Evertz 500DA2Q-3G User Manual
500DA2Q-3G
3G/HD/SD-SDI Dual Reclocking Distribution Amplifi er (32-1x4 DAs in 3RU Rack Space)
The 500DA2Q-3G Dual 3G/HD/SD-SDI Reclocking Distribution Amplifi er
provides the highest density DA in the industry allowing up to 32-3Gb/s,
HD-SDI or SD-SDI Distribution amplifi ers in a 3RU rack space. This module
provides inexpensive distribution of your SMPTE ST 424 (3Gb/s), SMPTE ST
292-1 (1.5Gb/s), SMPTE ST 259-1 (270Mb/s), DVB-ASI or SMPTE ST 310-1
(19.4Mb/s) or any other SDI signal within the 143Mb/s to 1.5Gb/s range.
Features & Benefi ts
• Normal reclocked mode for SMPTE ST 424 (3Gb/s), SMPTE ST 292-1
(1.5Gb/s) and SMPTE ST 259-1 (270Mb/s)
• Jumper selectable non-reclocked mode for all other SMPTE ST 344-1,
SMPTE ST 259-1, SMPTE ST 310-1 and DVB-ASI data rates
• Fully hot-swappable from front of frame with no BNC disconnect required
• Independent isolated output drivers to ensure no cross channel loading effects
(i.e. no need to terminate unused outputs)
• Outputs maintain polarity from input to output for DVB-ASI applications
• Tally output on Frame Status bus upon loss of input signal for quality
monitoring
• VistaLINK
when installed in 500FR frame with 500FC VistaLINK
Input
• Two inputs
• SMPTE 424M (3Gb/s), SMPTE ST 292-1 (1.5Gb/s), SMPTE ST 259-1
(270Mb/s) when set to re-clocking mode.
®
-capable for remote monitoring via SNMP (using VistaLINK® PRO)
Serial Input
3G/HD/SD-SDI
Equalizer
®
Frame Controller
Reclocker
270 1.5G
Locked
3 Gb/s, 1.5 Gb/s, 270 Mbs
Reclocker
3G
The 500DA2Q-3G features two auto-equalized inputs and can be individually
set via jumpers for either reclocking or non-reclocking.
The 500DA2Q-3G is housed in the 500FR
exponent
frame that will hold up
to 16 modules.
• SMPTE ST 344-1 (540Mb/s), SMPTE ST 259-1 (360Mb/s, 143Mb/s), SMPTE
ST 310M-1
• (19.4Mb/s), DVB-ASI when not re-clocking
• Return Loss > 15dB to 1.5GHz and > 10dB up to 3GHz
• Auto equalization to 80m at 3Gb/s, 100m @ 1.5Gb/s and 350m @ 270Mb/s
Outputs
• Four reclocked outputs per input
• Return Loss > 10dB to 1.5GHz
• Wideband jitter < 0.2 UI
Card Edge LEDs
• Reclocker rate (3 LEDS)
• Reclocker locked
• Reclocker bypass
• Module Health Status
G
Cable Drivers
Serial Output
3G/HD/SD-SDI
The Complete Solution Provider
Reclocker Bypass
Reclocker
Bypassed
Reclocker
270 1.5G
Locked
3 Gb/s, 1.5 Gb/s, 270 Mbs
Reclocker
Reclocker Bypass
Reclocker
Bypassed
VistaLINK
Interface
Serial Input
3G/HD/SD-SDI
Carrier
Present
®
Control &
Indicators
Module
Health
Equalizer
Carrier
Present
Specifi cations
Serial Video Input:
Standards
Reclocked Mode: SMPTE ST 424 (3Gb/s), SMPTE
ST 292-1 (1.5Gbs),
SMPTE ST 259-1 (270Mb/s)
Non Reclocked Mode: SMPTE ST 344-1 (540Mb/s),
SMPTE ST 259-1 (360Mb/s,
143Mb/s), SMPTE ST 310-1
(19.4Mb/s), DVB-ASI
Connector: 2 BNC per IEC 61169-8 Annex A
Equalization:
Input A: Automatic to 65m @ 3Gb/s, 100m
@ 1.5Gb/s and 350m @ 270Mb/s
with Belden 1694A or equivalent
cable
Input B: Automatic to 80m @ 3Gb/s, 150m
@ 1.5Gb/s and 350m @ 270Mb/s
with Belden 1694A or equivalent
cable
Return Loss: > 15dB up to 1.5GHz
> 10dB up to 3GHz
Serial Video Outputs:
Number of Outputs:
2x4 Mode: 4 reclocked from each input.
Reclockers can by bypassed
separately for each input.
Connector: BNC per IEC 61169-8 Annex A
Signal Level: 800mV nominal
DC Offset: 0V ±0.5V
Rise & Fall Time: 200ps nominal
Ordering Information
500DA2Q-3G 3G/HD/SD SDI Dual Reclocking Distribution Amplifi er (32-1x4 DAs
in 3RU Rack Space)
Accessories
500FC VistaLINK® Frame Controller
CP-2116E-H Remote Control Panel
CP-2232E Remote Control Panel
3G
Cable Drivers
Serial Output
3G/HD/SD-SDI
Overshoot: < 10% of amplitude
Return Loss: > 10dB up to 1.5GHz
Wideband Jitter: < 0.2 UI HD
< 0.3 UI 3G
Electrical:
Voltage: +12V DC
Power: 6W
EMI/RFI: Complies with FCC Part 15 Class A
EU EMC Directive
Physical:
Number of slots: 1
Enclosures
500FR Compact High Density Distribution Frame
S501FR Standalone enclosure
exponent
Rev. 14-2
Loading...