EverFocus EBA1280 User Manual

Page 1
EBA1280 eZ.HD Series
1080p FHD IP66 IR Dome Camera
User’s Manual
EverFocus Taiwan:
2F., No.12, Ln. 270, Sec. 3, Beishen Rd., Shenkeng Dist., New Taipei City 222, Taiwan TEL: +886 2 2662 2338 FAX: +886 2 2662 3632 www.everfocus.com.tw
Page 2

1. Introduction

EverFocus eZ.HD series cameras – EBA1280 deliver 1080p full HD image quality. The model provides 2.8-12mm lens with ICR. Featured with Digital Wide Dynamic Range (D-WDR), the camera can provide clear images even under backlight circumstances where intensity of illumination can vary excessively. The EBA1280 supports both NTSC and PAL scanning systems and is IP66 certified.

1.1 Packing List

Camera x 1
Mounting Sticker x 1
L-Type Wrench x 1
Screw & Screw Anchor x 4
User Manual x 1

1.2 Features

Equipped with 1080p Full HD CMOS sensor to deliver stunning image
quality
Varifocal 2.8-12mm with ICR to capture the desired field of view
Extended IR range of up to 30m / 98ft. with 24 LEDs (depends on scene
IR reflectivity)
D-WDR to improve the visibility under high contrast scene
The flexible angle viewing with its 3-Axis rotation design allows wall or
ceiling mounting
IP66-rated with metal housing
Supports UTC function: Control camera OSD settings directly from DVR
end
1
Page 3
2
98mm / 3.86"
120mm / 4.72"
60.2mm / 2.37"
E320
EB45
Power Cable
Video Output Cable
1
2

1.3 Dimensions

1.4 Optional Accessory

BA-
Color / Material: White / Metal Size (Φ x H): 138 x 54mm / 5.43”x2.13” Weight: 700g / 1.5lb
BA-
Color / Material: White / Metal Size (W x D x H): 245x160x163mm / 9.65”x6.3”x6.42” Weight: 2.1kg / 4.63lb

1.5 Cable Description

No. Name Descriptions
1 Power Cable Connects to a 12VDC power source.
2 Video Output 1080p output, using 75 Ohm BNC-type coaxial cable.
Page 4
3
Outer Housing
Camera Base
Camera Body
Side Cut
Wall
Camera Base
Camera Body

2. Installation

1. Stick the supplied Mounting Sticker to the surface to mark the 4 screw positions. Drill four holes on the surface and insert the supplied 4 Screw Anchors into the screw holes. If you want to run the cable through the surface, drill a hole within the 4 screw area.
2. Unscrew the Outer Housing by twisting it counterclockwise and then remove it from the Camera Base.
3. Screw the Camera Base to the surface with the supplied four Screws.
a. If you want to wire the cables from the Side Cut on the Camera Base:
Attach the Camera Body to the Camera Base and run the cables through the Camera Base first, and then place the cable under the Side Cut. Finally, screw the Camera Base to the surface with the supplied 4 Screws.
Page 5
4
Wall
Camera Base
Camera Body
360
°
180
°
180
°
Zoom
Focus
b. If you want to wire the cables through the surface:
Attach and screw the Camera Base to the surface with the supplied 4 Screws, and then attach the Camera Body to the Camera Base.
4. Screw back the Outer Housing and adjust the camera angle simultaneously.
5. Connect the Power Cable to a 12VDC power source. Connect the Video Output Cable to a monitor or DVR.
6. For the first time installation, check whether the camera is properly focused. If not, you can optionally adjust camera zoom and focus by adjusting the Zoom Screw or Focus Screw using a slotted screwdriver.
Page 6
5
UP
DN
7. You can use the Joystick on the cable to configure camera OSD settings or switch to different video formats. Remove the Protection Cap from the Joystick before using it.
Switching Video Format:
Push the joystick up for 5 sec. to switch to
AHD.
Push the joystick right for 5 sec. to switch
to TVI.
Push the joystick down for 5 sec. to switch
to CVI.
Push the joystick left for 5 sec. to switch to
CVBS.
Configuring OSD Settings:
Push the Joystick up / down to select
among menu items.
Push the Joystick left / right to adjust the
level of the selected item.
Press the Joystick to enter the submenu or
exit the OSD Setup Menu.
Page 7
6
No
Main
Sub Menu
Sub Menu / Function
Brightness
0-100
Global
Center
FLC
BLC
0-7
Return
ATW
Gray World
R Gain
0-63
B Gain
0-63
Return
Gain Day/Night
Low/Middle/High
Gain Night/Day
Low/Middle/High
Color
B/W
Return
Contrast
Auto/Manual
0-20
Sharpness
Auto/Manual
0-20
Saturation
Auto/Manual
0-20
3DNR
Auto/Manual
0-20
2DNR
Auto/Manual
0-20
DWDR
Close/Open
Return
AHD
1080P25/1080P30/720P25/720P30
TVI
1080P25/1080P30/720P25/720P30
CVI
1080P25/1080P30/720P25/720P30
CVBS
PAL/NTSC
Apply & Reboot
Return
6
Language
ENG/CHN/CHN(T)/RUS/SPA/FRA/POL/ITA/POR/JAP/KOR/GRE
Mode
On/Off
Display
On/Off
X Position Start
0-100
Y Position Start
0-100
Width
0-100
Height
0-100
Return
Color
Red/Green/Blue
Transparency
On/Off
Return
Mode
On/Off
Display
On/Off
X Position Start
0-100
Y Position Start
0-100
Width
0-100
Height
0-100
Return

3. Configuration in the OSD Menu

1 AE
2 AWB
3 Day/Night
Image
4
Enhance
Exposure Mode
Mode
MWB
Auto
Mode
Video
5
Setting
7 Function
Privacy
Motion
Area 0-3
Area 0-3
Page 8
7
Color
Red/Green/Blue
Transparency
On/Off
Return
Return
8
Version
9
Reset
10
Save & Exit
11
Exit
Loading...