EverFocus ED120 Series, ED220 Series Instruction Manual

IV. Specifications

ED120 ED200

Pickup Device: 1/3 inch B/W interline 1/3 inch Color

transfer CCD interline transfer CCD

Picture Element: 510 x 492 (EIA) 510 x 492 (NTSC)

500 x 580 (CCIR) 500 x 580 (PAL)

Horizontal resolution: 420 TV lines (EIA) 380 TV lines (NTSC)

400 TV lines (CCIR) 340 TV lines (PAL)
Sensitivity: 0.04 lux/F=2.0 2.5 lux/F=2.0
S/N ratio: Over 48 dB Over 48dB
Electronic shutter: Up to 1/100,000 Up to 1/100,000
Gamma Correction: > 0.45 0.45
Video output: 1.0Vp-p,75 ohm 1.0Vp-p,75 ohm
Audio Output: Yes --­Power source: 12VDC+/-10%, 12VDC+/-10%,

150mA Max. 250mA Max.
Sync. Mode: Internal Sync. Internal Sync.
Lens Mount: M12 x P0.5 M12 x P0.5
Dimension:

106mm Dia x 85mm H. 106mm Dia x 85mm H.

Operating Temperature: -10oC to +50oC-10

o

C to +50oC

ED120 Series
ED200 Series

INSTRUCTION
MANUAL

4) Wall Mount, aim to left:
Remove the iron case from the supporting
bracket by using screw driver to loosen the
two screws, which connect the iron case to
the supporting bracket. Turn the iron case
in 90-degree and mount into the supporting bracket again
by changing the screw holes in order to keep the screw
indicator on the top side.

qConnect the video output of the camera (yellow line) to a B/W

monitor (ED120) or a color monitor (ED200), or other video
device through a 75 ohm type coaxial cable with BNC female
connector at cable extension.

rConnect the DC+12V regulated power source of the camera

(red line) to the DC12V Power-in jack with 2mm, center+,
outer- plug.

sConnect the ground of the camera (black line) to the ground.

tConnect the audio output of the camera (white line) for EM120

to the audio connector of the monitor.

uPut the plastic cover back on the Dome Camera.

III. Installation Instructions

n The Dome camera's horizontal angle of view is 92-degree.

Decide the location to install the Dome camera.

o In application, the dome camera can be installed as the

following four (4) positions :

I. General

The ED120 & ED200 Series Camera are compact, full functioned
CCD Camera. Their stylish appearance can be applied as per
installer's ideal locations. These dome camera can be mounted
either on the ceiling or on the wall easily. ED120 used high
sensitive 1/3" B/W interline transfer CCD sensor and ED200 used
high sensitive 1/3" color interline transfer CCD sensor. Both
sensors are featured with Auto Electronic Shutter, Automatic
Gain Control, and ED200 includes Auto White Balance function.

II. Precautions

• Do not expose the camera to humidity and dust. Outdoor

application without shielding is not recommended.

• Handle with care. This camera consists of sensitive high

precision parts. Do not disassemble or install it on an
unstable base.

• Operate on DC+12V. Use a regulated power source only.

• Never face the camera toward the sun directly.

Full-Screen Width of View

= 2 X Distance between

Camera and Target

1) Ceiling Mount

2) Floor Mount

3) Wall Mount, aim to right

4) Wall Mount, aim to left

MED1G00500

pRemove the plastic dome cover. In order to get the correct picture,

please always keep the screw indicator of the iron case on the top
side.

1) Ceiling Mount :
The dome camera are set in the actual

position when the shipment is made.
they are ready to be installed.

2) Floor Mount :

Rotate the iron case in 180-degree so
that the screw indicator is on the top
side.

3) Wall Mount, aim to right :

Remove the iron case from the
supporting bracket by using screw
driver to loosen the two screws,
which connect the iron case to the
support bracket. Turn the iron case
in 90-degree and mount into the
supporting bracket again by changing
the screw holes in order to keep the

screw indicator on the top side.

screw indicator