EverFocus FH 7517 EBL, FH 7519 EBL Installation & Operation Manual

INSTALLATION / OPERATION

FH 7517 EBL

43cm (17") TFT Monitor with LED Backlight

FH 7519 EBL

48cm (19") TFT Monitor with LED Backlight

FH7517EBL / FH7519EBL Installation / Operation 2 of 12

Safety warnings

Safety warnings

To avoid any damage, please consider the following safety warnings:
Never place the device near to heaters, furnaces, other heat sources or under direct solar irradiation.

Operate the device only in locations providing the tolerable operating temperature range 0°C~40°C.

Make sure that the device‘s ventilation slots are not covered or sheeted.
For cleaning, make sure the device is plugged off and only use a damp cloth without acid detergent. Do NOT use

cleaning fluids based on alcohol, methylated spirit, or ammonia. The glass plate has a hard surface coating to prevent
scratches. However, the use of strong chemical cleaning agents may damage this coating. Use only a mild soap or
detergent and water or specially formulated cleaners made for cleaning glass panels.

Install the device only in dry and dustproof surroundings. Protect the device against any liquid‘s penetration.
Avoid the penetration of any artefacts, e.g. through ventilation slots.
Do not open the monitor yourself. In case of malfunction, contact your local installer or dealer. Unauthorized opening of

the device will annul the warranty claim!

Use only the original external power supply.

WEEE:

FCC:

ATTENTION! This is a class A product which may cause radio interference in a domestic
environment; in this case, the user may be urged to take adequate measures.

The information in this manual was current upon publication. The manufacturer reserves the right to revise and
improve his products. Therefore, all specifications are subject to change without prior notice. Misprints reserved.
Please read this manual carefully before installing and using this unit. Be sure to keep it handy for later reference.

Your EverFocus product is designed and
manufactured with high quality materials and
components which can be recycled and reused.
This symbol means that electrical and electronic
equipment, at their end-of-life, should be disposed
of separately from your household waste.
Please, dispose of this equipment at your local
community waste collection/recycling centre.
In the European Union there are separate
collection systems for used electrical and
electronic product.
Please, help us to conserve the environment we
live in!

Ihr EverFocus Produkt wurde entwickelt und
hergestellt mit qualitativ hochwertigen Materialien
und Komponenten, die recycelt und wieder
verwendet werden können.
Dieses Symbol bedeutet, dass elektrische und
elektronische Geräte am Ende ihrer Nutzungsdauer
vom Hausmüll getrennt entsorgt werden sollen.
Bitte entsorgen Sie dieses Gerät bei Ihrer örtlichen
kommunalen Sammelstelle oder im Recycling
Centre.
Helfen Sie uns bitte, die Umwelt zu erhalten, in der
wir leben!

This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired
operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generation, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:

 Reorient or relocate the receiving antenna.
 Increase the separation between the equipment and

receiver.

 Connect the equipment to an outlet on a circuit different

from that to which the receiver is connected.

 Consult the dealer or an experienced radio/TV technician

for help.

FH7517EBL / FH7519EBL Installation / Operation 3 of 12

CONTENT

Safety warnings ....................................................................................................................................... 2

1 INTRODUCTION................................................................................................................................... 4

2 MAIN FEATURES ................................................................................................................................. 4

3 PACKAGE CONTENTS ........................................................................................................................ 4

4 CONNECTORS..................................................................................................................................... 4

5 INSTALLATION .................................................................................................................................... 5

6 FRONT KEYS ....................................................................................................................................... 5

7 SETUP .................................................................................................................................................. 6

7.1 Picture Setup....................................................................................................................... 6

7.2 Sound Setup ....................................................................................................................... 7

7.3 OSD Setup .......................................................................................................................... 7

7.4 Picture-in-Picture Setup ...................................................................................................... 8

7.5 EXIT .................................................................................................................................... 8

8 SPECIFICATIONS ................................................................................................................................ 9

9 DIMENSION DRAWING ..................................................................................................................... 10

10 SUPPORTED DISPLAY MODES ...................................................................................................... 11

FH7517EBL / FH7519EBL Installation / Operation 4 of 12

1 INTRODUCTION

The TFT monitors FH 7517 EBL and FH 7519 EBL are designed for CCTV installations.
The new LED backlight technology provides clear high-contrast images combined with long component
lifetime. This new feature allows also dropping down the power consumption more than 40% compared
to former models.
This monitor series is equipped with newest 4D comb-filter with De-Interlace technology for clear natural
color reproduction.
The different video input types and high display quality allow usage in almost all kinds of CCTV
applications.

2 MAIN FEATURES

 LED backlight illumination
 2 x BNC Composite video input
 2 x BNC Composite video output
 1 x HDMI input
 1 x VGA input
 2 x Audio input, build in speakers
 Newest 4D - Comb - Filter with De-Interlace technology for clear color transitions and suppression of crosscolors
 Integrated 3D noise reduction filter
 Easy multi-language OSD setup
 Picture size and - position setup also for all video input types
 Newest power management technology
 VESA compatible mount (75mm)
 Picture-in-Picture

3 PACKAGE CONTENTS

 TFT Monitor with stand base
 12V DC Adapter / Power cord
 D-Sub 15-pin VGA connector Cable
 User's Guide

4 CONNECTORS

1 2 3 4 5 6 7 8 9

1) DC DC socket for 12VDC power supply

2) HDMI Input: HDMI type A input socket

3) VGA 15-pin standard VGA input socket

4) PC-Audio 3,5 stereo socket for audio output (assigned to VGA IN)

5) AV audio: 2 x RCA audio in socket (assigned to AV1 / AV2)

6) AV1 Input: BNC composite video input, fixed 75 Ohm termination

7) AV1 Output: BNC Loop-Through output for AV1 input

8) AV2 Input: BNC composite video input, automatic 75 Ohm termination, if no load is

connected to AV2 output

9) AV2 Output: BNC Loop-Through output for AV2 input