Page 1
AU
GAS BUILT-IN OVEN
installation
and
operating
OWNER'S HANDBOOK
instructions
Model No's
NOTE TO INSTALLER:
LEAVE THE OWNERS GUIDE MANUAL WITH THE APPLIANCE.
(Keep For Future Reference)
Page 2
Environmental protection advice
All the materials used are environmentally compatible and recyclable.Please make your contribution
to conserving the environment by using the separate waste collection channels available.
Read carefully all the instructions contained in this booklet. It provides you with important
information regarding the safe installation, use and maintenance of the appliance as well as
useful advice for getting the best out of your oven. Keep this booklet in a safe place for future
reference.
The manufacturer pays particular attention when printing its instruction manual however misprints may
occur. If the texts are unclear, please contact the service centre for explanations.
After removing the packing, check that the appliance is not damaged in any way. Be careful not to
leave the packing materials (plastic sheeting, expanded polystyrene etc.) in reach of children, as they
can be dangerous.
IMPORTANT: do not use the oven door handle to move the appliance, such as when removing
it from the packaging.
WARNING:
Before using the appliance, do not forget to remove the protecting parts of the appliance.
GENERAL INFORMATION
Oven's ratings and serial number are written on
the data plate (A) and (B) sealed inside the front
of the oven.
WHEN YOU CALL FOR SERVICE
When you call for service or order parts for
your unit, be sure to give:
1. MODEL
2. SERIAL NUMBER
3. COLOUR
4. PART NAME and/or description of problem
5. YOUR FULL NAME, ADDRESS, and HOME
TELEPHONE
NUMBER and BUSINESS TELEPHONE
NUMBER IF APPROPRIATE.
Servicing shall be carried out only by authorised
personnel.
ENVIRONMENTAL WARNING
Waste packaging
Do not throw the packaging of your appliance into the dustbin,
but pick out the different materials (for instance foil, paperboard,
polystyrene) according to the local rules for rubbish elimination.
This appliance must only be used for the purpose of domestic
cooking.
RECORD HERE FOR EASY REFERENCE
Model Colour
Serial Number Installation Date
Dealer's Name and Address
2
GENERAL WARNINGS
A
WARNING
Remember ovens get hot: some parts naturally become
very hot, notably the glass oven door and the protective
strip. KEEP CHILDREN AWAY FROM Oven AT ALL
TIMES AND WARN THEM ABOUT THE DANGER.
When connecting or using appliances connected to a
plug near your oven KEEP THE MAINS CABLE FAR
FROM HOT SURFACES OF THE OVEN.
Front oven
(A) Data plate
(B) Serial
number
Page 3
WHERE THIS APPLIANCE IS INSTALLED IN MARINE CRAFT OR IN CARAVANS, IT SHALL NOT
BE USED AS A SPACE HEATER
DO NOT MODIFY THIS APPLIANCE.
DO NOT USE OR STORE FLAMMABLE MATERIALS NEAR THIS APPLIANCE.
Make sure that the knobs are on 0 (closed) when the appliance is not in use.
IMPORTANT
This appliance must be used exclusively for cooking food and for no other purpose.
Any other use of the appliance (such as heating a room) is incorrect and therefore dangerous.
The manufacturer can not be considered responsible for possible damages arising from a wrong
installation.
The manufacturer can not be considered responsible for possible damages arising from a
wrong installation or incorrect use of the appliance.
- Installation and maintenance have to be done by qualified staff only.
- The appliance should only be used for the cooking of food and not for any other use.
- The safety of this appliance is assured only when it is correctly connected to a good system of
previewed grounding, like from the norms.
- When in use the appliance becomes very hot. Do not touch the heated elements inside the oven.
- Do not touch the appliance with humid or wet hands or feet.
- Do not use the appliance barefoot.
- Do not pull the feeding cable in order to detach the plug from socket.
- Do not leave the apparatus exposed to atmospheric agents (rain, sun and so on).
- Do not allow the appliance to be used by children.
- Dont let children sit down or play with the oven door. Do not use the drop down door as a stool to
reach above cabinets.
- Care should be taken to avoid touching heating elements inside the oven.
Do not place heavy objects on the oven door when it is open.
WARNING - Accessible parts will become hot when in use.
To avoid burns and scalds children should be kept away.
WARNING
This appliance is not intended for use by persons (including children) with reduced physical, sensory
or mental capabilities, or lack of experience and knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
Young children and infirm persons should not be left unsupervised in the vicinity.
WARNING
A steam cleaner is not to be used cleaning this appliances.
Keep the appliance thoroughly cleaned. Food residues may cause fire risks.
In the instance of malfunctions, never attempt to repair the appliance yourself. Repairs by unskilled
persons may cause damage and accidents. First refer to the contents of this manual.
If you do not find the necessary information, contact your nearest Service Centre.
Servicing work on this appliance must be carried out by an authorised Technical Service Centre.
Always request the use of original spare parts.
3
DO NOT SPRAY AEROSOLS IN THE VICINITY OF THIS APPLIANCE WHILE IT IS IN OPERATION.
Not for use in marine craft, caravans or mobile homes unless the burners is fitted with a flame safeguard.
Page 4
Make sure that air is able to circulate freely around the appliance. Poor ventilation produces a shortage
of oxygen.
Make sure that the appliance is supplied with the type of gas indicated on the relative sticker next to
the mains gas connection pipe.
Use of a gas oven appliance produces heat and moisture in the room in which it is installed. Ensure
that the room is well ventilated by keeping the air intakes open and in good working order or by installing
an extractor hood with discharge pipe.
If the appliance is used intensively for a long time the effectiveness of the ventilation will have to be
increased, for example by opening a window or increasing the power of any electric extractor fan.
The appliance must be installed in accordance with the requirements of AS/NZS 3000.
IMPORTANT: The rating data plate is attached to the front of the oven.
Supply voltage 220 - 240 V~ 50 Hz
Oven capacity 56 lt
Dimensions: Height cm 31.5
(oven usable Width cm 43.5
volume) Depth cm 41.5
Power: Oven burner
MJ/h
8.64 (Natural Gas), 7.50 (ULPG)
Electric grill W 1600
Cooling fan motor W 22
The Oven Lamp
(Type E14 threaded T 300°C)
W 15
These instructions address appropriate installers and serve as a guide for installation, adjustment
and maintenance in conformity with the laws and regulations in force.
4
GAS CONNECTION
The appliance shall be installed by an authorized person in accordance with the manufacturers
installation instructions, relevant local fitting regulations, municipal building regulations, the AS 5601
gas installations and other relevant statutory codes and regulations. If you have some doubts, please
contact the authorities for confirmation concerning the characteristics of the gas and electricity output.
This appliance can be connected with rigid pipe as specified in AS5601 table 3.1 or with a Flexible
Hose which complies with AS/ANZ 1869 (AGA Approved), 10mm ID, class B or D, no more that 1.2m
long and in accordance with AS5601. Ensure that the Hose does not contact the hot surfaces of
the oven. The Hose should not be subjected to abrasion, kinking or permanent deformation
and should be able to be inspected along its entire length. Unions compatible with the hose
fittings must be used and connections tested for gas leaks.
The supply connection point shall be accessible with the appliance installed.
The appliance is generally preset for natural gas (so no other adjustment is necessary) and equipped
with a regulator with pressure test point.
If the natural gas regulator supplied with the appliance does not have a pressure test point, a pressure
test point assembly must be fitted.
Ensure that all foreign matter has been cleared from the gas supply line and also purge all air from
the gas system. Connect the regulator, tighten and check the installation to ensure no gas leaks occur.
Check gas pressure, note the correct setting from the data plate sealed on the front of the oven.
TECHNICAL FEATURES
INSTALLATIONS INSTRUCTIONS
IMPORTANT NOTICE TO THE INSTALLER
VENTILATION
Ventilation must be in accordance with AS5601-Gas Installations. In general, the appliance should
have adequate ventilation for complete combustion of gas, proper flueing and to maintain temperature
of immediate surroundings within safe limits.
Page 5
When the installation is complete, always check that all the unions are absolutely tight using a
soapy solution. Never use a flame to make this check.
IT IS RECOMMENDED THAT A SERVICE TAP AND UNION BE
FITTED ADJACENT TO THE APPLIANCE INLET TO FACILITATE
FUTURE SERVICING.
5
ELECTRICAL CONNECTION
The appliance must be installed by a suitably qualified person in accordance with
these instructions and with the requirements of the Australian Wiring Rules AS/NZS 3000.
Fixed wired installations are to be provided with suitable isolation means in accordance with the said
rules.
Any plug socket installed for the purpose of connecting the appliance to supply must be readily
accessible when the appliance is installed.
Before making the connection, make sure that:
1) the safety circuit-breaker and the electrical system are able to withstand the load of the appliance
(see nameplate).
2) the power supply system has an earth connection in good working order in accordance with the
regulations in force;
IMPORTANT
The wires in the mains lead are coloured in accordance with the following code:
GREEN & YELLOW...............................................................EARTH
BLUE.................................................................................NEUTRAL
BROWN ....................................................................................LIVE
Electric power
Gas appliances with electric grill................3X1 mm
2
core cable (10 amp. Fuse required)
Should conform to local authority requirements.
Also refer to rangehood manufacturers recommendations.
This appliance is supplied with a plug & cord, simply plug into a 3 pin household socket outlet witch
is properly earthed.
WARNING: THIS APPLIANCE MUST BE EARTHED.
The flexible mains lead and plug must not be in contact with hot surfaces.
CONNECTIONS
The Gas Connection is male 1/2" BSP and is situated at the right hand rear of the appliance, 20 mm
from the side and 500 mm from the bottom of the oven.
Should conform to local gas authority requirements.
Also refer to rangehood manufacturers recommendations.
Where there is limited access to the gas regulator or pressure test point, the regulator can be installed
inside an adjacent cupboard at the end of the hose assembly.
VERY IMPORTANT FOR THE INSTALLER
Do not attempt to turn or stress threaded elbow of the manifold: you risk damage to this part of the
gas appliance which may void the manufacturers warranty.
Apply a manometer to the test nipple and reset the regulator if necessary.
Check the burners pressure (grill and oven) all operating on high flame.
Do not forget to replace the test nipple screw and to leave the instructions book with the user.
Important: several parts are protected with a special anti-scratch film. Please remove it before use.
Page 6
INSTALLING THE APPLIANCE
For the most efficient air circulation, the oven should be fitted according to the dimensions shown in
fig. 2.
FITTING THE APPLIANCE
Fit the appliance into its surround (beneath a work-top or above another appliance) by inserting screws
into the holes that can be seen in the frame of the oven when the door is open (fig. 2).
IMPORTANT
The panels of the adjoining furniture should be heat resistant. Particularly when the adjoining furniture
is made of veneered wood, the adhesives should be able to withstand a temperature of 90°C.
Plastic materials or adhesive which cannot withstand this temperature will become deformed or unstuck.
To comply with safety regulations, once the appliance has been fitted it should not be possible to make
contact with the electrical parts.
All parts which offer protection should be fixed in such a way that they cannot be removed without the
use of a tool.
We recommend that installation, connection and preparation of the cabinet are carried out by a qualified
technician accordingly with the instructions of this booklet and with the installation requirements or
regulations in force in the user's Country
How to remove packing
After having removed internal and external packing ensure that the apparatus is intact and not damaged.
If you are not sure do not use the oven, and call your Retailer.
Some points are protected with a plastic coating.
It is absolutely necessary to eliminate this covering before using the appliance.
The elements used for packing (cardboard, bags, polystyrene, cards) must be kept away from
children because they are a potential source of danger.
Installation, regulation, transformation, maintenance should only be done by qualified personnel
only.
580
fig. 2
6
PREPARATION ON THE CABINET
screw
screw
Screws fitting
Page 7
TAB. D
Natural Gas 1.00
Jet mm Ø Burners Power MJ/h
Oven
NG Regulator
Gas Type kPa
U - LPG 2.75
Jet mm Ø Burners Power MJ/h
Oven
LP Test point
adaptor
Gas Type kPa
1.35 8.64
7.50
0.73
7
GAS CONVERSION AND ADJUSTMENT
SPECIAL NOTE
When converting from Natural Gas to U-LPG ensure that the NG regulator is removed and replaced
with the Test Point Assembly. A gas regulator suitable for a supply pressure of 2,75kPa should be part
of the gas tank supply.
After installation or any servicing operation, always ensure that the appliance is gas sound and that
the components are now operating correctly. Items removed during servicing should be replaced in
the reverse order to their removal.
Fig. B
GAS CONVERSION AND ADJUSTMENT
If the appliance requires a different type of gas than
the kind available, the injectors must be changed
and the minimum adjusted.
Oven burner
To change the oven injector, it is necessary to act as
follows: open the oven door, remove the lower side
A, unscrew screw B (fi.g A) and disassemble the oven
burner C (see fig.B). Change the injector (see fig. B)
and replace it with another one suitable for the new
gas type (see table D).
Re-assemble everything in the opposite direction,
paying attention to place the burner in the right way
on its rear slot.
C
Injector
A
B
B
A
Fig. A
Fan assisted gas oven
Fan assisted gas oven
When used with natural gas all burners have been preset at our factory and further adjustment should
not be necessary. Conversion kits to other gases are available from the place of purchase.
Do not attempt to fit the conversion kit yourself. Conversion to U-LPG gas should only be carried out
by an authorized technician.
Page 8
Z
8
MINIMUM FLOW ADJUSTMENT FOR OVEN
THERMOSTAT
In order to adjust the minimum, act as follows: switch
the burner on turning the knob to the maximum position.
Remove the knob and unscrew of some turns the bypass screw (fig. I).
Assemble the knob and let the oven warm up for 15
minutes; after that turn the knob to the maximum
position.
After having removed the knob once again, making
sure that the thermostat rod has not been moved,
screw slightly the above mentioned by-pass screw, to
obtain a flame of 3 or 4 mm of length.
For U-LPG, the adjusting screw must be tight screwed.
Make sure that the flame does not extinguish passing
quickly from the maximum flow to the minimum flow,
and closing and opening the oven door (the oven door
must be closed softly).
Fig. I
Page 9
It is important that all the operations related to installation and regulation be carried out by specialised
staff in accordance with the norms in force. The specific instructions are described in the chapters for
the installer. Before using the appliance, carefully remove the special protective film that protects the
stainless steel or anodized aluminium items.
The ovens thermal isolation and the grease residue from the work produce smoke and unpleasant
odours during the first few minutes of use. We advise heating the empty oven to maximum temperature
for about 45 minutes at first use.
Use of the gas oven
When using the oven for the first time, set the temperature to its highest level and heat for
about 30 minutes with the oven door closed. Open all windows wide to eliminate any odours
and fumes produced by internal components.
It is something normal, and in case it will occur, wait for the smoke to stop before introducing the food
into the oven.
The oven is fitted with: a rod shelf for cooking food contained in oven dishes or placed directly on the
rod shelf itself, a drip-tray for cooking sweets, biscuits, pizzas, etc., or for collecting juices and fats
from food cooked directly on the rod shelf.
warnings: do not cook foods on the bottom in the base of the oven.
Fig. 5
ELECTRICAL IGNITION
Open the oven door . Turn the knob anti-clockwise
until the pointer to the maximum power (fig.5).
When the knob is pressed, the electrical ignition
will automatically be activated.
MANUAL IGNITION OF OVEN BURNER
Open the oven door and place a lighted match
close to the hole of the oven bottom plate
(fig. 4A). Turn the knob anti-clockwise until the
pointer to the maximum power (fig.5), and keep
the knob pressed for about 15 seconds to heat
up the thermocouple bulb, and then release it.
If the burner does not remain on, repeat the
operation.
Fig. 4A
keep the knob pressed for about 15 seconds to
heat up the thermocouple bulb, and then release
it. If the burner does not remain on, repeat the
operation.
To turn off the burner, turn the knob clockwise
to the vertical position marked by the ( ) symbol
(fig. 5).
= Closed
= MIN.
= MAX.
160°C
265°C
160
180
200
230
250
265
Oven cooking
Before use, heat the oven to the desired
temperature. Upon reaching the desired
temperature, introduce food and check the cooking
temperature, taking care to turn it off 5 minutes
before the end of the cooking time in order to
recover the stored heat.
WARNING: the oven must be used with the oven
door closed.
9
USE
Gas oven
The thermostats are equipped with a safety device which prevents accidental opening.
In addition, if the flame goes out accidentally, the safety of the gas system is assured by a thermocouple
which is tripped automatically and cuts off the flow of gas to the burner concerned.
N.B.: Always make sure that the oven door
is open before lighting the burner.
After making sure that the burner has lit properly,
gently close the oven door. To obtain the
temperature required, simply turn the pointer of
the knob to the chosen number (fig. 5).
WARNING: Do not operate the ignition for
more than 20 seconds. If the burner fails to
ignite, leave the oven door open for at least
1 minute before pressing the knob again.
Page 10
WARNING:
the oven and grill must be used with the oven
door closed.
Grill Cooking
The heat comes from above.
Suitable for:
thin meat; toast.
Advice for grill cooking
Almost all meat can be cooked on the grill except
for several thin, game meats and meatloaf.
The meat and fish to be cooked on the grill should
be sprinkled with oil and placed on the grill; the
former is moved nearer or further away from the
grill element based on the thickness of the meat
in order to avoid burning it on the outside and
not cooking it enough on the inside.
Add 1 cup of water to the drip tray to avoid the
creation of smoke caused by sauce or grease
drippings.
Put the drip tray on the first level (fig. 7B).
Fig. 7B
Oven light .
USE OF THE OVEN FAN FUNCTION
Fig. 7F
- Place the chicken or meat cut to be roasted on
the spit L, so that it is firmly held in place by the
two prongs F (fig. 7D).
- Place the spit on the support G.
- Insert the support G completely inside the oven
so that rod L goes inside hole of the turnspit
motor M .
- Position the dripping pan, with some water inside,
underneath the support G.
- Close the oven door.
The turnspit is an optional available only in some
models.
Use of the turnspit .
For electric grill models turn the knob in position
(fig. 7F).
To remove the spit, carry out the inverse procedure,
using the knob A and a heat-proof oven glove.
10
TURNSPIT ( optional )
Use of the fan assisted electric grill (fig. 7F)
The air which is heated by the grill heating element
is circulated by the fan which distributes the heat
on the food.
The fan assisted grill replaces perfectly the turnspit.
You can obtain very good results also with large
quantities of poultry, sausage, red meat.
Defrosting with fan (fig. 7F)
The air at ambient temperature is distributed inside
the oven for defrosting food very quickly and without
proteins adulterations.
NOTE: this function must be used with the oven
thermostat in position ( 0 ) OFF.
Level
4
3
2
1
5
Grids
Drip dray
Use of the fan assisted gas oven (fig. 7F)
The air which is heated by the gas burner is circulated
by the fan which distributes the heat on the food.
NOTE: this function must be used with the oven
burner on and the fan switch on.
F
L
G
M
fig. 7D
A
Page 11
Cooking times
Cooking times may vary based on the type of food,
its homogeneity and thickness.
It is advised to watch the cooking process the first
few times and verify the results so that, when making
the same dishes under the same conditions, similar
results may be obtained.
Fig. 7C
NOTE:
Install shelves by locating them in the
horizontal guide rails on the oven walls.
The raised portion of the shelf is to be facing the
rear wall of the oven (fig. 7C).
Warning: the positions for shelves are
5
4
3
2
Bump
NOTE: oven shelves
The shelves are designed with stop-locks so
when placed correctly on the shelf supports, they
will stop before coming completely out of the
oven and will not tilt when you are removing food
from them or placing food on them.
When placing cookware on a shelf, pull the shelf
out to the bump on the shelf support. Place the
cookware on the shelf, then slide the shelf back
into the oven. This will eliminate reaching into the
hot oven.
To remove the shelves from the oven, pull them
forward you, tilt front end upward and pull them
out.
To replace, it in the opposite manner as before.
11
DESCRIPTIONS OF ACCESSORIES
front part
Oven accessories
A = wire shelves
B = Drip dray (optional)
C = Grill pan set
AB C
Page 12
PCI "Campanil"TR 259 Analogic (Fig. 7L)
Setting the clock
Pull the control knob and turn clockwise.
Alarm programme adjustement
Turn the knob clockwise without pulling it in.
At the end of the programmed time an alarm will
sound. To cancel it, turn the knob to the bell.
Turn the knob clockwise, stopping the pointer
in line with the selected time. The timer can be
set from 1 to 60 minutes. When the preset time
is over, a buzzer will sound.
XII
XI
X
IX
VIII
VII
VI
V
I
II
III
IV
Fig. 7L
Fig. 7M
1 Time of the day
2 Timing and insertion
3 Signal timng and insertion
Fig. 7N
12
MINUTE COUNTERS (fig. 7N)
O
45
5
35
25
15
55
Reset timer
Press + and - buttons together and release
+ button first.
Signal
The signal after time out will stay 7 minutes if it
has not been reset with the + button (one touch
only).
Signal frequency
When the display shows the time of day, the signal
frequency can be selected by pressing the -
button. Three different frequencies are selectable.
ELECTRONIC TIMER FOR COOKER (Fig. 7M)
Functions
On
The display flashes.
Time setting
Press the left button.
Set the time with buttons + and -.
This function remains activated 7 seconds after
the last +/- operation.
Timer setting
This function is permanently activated and it will
be immediately set with +/- buttons.
During setting the units are 10 seconds.
During count down the timer takes priority on the
display.
The units are seconds.
The maximum time is 99 minutes.
The relay contact (when available) is closed during
the count down only.
Page 13
Removal of oven door
To make cleaning easier, remove the oven door as
follows:
1) open the door halfway and remove the glass
stoppers A, the profile B (as shown in fig. 8)
and the glass C, as shown in fig. 8A.
2) open the oven door completely.
3) flip the hinge hooks "A" outwards (see fig. 8B).
4) shut the oven door slowly until it reaches
hooks "A", making sure these are locked into
slots "B" of the oven door, as shown in fig.8C.
5) Using both hands, push the oven door lightly
inwards, toenable the door hinges "C" to come
away from the slots "D" (see fig. 8D) and pull
the door towards you until it is released from the
oven. After cleaning it, reposition it correctly
following the abovesteps in the reverse order
and flipping hooks "A" inwardsbefore you shut
the oven door (fig. 8E).
CLEANING AND MAINTENANCE
Cleaning should be carried out when the
appliance is COOL.
Do not use steam cleaners to clean the oven.
Always clean off spillage as quickly as possible to
prevent burning on which will make removal more
difficult. Wash with a clean cloth soaked in hot soapy
water, rinse and dry with a soft cloth. Do not use
abrasives, caustic pastes or sprays, coarse cleaning
pads or powders.
The oven accessories (shelve, grid, oven shelf
carriers) and the oven door also, can be removed
for easier washing, to be done with a mild detergent
solution. The slots in the front of the appliance for
the passage of the air must carefully kept unobtructed for an efficient cooling of the unit.
CAUTION: do not use rough or abrasive materials
or sharp metal scrapers to clean the glass doors of
the oven since they may scratch the surface and
cause the glass to break.
CLEANING AND MAINTENANCE
N.B.: BEFORE DOING ANY MAINTENANCE WORK, DISCONNECT THE POWER SUPPLY AND TURN
OFF THE GAS TAP OF THE GAS CYLINDER OR THE GAS SUPPLY MAIN.
13
B
Fig 8A
Fig 8
A
C
AA
A
B
A
Fig. 8C
Fig. 8B
C
D
Fig. 8D
A
Fig. 8E
Page 14
Oven light (fig. 10)
The oven bulb is a special kind which is resistant to
high temperatures. Replace it as follows: disconnect
the oven from the power supply by removing the
plug or switching off the power supply at the mains;
remove the protective glass (A) and replace the
burnt-out bulb with one of the same type. Replace
the protective glass.
Fig. 10
Self-cleaning panels
If the oven is fitted with self-cleaning panels, at normal cooking temperatures the catalytic enamel helps
transform grease splashes into a light dust. This dust can be removed with a damp sponge when the oven
has cooled down. This helps keep the surface of the enamel porous and ensures maximum cleaning efficiency.
The self-cleaning panels and the shelves frame are very easy to remove
(see fig. 11 - 12 - 13 - 14).
Fig. 11
Fig. 12
Fig. 13
Fig. 14
Maintenance schedule:
To ensure the appliance continues to operate at peak performance, we recommend
a routine service call every 2 years for the life of the appliance.
14
Important: if the oven is no longer to be used, it should be made inoperable by cutting the power
supply cable, after unplugging it from the power supply. Disused appliances can be a safety risk
as children often play with them. For this reason it is advisable to make the oven safe.
T300°C
A
Page 15
15
Page 16
Loading...