Eventide MicroPitch Stereo Delay / Pitch Shifter effectpedaal Eventide MicroPitch Delay quick guide

MicroPitch Delay Quick Reference Guide

Pitch A

Pitch of A Channel (left)

from 0 to 50 cents

Mix

Dry/Wet Mix

Depth

Amount/Intensity of

Pitch modulation

from the LFO or ENV

Preset LED Ladder

ACTIVE Button/LED

LED lit when ACTIVE

Press to toggle action of

ACTIVE Footswitch

LATCHING< >MOMENTARY

ACTIVE/BYPASS

Preset Mode: Load Preset

Pitch B

Pitch of B Channel (right)

from 0 to -50 cents

TAP/Preset

Press & Hold to toggle between

Preset Select and Tap Modes

Button/LED

Toggles Primary/Secondary

Parameter Control

LED ON = Secondary

LED OFF = Primary

Pitch Mix

Mix of Pitches A&B

Mono Out: Center 50/50

Stereo Out: Center A left, B right

Rate/Sens

LFO Mod Rate: 0.1-10Hz

Env Follower Sens: 0-100

TAP Button/LED

LED OFF = Preset Select Mode

LED ON = Tap Time in Seconds

LED Blinks = Tap Tempo in BPM

Press to toggle Tap Time/Tempo

Press & Hold to Save Preset

Knob Functions – Secondary Parameters

Delay A

Pitch A Delay

Time Mode 0-3 secs

Tempo Mode 0-6 secs

Tone

Center Flat

CW High Boost

CCW Low Boost

Mod

Modulation Type Select

Increased volume

decreases Pitch amounts

LFO modulates Pitches

Increased volume

increases Pitch amounts

IN

TS (mono) or TRS (stereo)

Mono/Stereo Switch

Left = Mono (TS plug)

Right = Stereo (TRS plug)

n Stereo, Tip is OUT1, Ring is OUT2

I

Rear Panel

OUT1 & OUT2

In Mono, both outputs have

the same dry signal

Press button to toggle

Secondary/Primary parameters

I/O Level Switch

Left - Guitar

Right - Line/Effects Loop

Delay B

Pitch B Delay

Time Mode 0-3 secs

Tempo Mode 0-6 secs

Feedback

Feedback 0-100%

Out Lvl

Center for unity gain

Boost/Cut output level

EXP

Connect Expression Pedal,

Auxiliary Switches or TRS MIDI

(See System Setup)

Power

9VDC center-negative

Mini USB

Software updates

& MIDI over USB

Expression Pedal

MIDI Messages

Morphing from Heel to Toe

An Expression Pedal can be used to change any
grouping of knob Parameters in one smooth
gesture. Programming an Expression Pedal is
easy. You simply need to set end points for Heel
& Toe. Here’s how:

1. Press Pedal fully Heel down.

2. Adjust any combination of the Parameter
control knobs.

3. Press Pedal fully Toe down.

4. Adjust any combination of the Parameter
control knobs.

5. Save it or lose it. See “Saving a Preset.”

Clear Expression Pedal Mappings

To clear the Expression Pedal mappings for the
knobs, hold the ACTIVE Footswitch and, while
holding, press the ACTIVE Button until the Preset

Ladder LEDs flash twice.

Note: To use an Expression Pedal, the Exp Pdl Jack
must be set to either [EXP] or [EXP + AUX]. See
System Setup to select.

Save Preset

Enter Save Mode by pressing and holding the TAP
Button, then a MIDI program change message will save
a Preset to the Preset Slot of the given value 1-127.

Load Preset

MIDI program change message loads the Preset
from the Preset Slot of the given value 1-127.

Note: The bottom two Ladder LEDs will be lit when
Presets 6–127 are selected via MIDI or Device Manager.

Receive/send using the USB Port or Exp Pdl Jack*.
CC 4: Expression Pedal
CC 9: TAP TEMPO
CC 14: ACTIVE/BYPASS (>=64 is Active)
CC 15: FLEX (doubles Pitch A & B, >=64 is ON)

Parameters: CC Messages Map

CC

20
21
22
23
24
25

Mix
Pitch A
Pitch B

Depth

Rate/Sens

Pitch Mix

CCPRIMARY SECONDARY

26

Tone

27

Delay A

28

Delay B

29

Mod

30

Feedback

Out Lvl

31

*Use a MIDI Converter Box
or a DIN to TRS or TRS cable

System Setup

Enter System Setup

To access these Global Settings, apply power while holding ACTIVE Footswitch and button.
Top two LEDs light when in System Setup. Changes are stored as they are made. Cycle power to exit System Setup.

Set MIDI Channel

PRESS

1 2 3 4 5...

Set MIDI Channel: Click TAP Button

Default = Omni

Set MIDI Clock

PRESS

ON

Factory Default = Off

16

BUFFER

PRESS

RELAY

DSP+FX

KILL-DRY

Toggles On or Off for each setting

Factory Default = Buffered

Catch Up ON/OFF

PRESS

Factory Default = Off

ON

Set Exp Pdl Jack Set Bypass Mode

EXP (Default)

PRESS

[EXP+AUX (Momentary)]

TIP = Expression Pedal
RING = FLEX

[TRIPLE AUX]

TIP = Increment Preset
RING = Decrement Preset
TIP + RING = Load Preset

Note: Times out after a few seconds

[MIDI BOX]

Receive and Send MIDI via a MIDI
Converter Box (Tip Active)

[MIDI TRS]

Receive MIDI directly with a DIN
to TRS or TRS cable.

EXP + AUX

TRIPLE AUX

MIDI BOX

MIDI TRS

(doubles Pitch A & B)

Presets - 5 On Board, 127 Via MIDI

The currently loaded Preset is indicated on the Preset LED Ladder. When a Preset is modified the Preset LED

blinks once.

Load Presets Save Presets

To select and load a Preset using Footswitches:

To save one of the 5 Presets using the Buttons:

1. TAP Footswitch selects Preset 1 to 5.
Preset 1 (top LED) to Preset 5 (bottom LED)

blinks.

2. ACTIVE Footswitch loads the Preset. LED stops
blinking.

NOTE: To select Preset, TAP Footswitch must be

in Preset mode. If TAP LED is lit, press and hold

TAP Footswitch.

1. Press & hold TAP Button

- Blinking Ladder and Button LEDs let you know
you have entered Save Mode.

2. TAP Button selects Preset 1 to Preset 5.

3. ACTIVE Button saves Preset

- LEDs stop blinking to let you know the Preset
is saved.

NOTE: Save Mode times out after a few seconds.
Pressing either Footswitch exits Save Mode.

Catch Up Knob Function

When a Preset is loaded or when toggling between Parameters using , Knob positions will not align with their
current Parameter values. As a result, turning a knob will likely cause an abrupt change in the sound.

With Catch Up ON, the sound does not change until the Knob is moved to the position corresponding to the
current value. The LED Ladder indicates whether the knob must be turned CCW (top LED blinks) or CW (bottom

LED blinks). The LED flashes more rapidly as the knob approaches the value set by the Preset. All five LEDs blink

once when the knob matches the stored Parameter value.

Note: To enable/disable Catch Up Knob Function, power up in System Setup mode and press TAP Footswitch to toggle
ON/OFF.

TAP Footswitch Functionality

Press & Hold the TAP Footswitch to toggle between Tap mode and Preset Select mode.
Press the TAP Button/LED to toggle between Tap Time and Tap Tempo as follows:

STATUS FUNCTION

LED OFF Tap OFF

LED ON

LED Blinks

at BPM

Tap Time

Tap Tempo

Press TAP Footswitch to increment presets

Tapping sets Delay A & Delay B in seconds. The maximum amount of
delay in Time Mode is 3 seconds.

Tapping sets Tempo in BPM. Delay A & Delay B are quantized to note
durations. The maximum amount of delay in Tempo Mode is 6
seconds and is a function of the BPM & selected Delay Note Length.

EFFECT

Device Manager Software

Available from Eventide’s website for Mac & PC

- Update Pedal Firmware - Backup/Restore entire device to a file

- Restore Factory Settings - Edit System Settings

- Import/Export Presets - View, edit, and organize Presets

Download: eventideaudio.com/edm

Restore Factory Settings: Boot pressing ACTIVE Footswitch & ACTIVE Button
Software Update: Boot pressing TAP Button & TAP Footswitch

MicroPitch Delay Quick Reference Guide for Firmware v1.0+| Eventide Part# 141347 Rev A
Eventide is a registered trademark of Eventide Inc. © 2021 Eventide Inc.

Note: A single tap
will always reset
the LFO phase

Instructional Videos

eventideaudio.com/MicroPitchDelay

Technical Support

eventideaudio.com/support

Follow us on Social