EverFocus EBD430 User Manual

EverFocus

Operation Instructions

11//33”” CCCCD

D

33--AAxxiiss OOuuttddoooorr IIRR DDoom

Caa

C

meerraa

m

EEBBDD443300

mee

Operation Instruction

© 2009 EverFocus Electronics Corp

Please read this manual first for correct installation and operation. This manual should be retained for
future reference. The information in this manual was current when published. The manufacturer
reserves the right to revise and improve its products. All specifications are therefore subject to change
without notice.

All rights reserved. No part of the contents of this manual may be reproduced or transmitted in any form or
by any means without written permission of the EverFocus Electronics Corporation.

Precautions

1. Do not place any object on top of the cover.

2. Be careful when handling the camera, to prevent any damage do not drop it or subject it

to strong shock or vibration. Do not disassemble it or attach it on an unstable base.

3. Install the camera away from TV or radio transmitters, magnets, electric motors,

transformers and audio speakers because the magnetic fields generated from these devices
may distort the video image.

4. Install the camera away from heaters, or other heat generating devices as the high

temperature could cause deformation, discoloration or other damage to the camera.
Install the camera at where the temperature range will stay between -40°C to 50°C (-40°F
to 122°F).

5. Never aim the camera at the sun or other extremely bright objects whether it is in use or

not.

6. Do not touch the surface of CCD sensor directly with your fingers. Use a soft cloth to

remove any dirt from the camera body. If necessary, use lens tissue or a cotton tipped
applicator and ethanol to clean the CCD sensor and the camera lens. When the camera
is not in use, protect the surfaces covering the lens and IR emitters.

7. All warnings on the product and in the operating instructions should be adhered to.

8. Do not use attachments not recommended by the camera manufacturer as they may cause

hazards.

9. Do not allow anything to rest on the power cord. Do not locate this device where the cord

may be abraded or may cause a hazard by persons walking on it.

10. Do not overload wall outlets and extension cords as this can result in fire or electric

shock.

11. Never push objects of any kind into his appliance through cabinet slots as they may touch

dangerous voltage points or short out parts that could result in fire, electric shock or
damage to the camera.

12. Refer all work related to the installation of this product to qualified service personnel or

system installers.

Federal Communication Commission Interference

Statement

This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate this equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.

Note: There is a screw located in the focus ring and the zoom ring for
waterproofing purposes only. These are NOT set screws!! Please don’t loosen or
remove them.

Table of Contents

1.Product Overview ................................................................5

1.1 Features .......................................................................5

1.2 Accessory Parts List....................................................6

1.3 Specifications ..............................................................7

1.4 Dimensions...................................................................8

1.5 Camera Component Description..................................9

1.6 Related Products..........................................................9

2.Installation.........................................................................10

2.1 Wiring and Mounting ..................................................10

2.2 Adjusting Camera Position ........................................13

2.3 Adjusting Zoom and Focus ........................................14

4

CHAPTER 1 PRODUCT OVERVIEW

CHAPTER 2 INSTALLATION

Chapter

1

1.Product Overview

Equipped with a SONY Super HAD CCD II and removable IR cut filter, the EBD430 produces a
clear and sharp picture at night or in low light. The long range IR LEDs illuminate up to 30m/98
feet, which allows EBD430 to capture images in complete darkness. Designed with 3-Axis rotation
flexibility, you can easily position the camera at all angles. Moreover, it also provides exte rnal
adjustment rings for the vari-focal lens focus and zoom, to easily adjust the field of view. This
camera is waterproof (IP66) and comes with built-in heater for extreme outdoor applications.

Note: There is a screw located in the focus ring and the zoom ring for waterproofing purposes
only. These are NOT set screws!! Please don’t loosen or remove them.

1.1 Fea tures

z High sensitivity with SONY Super HAD CCD II
z 520 TVL of excellent high resolution technology
z Up to 30 meters/98 ft. of IR range
z Vari-focal lens to offer you a wide adjustment of field of view
z True Day/Night function with removable IR cut filter
z External control of lens zoom & focus
z 3-Axis rotation for flexible view angle
z Intelligent Variable-frequency IR control saves electricity and balances brightness
z Split glass design to avoid undesired IR light reflection into the lens barrel
z Up to 20,000 hours of high intensity IR LED lifespan
z Vandal resistant design to prevent damage or tampering
z Weatherproof and IP66 rated

5