© 2008 EVENTIDE INC., ONE ALSAN WAY, LITTLE FERRY, NJ 07643 USA
THE EFFECTS
Mix
Feedback
Q
Wah Depth
(Vowel sound in Voc Wah)
WWW.EVENTIDE.COM
Feedback
(Time offset for type 2)
Number of
Stages
Base
Frequency
Drive / Tone
(Wave Slew on Opto)
Mix
MODFACTOR
Rotor/Horn
Balance
ToneNot Used Horn SpeedRotor Speed
Width
(In Stereo Only)
Stereo Width
(# of Stages on Vintage)
QUICK REFERENCE GUIDE
SHAPE KNOB
The Shape knob allows you to choose the source of
modulation on all effect types. The choices are Sine,
Triangle, Peak, Random, Ramp, Square, SMP/HLD, Envelope,
ADSR, and Expression Pedal (EXP PDL.)
“ENVELOPE” OR “ADSR”as Modulation Choices
Sensitivity
Sensitivity
Selecting ENVELOP or ADSR with the Shape knob will cause
the modulation to follow the attack of your playing, much
like on an Auto Wah. To adjust for various input levels, the
Speed knob becomes a Sensitivity control. Note that
selecting ENVELOP or ADSR with the Shape knob will cause
Tap Tempo, Slow/Fast/Brake, and S-Mod to have no effect.
You can also select ENVELOP or ADSR with the Mod Source
knob. In this case, the Mod Rate knob becomes a Sensitivity
control.
Feedback
Q/Range
Manual
Offset
Stereo Width
for Pan Effect
Mix
Mix
Pitch Spread
LowPass FilterNot Used RingMod Hz
BOTTOM ROW OF KNOBS (SECONDARY LFO)
D-Mod: [Depth-Mod] Amount of Amplitude Modulation
(AM). This knob "wiggles" the Depth Knob's parameter by a
little to a lot. (Fully counter-clockwise is OFF.)
S-Mod: [Speed-Mod] Amount of Frequency Modulation
(FM). This knob "wiggles" the Speed Knob's parameter by a
little to a lot. (Fully counter-clockwise is OFF.)
Mod Rate: Sets the secondary LFO rate. This knob controls
how fast both D-Mod and S-Mod "wiggle" their targets.
Range is 1/8th of Speed Knob to 8 times Speed Knob (with
Tempo OFF,) or Sync to 1/8th Note Divisions (with Tempo
ON.)
Mod Source: Sets the secondary LFO modulation source.
Choices are Sine, Triangle, Peak, Random, Ramp, Square,
SMP/HLD, Envelope, ADSR, and Pedal.
MODFACTOR
THE EFFECTS
Use footswitches to select presets and to bypass.
Presets are stored in pairs. Each pair of presets is called a Bank. 20 Banks - total of 40 presets
QUICK REFERENCE GUIDE
BANK MODE PLAY MODE
BANK # PRESET #
Toggle between BANK and PLAY MODE
by pressing and holding the
right footswitch for about 2 seconds.
The encoder knob changes the loaded
effect both in BANK and PLAY MODES.
© 2008 EVENTIDE INC., ONE ALSAN WAY, LITTLE FERRY, NJ 07643 USA
SHAPE KNOB
Use footswitches to Bypass, select Slow/Fast/Brake, or Tap Tempo.
LFO SWEEP DISPLAY
WWW.EVENTIDE.COM
Part # 141137 Rev H
Bank Preset 1
Active / Bypass
Bank Preset 2
Active / Bypass
Bank UP
(Hold for PLAY MODE)
Active / Bypass Tap Tempo
TEMPO MODE SLOW/FAST/BRAKE
Tempo is turned ON or OFF by pressing the encoder. When Tempo is ON, the Tempo LED flashes at the
Tempo rate. With Tempo OFF, the Tempo LED is OFF.
When Tempo is ON, Speed is set in rhythmic sub-divisions of the beat, i.e. common beat values rather than
in Hz.
EXPRESSION PEDAL
An Expression Pedal can be assigned to control any knob(s) except for the Shape
and Mod Source knobs. You can either program knob control or assign the
Modulation shape to "EXP PDL."
TO PROGRAM KNOB CONTROL:
1. Move Expression Pedal to Toe or Heel Position.
Effect LED blinks to show Pedal Programming is "LIVE."
2. To Assign Knobs:
Press full heel and turn any of the knobs.
Press full toe and turn any of the knobs.
3. To Unassign a Knob:
Keep the knob at the same value in full heel and full toe positions.
4. Remember - Save it or Lose it!
Pedal assignments are saved with Presets.
Expression Pedal controlling a single parameter will
display the parameter name and value as if you were
turning a Knob.
Expression Pedal controlling multiple parameters will
display the pedal value (from 0 to 100) and the
parameter Knobs shown as dots.
When the Pedal is used, the column above each dot is
used to indicate that the Pedal is controlling that
parameter.
“EXP PDL” CHOICE ON SHAPE OR MOD SOURCE KNOB
-Pressing and releasing the switch toggles Slow Mode on and off. The LFOs will slow down by a
predetermined factor, simulating the speed change of a rotary speaker cabinet.
-Pressing and holding the switch will engage Brake Mode. The LFOs will slow down at a constant rate
while the switch is held. Once the switch is released, Brake Mode is turned off and the LFOs will recover to
their previous rate.
-If the Shape or Mod Source knob is set to EXP PDL but there is no Expression Pedal plugged in, then Brake
Mode will mimic the effect of sweeping the Expression Pedal.
-If the time between pressing and releasing the switch is less than 1 second, Slow Mode will be toggled. If
it is greater than 1 second, Slow Mode will not be toggled.
TO SAVE A PRESET
1. Press and hold the Encoder for a few seconds.
2. Turn the Encoder to select the desired Bank # and Preset #.
3. To save the Preset, press and hold the Encoder again. Billboard displays "SAVED" and Save Mode exits.
4. To exit Save without saving, press and hold the encoder again without holding, or press any Footswitch.
Upon exit without saving, the Billboard displays "NO SAVE".
NOTE: When you save a new Preset, you overwrite the old Preset.
Selecting "EXP PDL" with the Shape knob or
Mod Source knob will override Expression Pedal
programming. This is the easiest way to get
WAH Pedal-like functionality from any of
ModFactor's effect types using an Expression
Pedal. Note that since an Expression Pedal will
be controlling modulation in this setting, the
Speed and S-Mod knobs, Tap Tempo, and
Slow/Fast/Brake will have no effect.
Press once to reset LFO
(Hold for BANK MODE)
Loading...