EverFocus EMV800FHD Installation Guide
EMV1200 FHD / EMV800 FHD
12CH/8CH Hybrid Mobile DVR
Quick Installation Guide
Copyright © EverFocus Electronics Corp.
Release Date: May, 2018
All the images including product pictures or screen shots in this document are for example only.
The images may vary depending on the product and software version. Information contained in
this document is subject to change without notice.
EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR
Operating System
Windows XP (32-bit) / Win7 (32 and 64-bit)
CPU
Intel Core I3-2100
RAM
2GB
VGA
Intel HD 2000
LAN Speed
10 / 100 / 1000 Mbps (RJ45)
1. EverFocus’ Xfleet fleet management server system.
1. Introduction
The latest EverFocus digital video recorder generation is based on H.264 compression
technology, resulting in enhanced recording capacity and improved network image transmission
speed with high image quality. The EMV800 FHD / EMV1200 FHD can support both of analog
(AHD/TVI/SD) and IP cameras, delivering up to 1080p (analog) and up to 4MP (IP) image quality.
Its comprehensive features along with the embedded 3-axis g-sensor function enable the almost
universal application of this mobile DVR series. It supports various interfaces such as alarm I/O,
three USB ports, one RS-485 and three RS-232 for connecting to devices such as Panic Button or
CAN bus. You can also optionally connect GPS receiver, 3G, 4G and Wi-Fi Antenna to the mobile
DVR. The design of RCA video/audio outputs at front panel makes your installation easy. You
can install one 2.5”hard disk or SSD in the mobile DVR. You can also install one SD Card for
alarm event backup recording. The User Interface has been specially designed to fit mobile
small-sized monitor.
EMV800 FHD / EMV1200 FHD are equipped with anti-shock and anti-vibration housing. The
aviation M12 connectors are also equipped. The power supply supports voltage regulator, and
delay on/off. In addition, the mobile DVRs are SAE-J1455, EN50155, E-Mark, CE and FCC
certified.
You can use EverFocus Mobile Applications, MobileFocus, to remotely view the camera streams
from the mobile DVR through your handheld devices; or use EverFocus Xfleet system for remote
fleet management. You can also use EverFocus EF-Reader to remotely back up recordings from
the HDD/SD card of the mobile DVRs. The mobile DVR series is the ideal solution for your mobile
surveillance needs.
Minimum System Requirements
Before installing, please check that your computer meets the following system requirements.
Web Browser IE11 and later, Firefox 50 and earlier, Chrome 44 and earlier, EF browser
Other Remote
Application
2. EverFocus’ mobile app: MobileFocus (iOS / Android); MobileFocusHD
(iPad).
1
EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR
• 3G Antenna: For using 3G network
3G Antenna
3G Module
• 4G Antenna: For using 4G LTE network (LTE
4G Antennas
4G Module
• Wi-Fi Antenna: For using Wi-Fi function
Wi-Fi Antenna
Wi-Fi Module
• GPS Receiver (LS23035): For using GPS
• Reinforced Data Storage Device (64GB)
Note:
b. Do not dispose of the batteries in a fire as it may explode.
Packing List
• Mobile DVR x 1
• HDD Tray Lock Key x 2 (with 4 screws for screwing HDD. See 2.2 Hard Disk Installation)
• HDD Power Lock Key x 2 (with 4 black screws and 8 spacers for mounting the mobile DVR.
See 2.1.1 Mounting)
• IR Remote Control (with two AAA batteries. See Note 4) x 1
• Power Harness Cable x 1
• Video Cable x 3 (EMV1200 FHD); x2 (EMV800 FHD) (see 3.2 Video Cable / Power-Out
Cable)
• Audio Cable x 1 (see 3.3 Audio Cable)
• D-Sub Cable x 1 (see 3.4 D-Sub Cable)
• Power-Out Cable x 1 (see 3.2 Video Cable / Power-Out Cable)
• CD x 1 (Please see Note 3.)
• Quick Installation Guide x 1
1. Equipment configurations and supplied accessories vary by country. Please consult your
local EverFocus office or agents for more information. Please also keep the shipping
carton for possible future use.
2. Contact the shipper if any items appear to have been damaged in the shipping process.
3. The CD contains the IP Utility software, User Manual and Quick Installation Guide.
4. Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries
according to the instructions.
a. Use only two AAA dry cell batteries.
Optional Accessories
The mobile DVRs feature Wi-Fi/3G/4G. You can optionally connect Wi-Fi/3G/4G module and
antenna to the mobile DVR for networking, or connect a GPS receiver for GPS function.
function
For recordings backup
frequency bands differ among regions)
function
2
Front Panel
4
9
10
7
5
6
8
11
1
3
2
No.
Name
Description
EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR
EMV800 FHD / EMV1200 FHD
Lock to power on the HDD. After locking the HDD Tray Lock (No.2), lock
the HDD Power Lock to power on the HDD. The HDD power indicator
will light in blue to indicate the HDD power is on.
HDD Power
1
Lock
Note: Only when the HDD Power Lock is locked will the system start to
record on the HDD.
2 HDD Tray Lock
Lock or unlock the HDD tray. To power on the HDD, the HDD Power
Lock (No.1) has to be locked.
3 HDD Tray Install a 2.5” HDD (up to 2TB) or SSD (up to 4TB) for recording.
4 USB2.0 Port Three USB2.0 ports for connecting to the USB storage device or mouse.
Insert a SD / SDHC card (up to 128GB) for alarm event backup recording
(see 2.3 SD Card Installation). To see the SD card info, see 6.4.2 SD Card
5 SD Card Slot
in the User’s Manual. To enable the SD card function, see 6.3.1 Alarm in
the User’s Manual. You can also download the Storage Compatibility
Table from the product page (click Download) to see the tested card
brands. www.everfocus.com.tw
Press the button for 3 seconds to switch the RCA / BNC video output
6 Function Key
from call monitor to main monitor; and to switch the VGA video output
from main monitor to call monitor. To switch back the main and call
monitors, press the button for 3 seconds again. Please refer to 3.8
Monitor Connection for more details.
7 IR Receiver Receives data from the infrared remote control.
3
8 System LEDs
2
6
4
1
7
8
9
14
12
11
5
10
13
3
9-12 CH
2
6
4
1
7
8
9
14
12
11
5
10 13
3
Call Monitor
9
(RCA)
EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR
• Alarm: Turns on when the connected alarm I/O is triggered; turns
off when the alarm I/O stops being triggered.
• GPS: Turns on continuously when the mobile DVR is receiving GPS
data.
• System Fail: Turns off when system is acting normally. Turns on
when these events occur: System Clock Error / Fan Fail / Disk
Temperature Over / Disk Fail / Disk Off / Network Loss.
• Heater: Blinks when heater on; off blinking when heater off.
• HD R/W: Blinks when the HDD is reading or writing.
• Power: Turns on continuously when the power is supplied. Blinks
when Battery power error occurs (lower than 9V or higher than 36V)
or 12VDC power supply error.
By default, this port is set to a Call monitor output. Connects to a Call
monitor using a RCA cable.
Note: You can optionally switch this port from Call monitor to Main
monitor. Please refer to 3.8 Monitor Connection for more details.
10 Audio Out
Ethernet Port
11
(WAN)
Rear Panel
EMV800 FHD
RCA audio output for connecting to the speakers. The audio output only
works during playback. Speakers with a (built-in) amplifier and external
power supply are required.
One RJ-45 port for connecting to the network.
EMV1200 FHD
4
EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR
By default, this port is set to a Main monitor output. Connects to a
Connects to the 4G Antenna for using 4G LTE function. Note that
Connects to the Wi-Fi Antenna for using Wi-Fi (5GHz) function.
3 and 4.
D-Sub connector for connecting to the supplied Audio Cable. For
D-Sub connector for connecting to the Alarm I/O, RS-232 (CAN
M12 connector for connecting to IP cameras. For details, please
USB ports for connecting to the USB device. For details, please
M12 connector for connecting to the supplied Video Cable. You
Connector for connecting to the GPS receiver. For details, please
refer to 3.7 GPS Cable.
12VDC Power
A total of 12VDC, 5A power supply to the connected cameras.
Use the supplied Power Harness Cable for connecting to 9 ~
No. Name Description
Main Monitor
1
(VGA)
Main monitor using a VGA cable.
Note: You can optionally switch this port from Main monitor to
Call monitor. Please refer to 3.8 Monitor Connection for more
details.
2 Antenna 1 (3G/4G) Connects to the 3G or 4G Antenna for using 3G / 4G LTE function.
3 Antenna 2 (4G)
Antenna 3 (Wi-Fi)
4
(2.4GHz / 5GHz)
Antenna 4 (Wi-Fi)
5
(5GHz)
6 Audio Input
the 4G function is required to use both Antenna 1 and 2.
Connects to the Wi-Fi Antenna for using Wi-Fi (2.4GHz / 5GHz)
function.
Note that the 5GHz Wi-Fi function is required to use both Antenna
details, please refer to 3.3 Audio Cable. Microphones with a
(built-in) amplifier and external power supply are required.
7 D-Sub Connector
bus) or RS-485 devices (such as analog PTZ cameras). For details,
please refer to 3.4 D-Sub Cable.
8 Ethernet Port (LAN)
9 Call Monitor (CVBS)
10 USB Port
11 Video Input
12 GPS Data Input
13
Outputs
14 DC Power Input
refer to 3.5 Ethernet Cable.
By default, this port is set to a Call monitor output. Connects to a
Call monitor using a BNC cable.
Note: You can optionally switch this port from Call monitor to
Main monitor. Please refer to 3.8 Monitor Connection for more
details.
refer to 3.6 USB Cable.
can then connect analog HD / SD cameras to the Video Cable.
Please refer to 3.2 Video Cable / Power-Out Cable.
Please refer to 3.2 Video Cable / Power-Out Cable.
36VDC power source. For details, please refer to 4 Vehicle
Connection.
5
EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR
Bottom of glove box- horizontal mount
Bottom of passenger seat next to the driver
Underneath bulkhead-horizontal mount
Beside deriver seat-horizontal mount
Note: Do not install the mobile DVR on the floor or on the transmission access hatch. These
Support-Mount
Interface
2. Getting Started
2.1 Installation
Before installation, choose a location in the vehicle where it can:
• Provide convenient access for installing or removing the hard disk
• Allow air to flow around the fan vents. Inadequate or improper air flow can impede proper
operation of the mobile DVR
Please avoid installing the mobile DVR to the following locations in the vehicle:
• That is subject to high vibration / sunlight levels
• That is subject to be drenched of the rain
• Where passengers can interfere with the mobile DVR
• Next to a heater duct
The following table lists the recommended location options in the vehicle:
Location
Front of bulkhead-horizontal mount Yes Yes Yes Yes
locations have the highest levels of vibration and may be subject to water damage.
Convenient
Operation
Yes Yes Yes Yes
No Yes Yes Yes
Yes Yes No Yes
Yes Yes Yes Yes
Easy to
Install
Low
Vibration
Good
Air Flow
2.1.1 Mounting
You can mount the mobile DVR onto a surface inside the vehicle. Please note that to meet the
EN50155 and the SAE-J1455 standard for the mobile DVR, the Bracket on the MDVR is required
to be used.
6
EMV1200 FHD / EMV800 FHD Hybrid Mobile DVR
175mm/7"
207mm/8.14"
229.6mm/9.04"
5.5
192mm/7.55"
218mm/8.58"
236.6mm/9.3"
146.6mm/5.77"
76mm/2.99"
63.4mm/2.5"
Spacer with a cut
Screw Hole
Note:
Dimensions:
Installation: The Bracket is already installed on the mobile DVR. To mount the mobile DVR onto
a surface, use the supplied 4 black screws and 8 spacers (place 2 spacers on each screw hole).
2.2 Hard Disk Installation
You can insert a 2.5” HDD or SSD into the HDD tray for video recording. Please follow the
steps below.
1. The mobile DVR does not support hot swap for the hard disk. Ensure to power off the
mobile DVR before removing the hard disk. Also ensure to remove the hard disk only
after the power is completely shut-off. This would protect and extend the operating life
of the hard disk.
2. Please go to the EMV800 FHD / EMV1200 FHD Web page on our website
http://www.everfocus.com.tw to see the latest Storage Compatibility List. It’s
recommended to use the HDD/SSD models listed in the Storage Compatibility List to
ensure your storage will be compatible.
7
Loading...