING! When using electric tools basic safety precautions should always be followed to reduce the risk of ﬁre, electric shock and personal injury including the following:

Read all these instructions before attempting to operate this product and save these instructions.

The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.

CAUTION! This is a very powerful machine. When using this drill it is essential that the following rules are followed.

1. When drilling it is common that the drill bit jams in the material being drilled. This will result in the drill trying to rotate around the drill bit and potentially to come out of your grip. This SDS drill has a safety clutch mechanism. This safety clutch mechanism will be activated and stop the drive to the drill, BUT only if you resist the initial forces caused by the jamming, by securely holding the drill with BOTH hands. As this is a powerful machine, these forces are signiﬁcant.

2. ALWAYS ensure that the front handle is ﬁrmly ﬁxed in place and secure.

3. The front and rear handles must be ﬁrmly held to resist any movement of the drill when the drill or drill bit becomes jammed.

4. ALWAYS use the drill when standing on a ﬁrm and secure platform or on the ground. (DO NOT USE ON LADDERS OR STEPS)

5. NEVER start the drill with the drill bit jammed in position.

6. DO NOT stretch to hold the drill. Do not drill above shoulder height or below knee height, as the drill cannot be securely held.

7. This machine is not suitable for use with TCT core drill bits, diamond core drill bits, and diamond drill bits.

GENERAL SAFETY RULES

When using electric tools, basic safety precautions should always be followed to reduce the risk of ﬁre, electric shock and personal injury.

Please read all of these instructions before attempting to operate this machine. Save this manual for future reference.

1. Keep work area clear. Cluttered work areas invite accidents.

2. Consider work area environment. Do not expose tools to rain. Do not use tools in damp or wet locations. Keep work

area well lit. Never use tools near ﬂammable liquids or gases.

3. Protect yourself against electric shock. Avoid body contact with earthed or grounded surfaces.

4. Keep other people away. Do not let others, especially children, come close to the work, and touch the tool or the extension lead. Keep them away from the work area.

5. Store idle tools. When not in use, tools should be stored in a dry locked-up place, out of children’s reach.

6. Never force the tools. Your tools will be more efﬁcient and safer when used at the rate for which they were intended.

7. Use the right tool. Do not force small tools to do the job of a heavy duty tool. Do not use tools for purposes not intended; for example do not use circular saws to cut tree limbs or logs.

8. Dress properly. Do not wear loose clothing or jewelry which may get caught in moving parts. Non-skid footwear is recommended when working outdoors. If you have long hair, tie it back and wear protective hair covering.

9. Use protective equipment. Use safety glasses. Use face or dust mask if cutting operations create dust.

10. Connect dust extraction equipment. If the machines have a connection for dust extraction equipment, ensure these are connected and properly used.

11. Do not damage the cable. Never pull the power cable to disconnect the machine. Keep the cable away from heat, oil and sharp edges.

12. Secure workpiece. Where possible, use clamps or a vice to hold the workpiece. It’s much safer than using your hands.

13. Don’t over reach. Keep proper footing and balance at all times.

14. Maintain tools in good working condition.

Keep cutting tools sharp and clean for better performance and optimum safety. Follow instructions for lubricating and changing accessories. Inspect power cables regularly and, if damaged, have them replaced by an authorised service centre. Inspect extension cables regularly and replace immediately if damaged. Keep handles dry, clean and free from oil and grease at all times.

15. Disconnect tools. Disconnect tools from the power supply when not in use, before any maintenance operation and when changing accessories such as blades, bits, cutters, etc.

16. Remove adjusting keys and spanners. Get into the habit of checking that adjusting keys and spanners have been removed from the machine before turning it on.

17. Avoid unintentional starting. Ensure switch is in “off” position before plugging in the machine.

18. Use proper extension leads. When the tool is used outdoors, use only extension leads intended for outdoor use and labelled as such.

19. Stay alert. Concentrate on what you are doing, use common sense and do not operate the tool when you are tired.

20. Check that no part is damaged. Before using a tool, make sure that it is in good working order. Check the alignment and condition of moving parts, mounting and any other aspect that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced by an authorised service centre unless otherwise indicated in this instruction manual. Do not use the tool if the switch does not turn on and off.

21. Warning. The use of any accessory or attachment other than one recommended in this instruction manual may

present a risk of personal injury.

22. Have your tool repaired at an authorised service centre. This electric tool complies with current safety rules.

Repairs should only be carried out by an authorised service centre using original spare parts. Failing this, the user could expose themselves to considerable danger.

HEALTH ADVICE

WARNING! When drilling, sanding, sawing or grinding, dust

particles will be produced. In some instances, depending on the materials you are working with, this dust can be particularly harmful to you (e.g. lead from old gloss paint).You are advised to consider the risks associated with the materials you are working with and to reduce the risk of exposure. You should:

-Work in a well-ventilated area.

-Work with approved safety equipment, such as dust masks that are specially designed to ﬁlter microscopic particles.

LABELS & SYMBOLS

WARNING! Do not operate machine if warning and /

or instruction labels are missing or damaged. Contact Evolution Power Tools for replacement labels.

Symbol Description

V Volts

A Amperes

Hz Hertz

Min

-1

Revolutions, strokes,

surface speed, orbits etc.

per minute

~ Alternating Current

No Load Speed

Double Insulated

Wear Safety Goggles

Wear Ear Protection

Do Not Touch

Wear Dust Protection

Restriction of Hazardous

Substances Directive

CE certiﬁcation

Waste electrical and

electronic equipment

To obtain an additional copy of your manual, please contact Evolution Power Tools at :

UK 0870 609 2297 USA 1-866-EVO-TOOL WEB www.evolutionpowertools.com

ADDITIONAL SPECIFIC SAFETY RULES

Do not let familiarity with this product (gained from repeated use) replace strict adherence to hammer drill safety rules. If you use this tool incorrectly you could suffer serious personal injury.

1. Hold tools by the insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring or its own cord. Contact with a

‘live’ wire will make exposed metal parts of the tool ‘live’ and shock the operator.

2. Always be sure you have a ﬁrm footing. Be sure no one is below you when using the tool in high locations.

3. Hold the tool ﬁrmly with both hands. Always use the side grip.

4. Keep hands away from rotating parts.

5. Do not leave the tool running. Operate the tool only

when hand-held.

6. Do not touch the bit or the workpiece immediately after operation; they may be extremely hot and could burn your skin.

7. Some materials contain chemicals which may be toxic.

Take caution to prevent dust inhalation and skin contact. Follow material supplier safety data.

CAUTION! Always unplug drill from the mains supply before changing the drill bit, servicing, cleaning or adjusting the drill.

SPECIFICATIONS

Evolution SDS4-800

Motor (230/110v – 50/60 Hz) 650W Impact Energy: 1.6J Speed Range: 0-1100min Machine Weight: 2.8 kg Product Dimensions (HxWxD) 210mm x 320mm x 85mm Recommended Maximum Duty Cycle: 30 mins Max. Drill Diameter (Steel): 13mm Max. Drill Diameter (Concrete): 20mm Max. Drill Diameter (Wood): 30mm Sound Pressure Level (Under Load): Lpa =88.6dB (A) Lwa =99.6dB (A) K = 3dB (A) Vibration:

h 14.015 m/s

K 1.5 m/s

The declared vibration total value has been measured in accordance with a standard test method and may be used for comparing one tool with another. The declared vibration total value may also be used in a preliminary assessment of exposure.

WARNING: The vibration emission during actual use of the power tool can differ from the declared total value depending on the ways in which the tool is used. The need to identify safety measures and to protect the operator are based on an estimation of exposure in the actual conditions

-1

www.evolutionbuild.com

+ 4 hidden pages