EverFocus EZ610 User Manual

EverFocus

Installation / Operation Instructions

EEZZ661100

LLooww LLiigghhtt IInnlliinnee
IIPP6666 BBuulllleett CCaam

meerraa

EVERFOCUS ELECTRONICS CORPORATION

P/N: 4605XZ0610001AR

Operation Instruction

© 2010 EverFocus Electronics Corp

Please read this manual first for correct installation and operation. This manual should be retained for
future reference. The information in this manual was current when published. The manufacturer reserves
the right to revise and improve its products. All specifications are therefore subject to change without
notice.

All rights reserved. No part of the contents of this manual may be reproduced or transmitted in
any form or by any means without written permission of the EverFocus Electronics Corporation.

2

Precautions

1. Do not install the camera near electric or magnetic fields.
Install the camera away from TV/radio transmitters, magnets, electric motors, transformers and
audio speakers since the electromagnetic fields generated from these devices may distort the
video image.

2. Never disassemble the camera beyond the recommendations in this manual nor introduce
materials other than those recommended herein.
Improper disassembly or introduction of corrosive materials may result in equipment failure or
other damage.

3. Try and avoid facing the camera toward the sun.
In some circumstances, direct sunlight or may cause permanent damage to the sensor and/or
internal circuits.

4. Keep the power cord away from water and other liquids and never touch the power cord with
wet hands.
Touching a wet power cord with hands or touching the power cord with wet hands may result in
electric shock.

5. Never install the camera in areas exposed to oil, gas or solvents.
Oil, gas or solvents may result in equipment failure, electric shock or, in extreme cases, fire.

6. Cleaning
Do not touch the surface of the sensor directly with the hands. Use a damp soft cloth to remove
any dirt from the camera body. Use lens tissue or a cotton tipped applicator and ethanol to clean
the sensor and the camera lens. Please do not use complex solvents, corrosive or abrasive
agents for cleaning.

7. Do not operate the camera beyond the specified temperature, humidity or power source
ratings.
Use the camera at temperatures within -40°C ~ 50°C (-40°F~122°F) and in an IP66 complaint
environment; this device is not rated as submersible. The input power source is 12VDC/24VAC.

3

Federal Communication Commission Interference Statement

y

This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one of the
following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.

- Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for

compliance could void the user's authority to operate this equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.

ATTENTION! This is a class A product which may cause radio interference in a domestic environment; in

this case, the user ma

be urged to take adequate measures.

This Product is RoHS compliant.

WEE

Your EverFocus product is designed and manufactured with high quality materials and
components which can be recycled and reused.
This symbol means that electrical and electronic equipment, at their end-of-life, should
be disposed of separately from your household waste.
Please, dispose of this equipment at your local community waste collection/recycling
centre.
In the European Union there are separate collection systems for used electrical and
electronic product.

The information in this manual was current upon publication. The manufacturer reserves the right to revise and improve
his products. Therefore, all specifications are subject to change without prior notice. Misprints reserved.
Please read this manual carefully before installing and using this unit. Be sure to keep it handy for later reference.

4

Table of Contents

1 Product Overview..............................................................................................................................................7

1.1 Features..........................................................................................................................................................7

1.2 Accessory Parts List........................................................................................................................................8

1.3 Specifications..................................................................................................................................................9

1.4 Dimensions....................................................................................................................................................10

1.5 Camera Component Description...................................................................................................................11

1.6 Related Products...........................................................................................................................................11

2 Installation.......................................................................................................................................................12

2.1 Wiring and Mounting............................................................................................. .........................................12

2.2 Adjust Camera Position.................................................................................................................................14

3 OSD Menu Setup.............................................................................................................................................16

3.1 Control Key General Operation Guide...........................................................................................................16

3.2 RS485 ID & Baud Rate Setting.....................................................................................................................17

3.3 OSD Menu Setup..........................................................................................................................................18

3.3.1 OSD Menu Tree .....................................................................................................................................18

3.3.2 LENS ......................................................................................................................................................20

3.3.3 EXPOSURE............................................................................................................................................20

3.3.3.1 SHUTTER.............................................................. ....................................................................20

3.3.3.2 AGC (Auto Gain Control – basic low light signal amplification)........... ............................................20

3.3.3.3 SENS-UP..................................... ................................................................................ ..............20

3.3.3.4 BLC/HSBLC ...................................... ........................................ Error! Bookmark not defined.

3.3.3.5 D-WDR ............................................................................................... .......................................22

3.3.4 WHITE BALANCE CONTROL................................................................................................................22

3.3.5 DAY NIGHT............................................................................................................................................23

3.3.6 3DNR......................................................................................................................................................24

3.3.7 SPECIAL ................................................................................................................................................25

3.3.7.1 CAM TITLE.......................................................................................... .......................................25

3.3.7.2 D-EFFECT .............. ...................................................... .............................................................26

3.3.7.3 FREEZE............................................................... ...................................................... ................26

3.3.7.4 MIRROR ........................................... ................................................................................ .........26

3.3.7.5 D-ZOOM ..................................................................... ...............................................................26

3.3.7.6 GAMMA ..................................... ...................................................... ..........................................26

3.3.7.7 NEG. IMAGE..................................... ...................................................... ...................................26

3.3.7.8 RETURN....................................................... ...................................................... .......................27

3.3.7.9 MOTION............................ ................................................................................ .........................27

3.3.7.10 PRIVACY ............ ................................................................................ .....................................27

3.3.7.11 SYNC............................................ ...................................................... .....................................28

3.3.7.12 LANGUAGE........................................................................... ...................................................28

3.3.7.13 RETURN ........................................................................................................................... .......28

3.3.8 ADJUST..................................................................................................................................................28

3.3.8.1 SHARPNESS .............................................................................................................................28

3.3.8.2 BLUE .................................................. .......................................................................................28

3.3.8.3 RED................................................ ...........................................................................................28

3.3.9 RESET....................................................................................................................................................29

3.3.9.1 FACTORY RESET...................... ................................................................................................29

3.3.9.2 EXIT........................................... ...................................................... ..........................................29

5

4 RS-485 Remote Control..................................................................................................................................30

4.1 Remote control with EKB-500 keyboard........................................................................................................30

4.1.1 RS - 485 Wiring ......................................................................................................................................30

4.1.2 OSD Menu Setting by Keyboard ............................................................................................................30

4.1.3 Lens Adjustment by Keyboard................................................................................................................31

4.2 Remote Control with EverFocus DVR...........................................................................................................31

4.2.1 RS-485 Wiring ........................................................................................................................................31

4.2.2 Camera Operation and Setup by DVR...................................................................................................31

6

r

Chapte

1 PRODUCT O VERVIEW

Amazing color low light sensitivity of 0.05 lux before the added benefits of advanced DSP
technology, delivered by a 1/3” Sony Super HAD II sensor, is just the beginning with the new
EverFocus EZ610. Get color without compromise: 560TVL resolution, your choice of full motion
color or true day/night images in low light without ghosting, plus Digital Wide Dynamic Range to
handle the most challenging of bright or unbalanced scene lighting conditions. Easy to mount
and install, the camera includes a speedy-mount ring, designed to fit a standard 4” electrical box,
for convenient and reliable wall or ceiling mounting; just attach the speedy-mount ring to the
mounting surface and the camera base plate quickly attaches to the ring. A removeable insert in
the ring provides for an on-demand slot for surface wire access. Spin off the base plate, and the
EZ610 mates with any standard 1” conduit thread. The E-Z Lock ring at the base is designed with
sure-grip tabs to firmly clamp the camera to the base plate, plus a set screw in the base provides
added security. Vandal resistant, IP66, with motorized varifocal auto iris lens, dual voltage
operation and a full suite of OSD Menu and DSP functions controllable at the camera or remotely
via RS-485 (3D-DNR to save DVR HDD space, privacy masking, 32X digital zoom, mirroring and
rotation, 256X sens-up to a max of .0002 lux, and much more) this is the camera you have been
waiting for, and might be the only camera you’ll ever need.

1

1.1 Features

• Super HAD II sensor at 0.05 lux has 5X better native light sensitivity before DSP low light

boost

• Color without compromise: your choice of full motion color or true day/night images in low

light without ghosting

• True Day/Night with ICR module (field selectable, if desired)

• Starlight super high sensitivity of 0.0002 Lux/F=1.2 is achieved through a sensitivity

increase setting of up to 256x

• Motorized varifocal auto iris lens – choose 2.8-10mm or 9-22mm focal range

• Digital Wide Dynamic Range expansion to deliver properly exposed images despite bright

light sources, deep shadows and/or unbalanced lighting in the same scene

• Provides 3D-Noise Reduction to improve picture clarity while enabling DVRs to improve disk

storage utilization

• Flexible mounting and positioning – speedy-mount ring also fits a 4” round electrical box; or

remove base to mate with 1” conduit

• E-Z Lock ring at the base is designed with easy to grip tabs to firmly clamp the camera in

place, plus a set screw in the base for added security.

• Easy to use OSD setup menu with local or RS-485 remote control (from a DVR or keyboard)

• Motion detection for 4 configurable zones

• Privacy mask function for 8 configurable zones

• Provides digital zoom up to 32x

• Easy bottom access to video test point and lens/OSD menu controls inside a weatherproof

cover

• IP66 weather resistant

• Dual voltage (12VDC/24VAC) with line lock to AC supply

7

1.2 Accessory Parts List

Please be careful when you unpack the box and the electronic device inside. Check and

make sure that you have all the items listed below inside the original box:

• Camera Unit x 1

• Speedy Mount Ring x 1

• Surface Wire Slot Filler x 1

• Operation Manual x 1

• Video Test Cable x 1

• Power Supply Pigtail x 1

• Mounting Kit x 1

Mounting kit includes:

• Long Screws x 4 (for attaching EZ Mount Ring to mounting surface)

• Short Screws x 4 (for connecting camera base to EZ Mount Ring)

• Expanding Anchors x 4

• Hex key x 1 (for adjusting camera)

• Hexagon wrench x 1 (for adjusting sunshield and set screw in base)

• Mounting Template x 1

Note: If an item appears to have been damaged in shipment, replace it properly in its carton

and notify the shipper. If any items are missing, notify your EverFocus Electronics Corp.
Sales Representative or Customer Service. The shipping carton is the safest container in
which the unit may be transported. Save it for possible future use.

8

1.3 Specifications

Model

Pickup Device
Video Format

Picture Elements

Horizontal Resolution

Sensitivity

S/N Ratio Over 52dB (AGC off)
Electronic Shutter 1/50(1/60) ~1/100,000
Video Output Main Output BNC 1.0V p-p 75Ω,

Gamma Correction

Lens Type

Back Light Compensation

Auto Gain Control

White Balance

Sync. Mode

Day & Night

OSD menu

3D-DNR

Digital WDR

Digital Slow Shutter

Mirror

Digital Zoom

Motion Detection

Privacy Mask

RS-485

Power Source

Power Consumption 12VDC: 2,5W / 5W max with heater

Operating Temperature

Weatherproof IP66 rated

Vandal Resistant Yes

Dimensions

Weight 1250 g / 2.275 lbs.
Mounting Pattern Speedy-Mount Ring also mates with 4” round electrical box; base swivel is 1” NPT – remove

Certifications

EZ610

1/3" SONY Super HAD II CCD

NTSC, PAL (by model)

768 x 494(NTSC)/ 752 x 582 (PAL)

560 TVL

0.05Lux/F=1.2 (AGC ON); 0.0002Lux/F=1.2 (Sens-up 256x)

Local test output, cable provided.

0.45

DC Iris Varifocal: focal length 2.8-10mm (MVB) or 9-22mm (MV2)

OFF/BLC/HS BLC Selectable

Low/Middle/High Selectable

ATW/AWB/AWC/Manual/Indoor/Outdoor Selectable

Internal / Line lock (24 VAC only)

Color/Auto/BW/EXT

Multiple functions

Off/On switchable

Off / Outdoor / Indoor

Sens-Up up to 256X

Off/Mirror/V-Flip/Rotate Selectable

Off/On selectable up to 32X

Off/On for 4 selectable zones

Off/On for 8 selectable zones

2 wire simplex; address 1~99; 1200-9600 baud; EverFocus or Pelco-D protocol self detecting

12VDC/24VAC

24VAC: 3 W / 6 W max. with heater

-40°C~50°C ; -40°F~122°F (built-in thermostat controlled heater)

Total Length 316.2mm/12.49 in.
Body/sunshield 81.5mm/3.21 in. high
Base 105.1mm/4.15 in. diameter

base plate for coupling to standard conduit fittings.

CE / FCC

9

1.4 Dimensions

Camera Base Camera Body

Front view of EZ610

10