Everpure QC7I Single - MC, QC7I Single - MH2, QC7I Single - MC2, QC7I Single - MH, QC7I Single - CV Installation And Operation Manual

Installation and Operation Guide

SELECTING A MOUNTING LOCATION

1. Give consideration to the weight of the unit when operating (filled with water). Operating weights
of the QC7I Systems are:

• Single System - 9 lbs. (4.0 kg.)

• Twin System - 19 lbs. (8.5 kg)

• Triple System - 27 lbs. (12 kg)

• Quad System - 36 lbs. (20 kg)

2. The location should allow for:

• Minimum clearance of 2-1/2” under the cartridge(s) so it can be lowered for removal and

replacement.

• Adequate space for “in” and “out” water line connections.

• Be near a drain for flushing and near a 110V outlet if the accessory (sold separately) Everguard

Low Pressure Alarm is used. See Figures 1-8.

3. If used in conjunction with the SR-X feeder, the SR-X should be mounted after the QC7I Series
Filter and as near the equipment as possible. If possible, keep at least 6” available to the left and
the right of the QC7I System in the event poor quality water conditions require the installation of
the optional Everpure E-Series Prefilter.

WARNING: Do not use the MH cartridge in conjunction with the SR-X.

QC7I Series Water Filters

Figure 1 – Single System

OPERATING SPECIFICATIONS*

Replacement

Combined Model Name

QC7I Single - MC MC 1.67 gpm (6.3 lpm) 9,000 gal (34,000 L)
QC7I Single - MC
QC7I Single - MH MH 1.67 gpm (6.3 lpm) 9,000 gal (34,000 L)
QC7I Single - MH

2

2

QC7I Single - TO
QC7I Single - CV CV 1.67 gpm (6.3 lpm) 7,500 gal (28,390 L)
QC7I Single - XCV XCV 1.67 gpm (6.3 lpm) 10,000 gal (37,850 L)
QC7I Single - XC XC 1.67 gpm (6.3 lpm) 12,000 gal (45,420 L)
QC7I Single - XC

2

QC7I Single - 7CB5 7CB5 2.5 gpm (9.4 lpm) 10,000 gal (37,850 L)
QC7I Single - 7CB5-K 7CB5-K 2.5 gpm (9.4 lpm) 10,000 gal (37,850 L)
QC7I Single - 7CB5-S 7CB5-S 2.5 gpm (9.4 lpm) 10,000 gal (37,850 L)

Combined Model Name

QC7I Twin - MC
QC7I Twin - MC
QC7I Twin - MH
QC7I Twin - MH

2

2

QC7I Twin - TO
QC7I Twin - CV CV 3.3 gpm (12.6 lpm) 15,000 gal (56,780 L)
QC7I Twin - XCV XCV 3.3 gpm (12.6 lpm) 20,000 gal (75,700 L)
QC7I Twin - XC
QC7I Twin - XC

2

QC7I Twin - 7CB5
QC7I Twin - 7CB5-K 7CB5-K 5.0 gpm (18.9 lpm) 20,000 gal (75,700 L)
QC7I Twin - 7CB5-S 7CB5-S 5.0 gpm (18.9 lpm) 20,000 gal (75,700 L)

Cartridge Flow Rate Capacity

2

MC

MH

2

1.67 gpm (6.3 lpm) 9,000 gal (34,000 L)

1.67 gpm (6.3 lpm) 9,000 gal (34,000 L)

TO 1.5 gpm (18.9 lpm) 30,000 gal (113,550 L)

2

XC

1.67 gpm (6.3 lpm) 12,000 gal (45,420 L)

Replacement

Cartridge Flow Rate Capacity

MC 3.3 gpm (12.6 lpm) 18,000 gal (68,000 L)

2

MC

MH 3.3 gpm (12.6 lpm) 18,000 gal (68,000 L)

2

MH

3.3 gpm (12.6 lpm) 18,000 gal (68,000 L)

3.3 gpm (12.6 lpm) 18,000 gal (68,000 L)

TO 3.0 gpm (37.8 lpm) 60,000 gal (227,100 L)

XC 3.3 gpm (12.6 lpm) 24,000 gal (90,840 L)

2

XC

3.3 gpm (12.6 lpm) 24,000 gal (90,840 L)

7CB5 5.0 gpm (18.9 lpm) 20,000 gal (75,700 L)

Figure 2 – Twin System

Figure 3 – Triple System

EV3024-87D DE05

Manufactured by Everpure

Figure 4 – Quad System

Replacement

Made in U.S.A.

WATER FILTER

EVERPURE

3072-61

QC7I

12

0

60

20

EVERPURE

PSI

PSI

0

4

0

1
0
0

80

OUTLET
3/8" FNPT

INLET

3/8" FNPT

27.50"

5.60"

16.60"

OUTLET

3/4" FNPT

INLET

3/4" MNPT

25.26"

24.60"

OUTLET

3/4" FNPT

INLET

3/4" MNPT

29.69"

21"

OUTLET

3/4" FNPT

INLET

3/4" MNPT

29.26"

Combined Model Name

QC7I Triple - MC
QC7I Triple - MC
QC7I Triple - MH MH 5.0 gpm (18.9 lpm) 27,000 gal (102,000 L)
QC7I Triple - MH

2

2

QC7I Triple - TO

Cartridge Flow Rate Capacity

MC 5.0 gpm (18.9 lpm) 27,000 gal (102,000 L)

2

MC

MH

2

5.0 gpm (18.9 lpm) 27,000 gal (102,000 L)

5.0 gpm (18.9 lpm) 27,000 gal (102,000 L)

TO 4.5 gpm (56.7 lpm) 90,000 gal (340,650 L)
QC7I Triple - CV CV 5.0 gpm (18.9 lpm) 22,500 gal (85,170 L)
QC7I Triple - XCV
QC7I Triple - XC XC 5.0 gpm (18.9 lpm) 36,000 gal (136,260 L)
QC7I Triple - XC

2

QC7I Triple - 7CB5

XCV 5.0 gpm (18.9 lpm) 30,000 gal (113,550 L)

2

XC

5.0 gpm (18.9 lpm) 36,000 gal (136,260 L)

7CB5 7.5 gpm (28.2 lpm) 30,000 gal (113,550 L)
QC7I Triple - 7CB5-K 7CB5-K 7.5 gpm (28.2 lpm) 30,000 gal (113,550 L)
QC7I Triple - 7CB5-S

7CB5-S 7.5 gpm (28.2 lpm) 30,000 gal (113,550 L)

Replacement

Combined Model Name

QC7I Quad - MC MC 6.6 gpm (25 lpm) 36,000 gal (136,000 L)
QC7I Quad - MC
QC7I Quad - MH MH 6.6 gpm (25 lpm) 36,000 gal (136,000 L)
QC7I Quad - MH

2

2

Cartridge Flow Rate Capacity

2

MC

MH

2

6.6 gpm (25 lpm) 36,000 gal (136,000 L)

6.6 gpm (25 lpm) 36,000 gal (136,000 L)
QC7I Quad - TO TO 6.0 gpm (22.4 lpm) 120,000 gal (454,200 L)
QC7I Quad - CV CV 6.6 gpm (25 lpm) 30,000 gal (113,550 L)
QC7I Quad - XCV XCV 6.6 gpm (25 lpm) 40,000 gal (151,400 L)
QC7I Quad - XC XC 6.6 gpm (25 lpm) 48,000 gal (181,680 L)
QC7I Quad - XC

2

XC

2

6.6 gpm (25 lpm) 48,000 gal (181,680 L)
QC7I Quad - 7CB5 7CB5 10.0 gpm (37.6 lpm) 40,000 gal (151,400 L)
QC7I Quad - 7CB5-K 7CB5-K 10.0 gpm (37.6 lpm) 40,000 gal (151,400 L)
QC7I Quad - 7CB5-S 7CB5-S 10.0 gpm (37.6 lpm) 40,000 gal (151,400 L)

* For individual cartridge specifications, refer to cartridge literature.

Temperature: 35-100°F (2-38°C)
Pressure: 10 - 125 psi (0.7 - 8.6 bar), non-shock

For cold water use only.

Figure 5 – Single System

Figure 6 – Twin System

INSTALLATION

1. Use the predrilled mounting holes in the manifold bracket as guides. Mark and drill anchor holes.
Mount securely. See Figures 5-8.

2. Shut off power to machine.

3. Connect outlet port of QC7I unit to equipment served. Always use a NSF approved pipe dope
or Teflon tape at all connections. Use a backup wrench on all fittings while connecting to avoid
excessive stress on the system components.

Note: If the optional E-Series Filter is used, install a manual shut-off valve leading to the system
for servicing.

4. Connect minimum 3/8” water line to inlet side of QC7I singles. Use minimum 1/2” line for other
systems.

5. The cross fitting has a flushing valve installed on the bottom. Connect tubing to flushing valve and
run to drain.

Note: Some municipal plumbing codes and good sanitary practices require an air gap at the drain
termination point.

6. Install the cartridge(s) into the QC7I head (s) following directions on the cartridge label or as shown
in the Cartridge Change illustrations.

7. Turn on water to filter and check for leaks.

8. Flush the cartridge by running water through at full force for five minutes. This will set the filtering
media and purge air and fines, insuring maximum filter life.

9. After flushing, close the flushing valve, turn on power to equipment and plug the LPA (if so
equipped) into the electrical outlet. See illustrations.

Figure 7 – Triple System

Figure 8 – Quad System

Check for compliance with state and local laws
and regulations. Do not use with water that is
microbiologically unsafe or of unknown quality without
adequate disinfection before or after the system. Systems
certified for cyst reduction may be used on disinfected
waters that may contain filterable cysts.

Low Inlet
Pressure

Adequate Inlet

Pressure

Low Outlet

Pressure

Adequate Outlet

Pressure

CARTRIDGE CHANGE DETERMINATION

Replace cartridges when capacity is reached, or when flow becomes inadequate, but at least annually. All cartridges on multiple cartridge systems should
be changed at the same time. The Everpure Pressure Gauge or Everguard Low Pressure Alarm provides a quick and simple means of determining when the
filter cartridge(s) should be changed. Installed on the outlet port of the filter, the gauge or Everguard LPA can be used to measure both dynamic (flowing) and
static (line) pressure. The cartridge(s) should be changed when the pressure gauge needle is in the red area while equipment is in operation, and yet the
needle shows adequate line pressure between cycles. Observe the needle during the next equipment on cycle. If the needle registers adequate pressure, it
can be assumed that the temporary low-pressure condition was caused by a brief power failure or other incoming pressure disruption.

FLUSHING

For maximum life, all carbon filter cartridges must be flushed for five minutes at full flow before use. ALL NEW CARTRIDGES MUST BE FLUSHED AFTER EACH
CARTRIDGE CHANGE BEFORE BEING PUT INTO SERVICE!

If the cartridges are new, have been properly flushed and both needle and follower register inadequate pressure, or the LPA is sounding, you may be experiencing inadequate
water pressure or some restriction may exist in the inlet water line. In either case, the incoming water pressure must be improved to receive optimum filter life.

COMPLETE CARTRIDGE CHANGE INSTRUCTIONS CAN BE FOUND ON THE FILTER CARTRIDGE LABEL.

Not for residential use. For food service applications only.

PRESSURE GAUGES

CARTRIDGE CHANGE PROCEDURE

Everpu re Carbon Filt er Cartridg e
Change

1. Shut o ff power to equipment. Shut
off inle t water ahead of sys tem.

2. Open fl ushing valve to relieve
pressure.

3. Hold h ead firmly a nd push upward.
Turn cart ridge to le ft until it stop s.

4. Pull cartridge downward and out of
head.

5. Hold h ead firmly. A lign cartridge
lug with la bel. Insert new cartri dge
firmly int o head.

6. Turn car tridge right 90˚ until
rotation stop s.

7. Repe at steps 3 -6 for remaining
cartridges.

Flushing

8. Wit h flushing valve fully o pen, open
inlet water at full fo rce for five
minutes . Close flu shing valve.

9. Turn on power to equipment

For installations in Massachusetts, the Commonwealth of Massachusetts Plumbing Code 248 CMR shall be adhered to. Consult your licensed
plumber for installation of the system. This system and its installation must comply with state and local regulations.

REPLACEMENT PARTS

Contact your local Everpure dealer for filter cartridges or system
replacement parts.

Description Part Number

Outlet pressure gauge EV3114-09
Inlet pressure gauge (quad system only)
Inlet valve (twin, triple & quad) EV3114-07
Flushing valve EV3114-07

EV3114-09

System Tested and Certified by NSF International against
NSF/ANSI Standards 42 and 53 for the reduction of:

Standard No. 42 —
Aesthetic Effects

Chemical Reduction

Taste and Odor
Chlorine

Mechanical Filtration

Particulate Class I: 99.2% reduction of particles one-half
micron and larger in size (MC, MC

Standard No. 53 —
Health Effects

Mechanical Filtration (MC, MC2, MH, MH2, XC, XC2 Only)

Turbidity
Cyst
Asbestos

2

, XC, XC2 only)

LIMITED WARRANTY

COMMERCIAL WATER TREATMENT EQUIPMENT

You have just purchased one of the finest water treatment units made. As an expression of our confidence in Everpure products, this product is warranted against defects in
material and workmanship to the original end-user when installed in accordance with Everpure specifications. The warranty period commences from the date of purchase
and is administered as follows:

For a period of ONE YEAR Replaceable elements (i.e., filter & water treatment cartridges)*

For a period of FIVE YEARS The entire system (excluding replaceable elements)

*This is for material & workmanship, not filter or water treatment cartridge life.

The unit must be used in operating conditions that conform to Everpure’s recommended design guidelines. This warranty will not apply if the unit has been modified, repaired
or altered by someone not authorized by Everpure.

If a part described above is found defective within the specified period, you should notify Everpure technical service at the phone number listed below. Any part
found defective within the terms of this warranty will be repaired or replaced (at Everpure’s discretion) by your local dealer or Everpure technical service. You
pay only freight from our factory and local dealer charges. Any repaired or replaced warranty item will be incorporated under the original warranty terms of the
existing system.

We are not responsible for damage caused by accident, fire, flood, freezing, Act of God, misuse, misapplication, neglect, oxidizing agents (such as chlorine, ozone,
chloramines and other related components), alteration, installation or operation contrary to our printed instructions, or by the use of accessories or components which do not
meet Everpure’s specifications. Refer to the specifications section in the Installation and Operating manual for approved application parameters.

Our product performance specifications are furnished with each water treatment unit. TO THE EXTENT PERMITTED BY LAW, EVERPURE DISCLAIMS ALL IMPLIED WARRANTIES,
INCLUDING WITHOUT LIMITATION WARRANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR PURPOSE; TO THE EXTENT REQUIRED BY LAW, ANY SUCH IMPLIED
WARRANTIES ARE LIMITED IN DURATION TO THE PERIOD SPECIFIED ABOVE FOR THE ENTIRE WATER TREATMENT UNIT. As a manufacturer, we do not know the characteristics
of your water supply or the purpose for which you are purchasing this product. The quality of water supplies may vary seasonally or over a period of time, and your water
usage rate may vary as well. Water characteristics can also differ considerably if this product is moved to a new location. For these reasons, we assume no liability for the
determination of the proper equipment necessary to meet your requirements, and we do not authorize others to assume such obligations for us. Further, we assume no
liability and extend no warranties, express or implied, for the use of this product with a non-potable water source or a water source which does not meet the conditions for
use described in the owner’s guide or performance data sheet for this product. OUR OBLIGATIONS UNDER THIS WARRANTY ARE LIMITED TO THE REPAIR OR REPLACEMENT
(AT EVERPURE’S DISCRETION) OF THE FAILED PARTS OF THE WATER TREATMENT UNIT, AND WE ASSUME NO LIABILITY WHATSOEVER FOR DIRECT, INDIRECT, INCIDENTAL,
CONSEQUENTIAL, SPECIAL, GENERAL OR OTHER DAMAGES.

Some states do not allow the exclusion of implied warranties or limitations on how long an implied warranty lasts, so the above limitation may not apply to you. Similarly,
some states do not allow the exclusion of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific
legal rights, and you may also have other rights which vary from state to state. Consult your telephone directory for your local independently operated Everpure dealer, or
write Everpure for warranty and service information.

For sales, replacement components, and service, contact your Everpure dealer or:
Everpure, LLC: 1040 Muirfield Drive • Hanover Park, Illinois 60133 • 800.323.7873
In Europe: Toekomstlaan 30 • B-2200 Herentals, Belguim
In Japan: Hashimoto MN Bldg. 7F • 3-25-1 Hashimoto Sagamihara-Shi • Kanagawa 229-1103, Japan

Printed in U.S.A. EV3024-87D DE05

Technical Service

800.942.1153
rpure.com

www.eve