Everdure RBES92 Installation Manual

APPLIANCE DETAILS

Voltage: 220-240V

Frequency: 50Hz

Lamp Max: 2x20W G4 halogen lamps

Rated Input Power: 230W

GENERAL INFORMATION

Before installing and operating the range hood, carefully read the following important information regarding
installation safety and maintenance. Keep this information booklet accessible for further consultations.
The appliance has been designed to exhaust cooking fumes externally. Before installation, please ensure that
the following have been supplied and that the tools listed below are readily available.

WHAT IS SUPPLIED

Range hood (including one way valve for flue x 1) x 1
Installation kit x 1 – RBES63 & RBES91: Short bolts x 10, long screws x 7, plastic plugs x 7
Installation kit x 1 – RBES92: Short bolts x 8, Medium bolts x 4, long screws x 7, plastic plugs x 7
Mounting brackets x 3
Instruction booklet x 1

WHAT MAY BE NEEDED FOR INSTALLATION

Electric Drill Duct Tape
Tape Measure Jig Saw
Spirit Level Ladder
Screwdrivers Torch (If natural lighting is minimal)

INSTALLATION INSTRUCTIONS

Please ensure that before installing the range hood, all power is switched off.
Installation must be in accordance to the local electrical authority and codes.
This range hood must be earthed at all times for the operators’ safety.
The G.P.O. for the range hood should be positioned to enable the user to turn the power off, to enable
cleaning and any maintenance required.
The G.P.O. should be installed within 600mm from the rear of the unit.
Ensure that when installing the range hood, that it is protected from any possible damage from tools etc.
Ducting for this unit must be installed in accordance to the local authority.
Ensure that the fixings used for this range hood are suitable.
Check the area where the range hood is to be fitted, to ensure that it is structurally sound.

The Everdure RBES63, RBES91 & RBES92 range hoods are intended to be installed directly onto a wall.

4

DESIGNED TO PERFECTION

INSTALLATION OF THE EVERDURE RBES63 & RBES91 RANGE HOODS DIRECTLY TO A WALL

Ensure that the wall is structurally sound, and is capable of carrying the weight of the range hood.
The range hood can be placed at a minimum of 600mm away from an electric cooktop, or 650mm
minimum from a gas cooktop. The unit is held to a wall via 3 brackets (supplied with the unit):

1. Hook Bracket.

2. Centre Bracket (flat).

3. Top Bracket (U-shaped).
Place the hood main unit (no u-shaped section) against the wall at the correct position and mark off the top
of the unit. Remove the unit and measure up 22mm to get the top level for the hook bracket. Place the hook
bracket (hooks up) under the mark and mark in the 3 screw holes. Remove the bracket and drill three (3)
Ø8mm holes 100mm apart. Insert plastic plugs into the holes and fix the hook bracket onto the wall. Place
the hood main unit onto the hooks. See pic2.
Screw the centre bracket onto the back of the u-shaped section using the supplied short screws (this helps
keep the width at the back even with the front). Place the u-shaped section onto the main unit and fix in
place with 2 short screws.
Add the soot tube to the one way valve, and vent it outside. See pic3.
Calculate the final height of the u-shaped section and pull out the inside u-shaped section to a suitable
height (see pic4) to check. Mark the 2 sides near the top and push the inner section out of the way. Place
the top bracket (slots to the bottom) centred between the 2 marks, mark the 2 screw holes. Remove the
bracket and drill two (2) Ø8mm holes at the marks. Insert plastic plugs into the holes and fix the hook
bracket onto the wall (slightly loose). Note: The top edge of the u-shaped bracket matches the top edge of
the u-shaped section – adjust according to your own needs.
Pull up the inside u-section to allocate the top bracket correctly, and tighten the screws. Pull the u-section
over the bracket completely and fix into place with 2 screws at the sides (see pic5).

For timber framed houses, special care should be taken that all brackets are attached to areas that will
support the weight of the range hood.

DESIGNED TO PERFECTION

5