EverFocus EZN3260, EZN3340, EZN3160 Installation Guide

EZN Plus Series

Outdoor IR Bullet IP Camera

Quick Installation Guide

Copyright © EverFocus Electronics Corp,

Release Date: October, 2012

EZN Plus Series

1
2

3

4 5

6

7

8

9

1. Overview

The EZN Plus Series is a bullet type IP camera designed for outdoor use. The series comes in three

models: EZN3160 Plus / 3260 Plus / 3340 Plus.

Model Name Megapixel WDR

EZN3160 Plus 1.3 MP Yes

EZN3260 Plus 2 MP Yes

EZN3340 Plus 3 MP No

No. Item Name Descriptions

1 TV-Out Connector

2 Focus / Zoom Control

3 Reset Button

4 Lens

5 Micro SD / SDHC Slot

6 IR LEDs

7 Light Sensor

Connects to a handheld test monitor for adjusting camera focus
and zoom.

Press this control to the left or right to adjust camera focus. To
zoom in / out the camera view, press this control up or down.

Resets all configurations to the factory default settings.

Varifocal lens.

For inserting a micro SD / SDHC card.

44 IR LEDs for infrared illumination in night vision applications.

Detects lights.

Remove the cover for adjusting camera focus and zoom /

8 Camera Cover

inserting a micro SD card or connecting to a handheld test
monitor.

9 Sunshield

Protect the camera from the direct rays of the sun.

1

EZN Plus Series

2

Alarm Input / Output
Audio Input (Pink)

Audio Output (Green)

12V DC Input

4 3 2 1

System Requirements

Before installing, please check that your computer meets the following system requirements.

• Operating System: Microsoft Windows XP / Vista (32-bit) / 7 (32-bit)

• Microsoft Internet Explorer 7 or above

Packing List

• EZN Plus Series Camera x 1 • 4-Pin Terminal Block x 1

• Quick Mounting Ring x 1 • Software CD x 1

• RJ-45 Connector x 1 • Quick Installation Guide x 1

• Mounting Kit x 1

- Long Screw x 4 (for attaching the Quick Mounting Ring to the mounting surface)

- Short Screw x 4 (for connecting the camera base to the quick Mount Ring)

- Screw Anchor x 4 (in conjunction with Long Screw)

- Hexagon Key x 1 (for adjusting the camera position)

- Hexagon Wrench x 1 (for removing the sunshield)

- Torx Wrench x 1 (for removing the lock tab)

- Mounting Template x 1

Note: Contact the shipper if any items appear to have been damaged in the shipping process. If any

items are missing, notify your EverFocus Electronics Corp. Sales Representative or Customer Service

Branch. Please also keep the shipping carton for possible future use.

2. 4-Pin Data Cable

The 4-Pin Data Cable provides connections for power, audio input / output and alarm input / output.

The wires are illustrated and defined below. Note that microphones with external power supplies

are required.

Pin Assignment for Alarm Input / Output

Pin 1: Alarm GND

Pin 2: Alarm In

Pin3: Alarm Out-

Pin4: Alarm Out+

EZN Plus Series

3

Quick-Mounting Ring

Long Screws

Camera Base Quick-Mounting Ring

Cables

3. Installation

This installation guide provides the basic instructions on installing an EZN Plus bullet IP camera. For

details, please refer to the User’s Manual in the software CD.

3.1 Mounting and Wiring

Follow the steps below for mounting and wiring the camera.

1. Before screwing the camera to the wall, drill four holes on the wall according to the

hole-positions on the supplied Quick-Mounting Ring. If you wish to run the wires into the

wall, drill another hole in the middle of the circular area within the Quick-Mounting Ring.

2. Push the four supplied anchors into the four holes on the wall.

3. Place the Quick-Mounting Ring against the anchoring surface so that the holes line up.

Screw the Quick-Mounting Ring to the wall using the supplied Long Screws.

4. Screw the camera body to the Quick-Mounting Ring using the supplied four Short Screws.
a. If you want to wire the cables from the side of the camera base: