Page 1
EZA2580 eZ.HD Series
5MP Dual Power IP66 IR Bullet Camera
User’s Manual
Copyright © EverFocus Electronics Corp.
Release Date: May, 2019
All the images including product pictures or screen shots in this document are for example
only. The images may vary depending on the product and software version. Information
contained in this document is subject to change without notice.
EverFocus Taiwan:
2F., No.12, Ln. 270, Sec. 3, Beishen Rd., Shenkeng Dist., New Taipei City 222, Taiwan
TEL: +886 2 2662 2338 FAX: +886 2 2662 3632 www.everfocus.com.tw
Page 2
128mm / 5"
280mm /
11"
91.5mm /3.6"
84mm / 3.31"
1. Introduction
Equipped with a Sony STARVIS CMOS sensor, the EZA2580 deliver 5MP image
quality. The model provides 2.8-12mm lens with ICR. Featured with True Wide
Dynamic Range (T-WDR), the camera can provide clear images even under
backlight circumstances where intensity of illumination can vary excessively.
The EZA2580 supports dual power (12VDC / 24VAC, depends on model) and
supports both NTSC and PAL scanning systems.
1.1 Packing List
Camera x 1
Mounting Sticker x 1
L-Type Wrench x 1
Screw & Screw Anchor x 3
User Manual x 1
1.2 Features
5MP Sony STARVIS CMOS sensor, delivering amazing high sensitivity
Varifocal 2.8-12mm with ICR to capture the desired field of view
Extended IR range of up to 40m / 131ft. with 4 LEDs (depends on scene
IR reflectivity)
T-WDR to improve the visibility under high contrast scene
3-Axis rotation design allows wall or ceiling mounting
IP66-rated with metal housing
Supports dual power (12VDC / 24VAC, depends on model)
Supports UTC function: Control camera OSD settings directly from DVR
end
1.3 Dimensions
1
Page 3
2
BAE3201
12VDC
or 24
VAC
Power Cable
Video Output Cable
(
BNC,
75
Ohm
)
Mounting
Surface
Screws Screw Anchors
Camera Base
1.4 Optional Accessory
Color: White
Size (Φ x H): 138 x 54mm / 5.43” x 2.16”
Weight: 700g / 1.87
Material: Metal
1.5 Cable Description
2. Installation
1. Stick the supplied Mounting Sticker to the surface to mark the 3 screw
positions. Drill 3 holes on the surface and insert the supplied 3 Screw
Anchors into the screw holes. If you want to run the cable through the
surface, drill a hole within the 3 screw area.
2. To mount the camera to the surface, screw the Camera Base to the surface
using the supplied 3 Screws.
3. Connect the Power Cable to a 12VDC / 24VAC power source. Connect the
Video Output Cable to a monitor or DVR.
4. You can use the Joystick on the cable to configure camera OSD settings or
switch to different video formats. Remove the Protection Cap from the
Joystick before using it.
Page 4
3
UP
DN
Z
OO
M
F
O
C
U
S
Tilt Screw
Rotate Screw
Switching Video Format:
• Push the joystick up for 5 sec. to switch to
AHD.
• Push the joystick right for 5 sec. to switch to
TVI.
• Push the joystick down for 5 sec. to switch to
CVI.
• Push the joystick left for 5 sec. to switch to
CVBS.
Configuring OSD Settings:
• Push the Joystick up / down to select among
menu items.
• Push the Joystick left / right to adjust the level
of the selected item.
• Press the Joystick to enter the submenu or
exit the OSD Setup Menu.
5. For the first time installation, check whether the camera is properly
focused. If not, you can manually adjust camera Zoom or Focus using the
supplied L-Type Wrench. You can find the Zoom and Focus nuts on the
bottom of the camera.
6. You can optionally adjust camera angles. To do so, loosen the Tilt Screw or
Rotate Screw on the bracket using the supplied L-Type Wrench to adjust
camera angles. After adjusting camera angles, tightly screw back the
Tilt/Rotate screws.
Page 5
4
No
Main
Sub Menu
Sub Menu / Function
Level
0-10
YEL, CYN, GRN, MAG, RED, BLU, BLK,
WHT
Off
Brightness
0-20
Auto
Mode
Normal / Deblur
1/30, 1/60, 1/120, 1/250,
1/30000
Flicker
Sens-Up
X2, x4, x8, x16, x32, Off
AGC
0-10
Level
0-20
YEL, CYN, GRN, MAG, RED, BLU, BLK,
WHT
H-POS
0-26
V-POS
0-32
H-SIZE
0-26
V-SIZE
0-32
WDR Mode
Frame, Line
Window Zone
0-3
Window Use
On, Off
H-POS
0-2608
V-POS
0-1960
H-SIZE
0-2608
V-SIZE
0-1960
Window Zone
0-3
Window Use
On, Off
POS0-X
0-721
POS0-Y
0-535
POS1-X
0-721
POS1-Y
0-535
POS2-X
0-721
POS2-Y
0-535
POS3-X
0-721
POS3-Y
0-535
Off
Weight
High, Middle, Low
Off
IR LED
Adaptive, Off
Anti-Sat.
0-20
D>N Thres
0-20
N>D Thres
0-20
Delay
High, Middle, Low
Color
B/W
IR LED
Adaptive, Off
3. Configuration in the OSD Menu
1 Edge Det
2 Exposure
On
Shutter
HLC
BLC
Color
Manual Speed
Color
1/500, 1/1000, 1/2000,
1/4000, 1/8000, 1/15000,
3 Backlight
WDR
4 Day/Night Mode
Box
ROI Mode
Polygon
Auto
Page 6
5
Anti-Sat.
0-20
D>N Thres
0-20
N>D Thres
0-20
Delay
High, Middle, Low
IR LED
Adaptive, Off
Anti-Sat.
0-20
Extern SW
High, Low
D>N Thres
0-20
N>D Thres
0-20
Delay
High, Middle, Low
Auto
Autoext
Preset
C-Temp
3000K, 5000K, 8000K
R-Gain
0-20
B-Gain
0-20
Color Gain
0-20
6
DNR
High, Middle, Low, Off
Sharpness
0-10
Gamma
0.45, 0.55, 0.65, 0.75
Mirror
On, Off
Flip
On, Off
D-Zoom
1.0X-16X
ACE
High, Middle, Low, Off
Mode
Auto, Manual
Level
High, Middle, Low
Off
On
Weight
0%-100%
Off
Zone Num
0-15
Zone Disp
On, Off
H-POS
0-80
V-POS
0-61
H-Size
0-80
V-Size
0-61
Y Level
0-20
CB Level
0-20
CR Level
0-20
Trans
0-3
Off
Zone Num
0-7
Zone Disp
On, Off
POS0-X
0-162
POS0-Y
0-122
POS1-X
0-162
POS1-Y
0-122
POS2-X
0-162
POS2-Y
0-122
POS3-X
0-162
POS3-Y
0-122
Y Level
0-20
Extern
5 Color
AWB
Defog
Shading
Manual
On
7 Image
Privacy
Box
On
Polygon On
Page 7
6
CB Level
0-20
CR Level
0-20
Trans
0-3
Off
Window Use
0-3
Window Zone
On, Off
Det H-POS
0-80
Det V-POS
0-60
Det H-Size
0-80
Det V-Size
0-60
Sensitivity
0-10
Motion OSD
On, Off
Text Alarm
On, Off
Signal Out
On, Off
Off
4K/15fps, 4MP/30fps, 1080p/30fps,
5MP/12.5fps, 5MP/20fps, 4MP/15fps
Freq
60Hz, 50Hz
Analog Mode
AHD, TVI, CVI, CVBS
Confirm
Yes
Return
Exit
Full
Comp
User
Offset
0-32
Color Space
HD-CbCr, SD-CbCr, YUV
Audio Mic
Not supported
Color Bar
On, Off
Language
ENG, CHN, CHN(S), JPN, KOR, POR, ESP
Left-Down
Right-Up
Off
Reset
On
10
Exit
Det Window
8 Motion
9 System
On
Frame Rate
Output
Image Range
Cam Title
Loading...