EVGA SuperNOVA 1600W PLATINUM operation manual
E006-00-000059
V2_201609
1600W PLATINUM Power Supply User Manual
Table of contents
Introduction...................................................................................................2
Safety Information........................................................................................2
What’s in the box..........................................................................................2
Features........................................................................................................3
Installation....................................................................................................3
Q&A...............................................................................................................5
SuperNOVA 1600P2 Cable Configuration...................................................6
SuperNOVA 1600P2 Specification...............................................................6
1
English
1600W PLATINUM Power Supply User Manual 1600W PLATINUM Power Supply User Manual
Introduction: Next Generation in Power
Thank you for purchasing the EVGA SuperNOVA 1600 P2 power supply. This power supply features 1600 watts of
continuous power delivery with 92% (115V) / 94% (220VAC~240VAC) efficiency and exceptionally clean voltage
output. What does that mean? The best stability, reliability, overclockability, and unparalleled control. The
SuperNOVA 1600 P2 is the ultimate tool for powering today's and tomorrow's biggest and toughest systems.
SuperNOVA 1600W PLATINUM
Safety Information
WARNING 1: This unit has no user-serviceable parts inside. Opening the casing presents a risk of electrocution and will
void the products warranty. EVGA will not be responsible for any result of improper use, including but not limited to,
any use of the product outside of its intended purpose or use inconsistent with the warranty terms available online.
(Warranty information is available at www.evga.com/support/warranty and this manual is available at
www.evga.com/manuals).
WARNING 2: Only use included cables or cables purchased from EVGA.com that are specifically labeled for your PSU.
Using incorrect cables runs the risk of catastrophic failure.
Features
STABLE POWER
The SuperNOVA PLATINUM series has outstanding electrical performance with ultra stable voltage and
extremely clean power output. This can help you achieve the highest possible overclock (optional) and provide
the most stable and reliable power to all components. The SuperNOVA PLATINUM series also has high efficiency
greater than 92% (115V) / 94% (220VAC~240VAC) and is 80 PLUS PLATINUM certified.
DUAL THERMAL CONTROL SYSTEM
The EVGA ECO Intelligent Thermal Control System provides silent operation at low loads, improved efficiency and
longer life span of the fan. Enabled by a simple switch directly on the power supply, the “No Fan Spin” feature is
ideal for users looking to reduce ambient noise overall. Save on energy costs and unnecessary fan usage with the
EVGA ECO Thermal Control System.
TOP QUALITY PROTECTIONS
The SuperNOVA PLATINUM series comes equipped with the most comprehensive protection set possible, including
Over Voltage Protection (OVP), Under Voltage Protection (UVP), Over Power Protection (OPP), Short Circuit
Protection (SCP), Over Current Protection (OCP), Over Temperature Protection (OTP). This product is also covered
by an exceptional 10-year warranty and EVGA’s legendary customer service and support.
SUPERIOR BUILD QUALITY
The SuperNOVA PLATINUM series is built to the highest standards, using 100% Japanese capacitors rated at
105 degrees Celsius and high quality brand-name semiconductor components for the highest performance and
reliability. The Ultra Quiet 140mm double ball bearing fan provides adequate cooling to allow near silent operation
when not needed and proper cooling during heavy load operation.
MODULAR DESIGN
Reduce clutter in the case, improve ambient temperatures with better airflow overall and provide a clean look to
any system. Fully Modular PSU designs allow the user to disconnect the cable from the power supply side if they
are not needed for the specific configuration. This can help free up space inside the case and improve cable
management as well as airflow throughout the system. EVGA offers fully modular designs on all P2 series and
include a cable storage bag in case you plan to upgrade or add more components for storage.
Installation
What’s in the Box
Included with your EVGA 1600W PLATINUM power supply offers the following items for proper installation and
optional testing:
(1) EVGA Power Supply
(1) EVGA Manual
(4) Mounting Screws
(1) EVGA PSU Tester (24-Pin)
(1) EVGA Cable Bag
(1) 24-Pin ATX Cable
(2) 8(4+4)-Pin EPS12V CPU Cables
(4) 8(6+2)-Pin PCI-E VGA Cables
(5) 6-Pin + 8(6+2)-Pin PCI-E VGA Cables
(3) 4 SATA cables
(1) 3 Molex cable
(1) 2 Molex + 2 SATA cable
(2) Floppy adapters
(1) Power Cord cable (optional)
2 3
1. Remove the power supply from its packaging.
2. (Optional) Using the provided PSU testing tool, connect the 24pin cable to the
PSU, then attach the testing tool to the 24pin cable. Connect the ATX power cable
to the PSU and plug the PWR cable into the outlet or surge protector/UPS you plan
to use. Once connected, turn the power switch to the ON position. (If the ECO mode
is set to ON, the fan will not spin)
Please note: If you are using a water cooling configuration, this testing tool
provides a simple, safe, option for bleeding/draining/testing water cooling
components without the need of a paperclip or other device.
EnglishEnglish
1600W PLATINUM Power Supply User Manual 1600W PLATINUM Power Supply User Manual
3. Use the screws provided with your case to install the power supply into your
computer. NOTE: It is recommended to install the power supply with the fan
facing down. However, if your case places the power supply at the bottom of
the case and there are no ventilation holes available, it may be best to install
the power supply with the fan facing up for greater efficiency and reliability.
4. Connect the 24-pin ATX cable to the motherboard.
5. Connect the 4+4-pin EPS12V cable to the motherboard.
(Optional) – If you plan on extreme overclocking and your
motherboard supports additional 8pin or 4pin CPU power
connectors, connect the second 4+4-pin EPS12V cable. This is
only needed for heavy overclocking or for Dual CPU motherboards.
6. Connect the 6/6+2-pin PCI-E cables to your graphic card(s).
NOTE 1: Do not attempt to plug an 8-pin PCI-E cable into a 6-pin
connector without first detaching the two extra pins.
NOTE 2: We recommend to use a single PCI-E cable to connect per
port on graphic cards if your video card requires high power such as
equipped with more than 2 PCI-E connectors 6pin + 8pin and 8pin + 8pin.
7. Connect SATA power cables to all data drives or optical drives.
(hard drives, solid state drives, optical drives)
8. Connect the peripheral “Molex” 4-pin connectors for fans, pumps,
legacy components and other devices/adapters.
9. Connect the AC power cord to your power supply and to the wall.
Check all connections to assure a solid connection and turn the
power switch on the power supply to the ON position.
Q&A
Q: I see there are more than 4 screw holes on the back of the power supply, but the packaging only offers (4)
screws, are some missing?
A: Nothing is missing; you will only need to attach the EVGA power supply to the case with 4 screws.
The power supply offers more than (4) holes to provide optimal compatibility for today’s varied case designs.
Q: My EVGA Power Supply includes (2) EPS cables for my motherboard, do I need to connect up both?
A: Motherboards only require (1) 4+4 or 8pin EPS connection. On some models, an additional 4+4pin or 8pin
connection on the motherboard may be available for dual CPU configurations or for extreme over clocking. If your
motherboard support dual 4+4pin EPS connections, please refer to your motherboard manufacturer’s manual for
details on the proper function and power if the EPS connections.
Q: What is the ECO Thermal Control System?
A: The ECO Thermal Control System, when enabled, allows the fan on your EVGA power supply to shut off
during low to moderate operation loads. The EVGA power supply’s fan will automatically turn back on when
needed, based on the temperature the power supply reaches. The fan will also increase in RPM when needed,
based on the load operation being requested from the components connected. This prevents unnecessary
rotation, reduces ambient noise levels and will increase the life span of the fan due to the fan not spinning when
not required.
Please Note: If the ECO Thermal Control is disabled the fan will always spin, even at low loads. The fan will also
increase in RPM as needed automatically, based on the power draw from attached components
Q: What if I want to use power adapters for my video card(s)/motherboard/peripherals?
A: EVGA always recommends the use of direct power connections from the power supply to power the video
card(s), motherboard connections and other auxiliary power connections for optimal power distribution.
Q: Does it matter which end of the cable I plug into the power supply?
A: Yes, the connections going to the power supply, will not have “break downs” like the EPS (CPU) has 4+4 on
one side and full 8-pin on the other. Another example is the 24-pin cable, you can see on the PSU side it is a
total of 28 pins, where the 24-pin connection will go to the motherboard directly. Check each cable as it is labeled
appropriately to match the power supply side and connect only the same “matching” cable directly to the power
supply as referenced on each connector.
Q: I plugged everything in and the system will not POST, or goes into a boot loop.
A: Power the PSU off and double check to make sure all the power connections are firmly seated on the
motherboard and on the PSU side. If the problem persists you will want to try testing the 24-pin using the
provided PSU tester. If the PSU tests ok, then you will want to try testing the motherboard in “barebones” to get
a POST, removing everything except for the CPU and heatsink, 1 stick of RAM, 24-pin and 8-pin power connections.
Q: If I have an issue or a question, can I get support?
A: ALL EVGA products are backed by top tier warranties as well as 24/7 technical support. Support can be
reached for your power supply at 888-881-3842 option 1, option 3. Or contact us via email at support@evga.com.
4 5
EnglishEnglish
1600W PLATINUM Netzteil Bedienungsanleitung1600W PLATINUM Power Supply User Manual
SuperNOVA 1600P2 Cable Configuration
Modular Connector Cables Cable Color
MB
CPU1
CPU2
VGA1
VGA2
VGA3
VGA4
VGA5
VGA6
VGA7
VGA8
VGA9
SATA1
SATA2
SATA3
PERIF
PERIF/SATA
FDD
1 x ATX 24-Pin
2 x EPS/ATX12V 8(4+4)-Pin
4 x PCI-E 8(6+2)-Pin
5 x PCI-E 6-Pin + 8(6+2)-Pin
3 x SATA 5-Pin x 4
1 x Molex 4-Pin x 3
1 x Molex 4-Pin x 2 + SATA 5-Pin x 2
2 x Molex to FDD Adapters
Black
SuperNOVA 1600P2 Specifications
SuperNOVA 1600W PLATINUM
AC Input
DC Output +5V +3.3V +12V -12V +5Vsb
MAX output, A
Combined, W
Output power,
Pcont
24A 24A 133.3A 0.5A 3A
120W 1599.6W
115-240 VAC, 17-10A, 60/50 Hz
1600W @ +50°C
+50°C ambient @ full load
6W 15W
Inhalt
Einführung.......................................................................................................8
Sicherheit........................................................................................................8
Lieferumfang...................................................................................................8
Merkmale.........................................................................................................9
Installation.......................................................................................................9
Häufige Fragen..............................................................................................11
SuperNOVA 1600P2 Kabelkonfiguration......................................................12
SuperNOVA 1600P2 Spezifikationen............................................................12
Dimensions: 85mm (H) x 150mm (W) x 220mm (L)
Over Voltage Protection, Under Voltage Protection, Short Circuit Protection, Over Power Protection,
Over Current Protection, Over Temperature Protection.
6 7
DeutschEnglish
1600W PLATINUM Netzteil Bedienungsanleitung1600W PLATINUM Netzteil Bedienungsanleitung
Einführung: Leistungsstarke Netzteile einer neuen Generation
Vielen Dank, dass Sie sich für den Kauf eines EVGA SuperNOVA 1600 P2 Netzteil entschieden haben. Dieses
Netzteil bietet 1600 Watt Dauerleistung bei 92% (115V) / 94% (220VAC~240VAC) Effizienz und außergewöhnliche,
stabile Spannungsversorgung. Was das bedeutet? Beste Stabilität, Zuverlässigkeit, Übertaktbarkeit, bei
unvergleichbarer Kontrolle. Das SuperNOVA 1600 P2 ist das ultimative Netzteil, für die Versorgungsanforderungen,
der taffesten und größten Systeme von heute und morgen.
Sicherheit
WARNHINWEIS 1: Im Gerät befinden sich keine vom Benutzer zu wartenden Teile. Beim Öffnen des Gehäuses besteht
das Risiko eines Stromschlags, und die Produktgarantie verfällt. EVGA übernimmt keinerlei Haftung für Folgen
unsachgemäßer Verwendung. Hierzu zählt unter anderem die Verwendung des Produkts für einen anderen als den
vorgesehenen Verwendungszweck oder eine Verwendung, die nicht den online einsehbaren Garantiebedingungen
entspricht. (Die Garantiebedingungen sind auf eu.evga.com/support/warranty einsehbar. Dieses Handbuch ist auf
www.evga.com/manuals einsehbar.)
WARNHINWEIS 2: Verwenden Sie nur mitgelieferte oder direkt von EVGA bezogene Kabel für Ihr Netzteil.
Die Nutzung anderer Zubehörteile kann zu schwerwiegenden Fehlern führen.
SuperNOVA 1600W PLATINUM
Lieferumfang
Im Lieferumfang des EVGA 1600W PLATINUM sind folgende Komponenten für die korrekte Installation, sowie
optionale Funktionstests enthalten:
(1) EVGA Netzteil
(1) EVGA Handbuch
(4) Montageschrauben
(1) EVGA Netzteil-Tester (24-Pin)
(1) EVGA Kabelbeutel
(1) 24-Pin ATX-Kabel
(2) 8(4+4)-Pin EPS12V CPU-Kabel
(4) 8(6+2)-Pin PCI-E VGA-Kabel
(5) 6-Pin + 8(6+2)-Pin PCI-E VGA-Kabel
(3) 4 SATA-Kabel
(1) 3 Molex-Kabel
(1) 2 Molex-Kabel+ 2 SATA-Kabel
(2) Floppy-Anschlusse
(1) Netzkabel (optional)
8 9
Merkmale
STABILE LEISTUNG
Die PLATINUM-Serie liefert hervorragende elektrische Leistung mit extra stabiler Spannung und extrem sauberem
Output. Sie ermöglicht maximale Übertaktung (sofern erwünscht) und versorgt sämtliche Komponenten
zuverlässig mit stabiler Leistung. Die SuperNOVA PLATIN Serie bietet eine ausgezeichnete Effizienz mit mehr als
92% (115V) / 94% (220VAC~240VAC) und ist 80 PLUS PLATIN zertifiziert.
DUALES THERMAL CONTROL SYSTEM
Das EVGA ECO Intelligent Thermal Control System sorgt für leiseren Betrieb bei geringerer Auslastung,
verbesserte Effizienz und eine längere Lebensdauer des Lüfters. Die über einen einfachen Schalter direkt am Netzteil
aktivierbare „No Fan Spin“ Funktion ist ideal, um den Geräuschpegel zu senken. Das EVGA ECO Thermal
Control System reduziert die Energiekosten und vermeidet überflüssigen Lüfterbetrieb.
ERSTKLASSIGE SCHUTZMERKMALE
Die PLATINUM-Serie verfügt über umfangreiche Schutzmerkmale, darunter Überspannungsschutz (Over Voltage
Protection, OVP), Unterspannungsschutz (Under Voltage Protection, UVP), Überlastschutz (Over Power
Protection, OPP), Kurzschlussschutz (Short Circuit Protection, SCP) und Überstromschutz (Over Current
Protection, OCP), Überhitzungsschutz (Over Temperature Protection, OTP). Noch mehr Sicherheit bieten zudem die
außergewöhnliche 10-Jahres-Garantie sowie der legendäre EVGA Kundendienst und Support.
HERVORRAGENDE QUALITÄT
Die P2-Serie entspricht den höchsten Baustandards. Verbaut werden ausschließlich japanische Kondensatoren
mit einer Betriebstemperatur bis zu 105°C und hochwertige Halbleiterkomponenten namhafter Hersteller für
maximale Leistung und Zuverlässigkeit. Der ultraleise 140 mm Lüfter mit doppelter Kugellagerung sorgt für leise
Kühlung und beinahe lautlosen Betrieb bei geringer Belastung und für zuverlässige Kühlung bei hoher Belastung.
MODULARES DESIGN
Das aufgeräumte, übersichtliche Innere des PC-Gehäuses ermöglicht niedrigere Temperaturen durch verbesserten
Luftstrom. Durch das voll-modulare Netzteil-Design können die Kabel vom Netzteil abgetrennt werden, wenn sie für
die jeweilige Konfiguration nicht benötigt werden. Dadurch kann mehr Raum im PC-Gehäuse genutzt, die
Kabelführung verbessert und der Luftstrom im System optimiert werden. Alle Modelle der P2-Serie sind modular
und umfassen einen praktischen Beutel für die Kabelaufbewahrung, falls Sie später ein Upgrade planen oder
weitere Komponenten hinzufügen möchten.
Installation
1. Entnehmen Sie das Netzteil aus der Verpackung.
2. (Optional) Schließen Sie das 24-Pin-Kabel an das Netzteil und anschließend an
den mitgelieferten Netzteil-Tester an. Schließen Sie das ATX-Stromkabel an das
Netzteil an und schließen Sie das PWR-Kabel an die beabsichtigte Buchse bzw.
den Überspannungsschutz/Netzausfallschutz an. Schalten Sie anschließend den
Netzschalter in die Stellung EIN. (Ist der ECO Mode A an, dann bewegt sich der
Fan nicht)
Bitte beachten: Bei Konfigurationen mit Wasserkühlung stellt der Tester eine
einfache und sichere Methode zum Entlüften/Ablassen/Testen der
Komponenten der Wasserkühlung dar, ohne eine Büroklammer oder Ähnliches
zu Hilfe nehmen zu müssen.
DeutschDeutsch
Loading...